diff options
Diffstat (limited to 'docs/vpn')
| -rw-r--r-- | docs/vpn/wireguard.rst | 69 |
1 files changed, 67 insertions, 2 deletions
diff --git a/docs/vpn/wireguard.rst b/docs/vpn/wireguard.rst index 141e843c..2e16ad2e 100644 --- a/docs/vpn/wireguard.rst +++ b/docs/vpn/wireguard.rst @@ -10,8 +10,16 @@ information. Configuration ^^^^^^^^^^^^^ +Wireguard requires the generation of a keypair, a private key which will decrypt +incoming traffic and a public key, which the peer(s) will use to encrypt traffic. + +Generate a keypair +~~~~~~~~~~~~~~~~~~ + Generate the keypair, which creates a public and private part and stores it within VyOS. +It will be used per default on any configured wireguard interface, even if +multiple interfaces are being configured. .. code-block:: sh @@ -26,6 +34,27 @@ traffic to your system using this public key. wg01# run show wireguard pubkey u41jO3OF73Gq1WARMMFG7tOfk7+r8o8AzPxJ1FZRhzk= + +Generate named keypairs +~~~~~~~~~~~~~~~~~~~~~~~ + +Named keypairs can be used on a interface basis, if configured. +If multiple wireguard interfaces are being configured, each can have +their own keypairs. + +The commands below will generate 2 keypairs, which are not releated +to each other. + +.. code-block:: sh + + wg01:~$ configure + wg01# run generate wireguard named-keypairs KP01 + wg01# run generate wireguard named-keypairs KP02 + + +Wireguard Interface configuration +~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ + The next step is to configure your local side as well as the policy based trusted destination addresses. If you only initiate a connection, the listen port and endpoint is optional, if you however act as a server and endpoints @@ -55,6 +84,18 @@ the wireguard interface `wg01`. Multiple IPs or networks can be defined and routed, the last check is allowed-ips which either prevents or allows the traffic. + +To use a named key on an interface, the option private-key needs to be set. + +.. code-block:: sh + + set interfaces wireguard wg01 private-key KP01 + set interfaces wireguard wg02 private-key KP02 + +The command ``run show wireguard named-keypairs pubkey KP01`` will then show the public key, +which needs to be shared with the peer. + + **remote side** .. code-block:: sh @@ -99,11 +140,14 @@ your peer should have knowledge if its content. wg01# set interfaces wireguard wg01 peer to-wg02 preshared-key 'rvVDOoc2IYEnV+k5p7TNAmHBMEGTHbPU8Qqg8c/sUqc=' wg02# set interfaces wireguard wg01 peer to-wg01 preshared-key 'rvVDOoc2IYEnV+k5p7TNAmHBMEGTHbPU8Qqg8c/sUqc=' -**operational commands** +Operational commands +~~~~~~~~~~~~~~~~~~~~ + +**Show interface status** .. code-block:: sh - vyos@wg01# show interfaces wireguard wg01 + vyos@wg01# run show interfaces wireguard wg01 interface: wg01 public key: xHvgSJC8RTClfvjc0oX6OALxU6GGLapjthjw7x82CSw= @@ -115,3 +159,24 @@ your peer should have knowledge if its content. allowed ips: 10.2.0.0/24 latest handshake: 4 minutes, 22 seconds ago transfer: 860 B received, 948 B sent + +**Show public key of the default key** + +.. code-block:: sh + + vyos@wg01# run show wireguard keypair pubkey default + FAXCPb6EbTlSH5200J5zTopt9AYXneBthAySPBLbZwM= + +**Show public key of a named key** + +.. code-block:: sh + + vyos@wg01# run show wireguard keypair pubkey KP01 + HUtsu198toEnm1poGoRTyqkUKfKUdyh54f45dtcahDM= + + +**Delete wireguard keypairs** + +.. code-block:: sh + vyos@wg01# wireguard keypair default + |