diff options
Diffstat (limited to 'docs/services')
| -rw-r--r-- | docs/services/ipoe-server.rst | 57 |
1 files changed, 38 insertions, 19 deletions
diff --git a/docs/services/ipoe-server.rst b/docs/services/ipoe-server.rst index 69682217..eda1762a 100644 --- a/docs/services/ipoe-server.rst +++ b/docs/services/ipoe-server.rst @@ -4,8 +4,19 @@ IPoE Server ########### -VyOS utilizes `accel-ppp`_ to provide IPoE server functionality. It can be -used with local authentication (mac-address) or a connected RADIUS server. +VyOS utilizes `accel-ppp`_ to provide :abbr:`IPoE (Internet Protocol over +Ethernet)` server functionality. It can be used with local authentication +(mac-address) or a connected RADIUS server. + +IPoE is a method of delivering an IP payload over an Ethernet-based access +network or an access network using bridged Ethernet over Asynchronous Transfer +Mode (ATM) without using PPPoE. It directly encapsulates the IP datagrams in +Ethernet frames, using the standard :rfc:`894` encapsulation. + +The use of IPoE addresses the disadvantage that PPP is unsuited for multicast +delivery to multiple users. Typically, IPoE uses Dynamic Host Configuration +Protocol and Extensible Authentication Protocol to provide the same +functionality as PPPoE, but in a less robust manner. .. note:: Please be aware, due to an upstream bug, config changes/commits will restart the ppp daemon and will reset existing IPoE sessions, @@ -14,11 +25,15 @@ used with local authentication (mac-address) or a connected RADIUS server. Configuration ============= -IPoE can be configure on different interfaces, it will depend on each specific situation which interface will provide IPoE to clients. -The clients mac address and the incoming interface is being used as control parameter, to authenticate a client. +IPoE can be configure on different interfaces, it will depend on each specific +situation which interface will provide IPoE to clients. The clients mac address +and the incoming interface is being used as control parameter, to authenticate +a client. -The example configuration below will assign an IP to the client on the incoming interface eth2 with the client mac address 08:00:27:2f:d8:06. -Other DHCP discovery requests will be ignored, unless the client mac has been enabled in the configuration. +The example configuration below will assign an IP to the client on the incoming +interface eth2 with the client mac address 08:00:27:2f:d8:06. Other DHCP +discovery requests will be ignored, unless the client mac has been enabled in +the configuration. .. code-block:: none @@ -29,8 +44,9 @@ Other DHCP discovery requests will be ignored, unless the client mac has been en set service ipoe-server interface eth2 client-subnet '192.168.0.0/24' -The first address of the parameter ``client-subnet``, will be used as the default gateway. -Connected sessions can be checked via the ``show ipoe-server sessions`` command. +The first address of the parameter ``client-subnet``, will be used as the +default gateway. Connected sessions can be checked via the ``show ipoe-server +sessions`` command. .. code-block:: none @@ -44,8 +60,9 @@ Connected sessions can be checked via the ``show ipoe-server sessions`` command. IPv6 SLAAC and IA-PD -------------------- -To configure IPv6 assignments for clients, two options need to be configured. A global prefix which is terminated on the clients cpe and a delegated prefix, the client can use -for devices routed via the clients cpe. +To configure IPv6 assignments for clients, two options need to be configured. +A global prefix which is terminated on the clients cpe and a delegated prefix, +the client can use for devices routed via the clients cpe. IPv6 DNS addresses are optional. @@ -68,14 +85,17 @@ IPv6 DNS addresses are optional. ipoe0 | eth3 | 08:00:27:2f:d8:06 | 192.168.1.2 | 2001:db8::a00:27ff:fe2f:d806/64 | 2001:db8:1::/56 | | active | 01:02:59 | 4626faf71b12cc25 -The clients cpe can now communicate via IPv4 or IPv6. All devices behind ``2001:db8::a00:27ff:fe2f:d806/64`` can use addresses from ``2001:db8:1::/56`` and can -globally communicate without the need of any NAT rules. - +The clients :abbr:`CPE (Customer Premises Equipment)` can now communicate via +IPv4 or IPv6. All devices behind ``2001:db8::a00:27ff:fe2f:d806/64`` can use +addresses from ``2001:db8:1::/56`` and can globally communicate without the +need of any NAT rules. Automatic VLAN creation ----------------------- -To create VLANs per user during runtime, the following settings are required on a per interface basis. VLAN ID and VLAN range can be present in the configuration at the same time. +To create VLANs per user during runtime, the following settings are required on +a per interface basis. VLAN ID and VLAN range can be present in the +configuration at the same time. .. code-block:: none @@ -85,23 +105,22 @@ To create VLANs per user during runtime, the following settings are required on set service ipoe-server interface eth2 vlan-range 1000-2000 set service ipoe-server interface eth2 vlan-range 2500-2700 - RADIUS Setup ------------ -To use a RADIUS server for authentication and bandwidth-shaping, the following example configuration can be used. +To use a RADIUS server for authentication and bandwidth-shaping, the following +example configuration can be used. .. code-block:: none set service ipoe-server authentication mode 'radius' set service ipoe-server authentication radius-server 10.100.100.1 secret 'password' - Bandwidth Shaping ^^^^^^^^^^^^^^^^^ -Bandwidth rate limits can be set for local users within the configuration or via RADIUS based attributes. - +Bandwidth rate limits can be set for local users within the configuration or +via RADIUS based attributes. Bandwidth Shaping for local users ================================= |