diff options
Diffstat (limited to 'docs')
| -rw-r--r-- | docs/routing/ospf.rst | 73 |
1 files changed, 67 insertions, 6 deletions
diff --git a/docs/routing/ospf.rst b/docs/routing/ospf.rst index 563687de..23033bd6 100644 --- a/docs/routing/ospf.rst +++ b/docs/routing/ospf.rst @@ -3,13 +3,22 @@ Open Shortest Path First (OSPF) ------------------------------- -IPv4 -^^^^ +Open Shortest Path First (OSPF) is a routing protocol for Internet Protocol +(IP) networks. It uses a link state routing (LSR) algorithm and falls into the +group of interior gateway protocols (IGPs), operating within a single autonomous +system (AS). It is defined as OSPF Version 2 in RFC2328_ (1998) for IPv4. Updates +for IPv6 are specified as OSPF Version 3 in RFC5340_ (2008). OSPF supports the +Classless Inter-Domain Routing (CIDR) addressing model. + +OSPF is a widely used IGP in large enterprise networks. + +OSPFv2 (IPv4) +^^^^^^^^^^^^^ A typical configuration using 2 nodes, redistribute loopback address and the node 1 sending the default route: -**Node 1:** +**Node 1** .. code-block:: sh @@ -26,7 +35,7 @@ node 1 sending the default route: set policy route-map CONNECT rule 10 action permit set policy route-map CONNECT rule 10 match interface lo -**Node 2:** +**Node 2** .. code-block:: sh @@ -40,8 +49,8 @@ node 1 sending the default route: set policy route-map CONNECT rule 10 action permit set policy route-map CONNECT rule 10 match interface lo -IPv6 -^^^^ +OSPFv3 (IPv6) +^^^^^^^^^^^^^ A typical configuration using 2 nodes. @@ -63,3 +72,55 @@ A typical configuration using 2 nodes. set protocols ospfv3 parameters router-id 192.168.2.1 set protocols ospfv3 redistribute connected +.. note:: You can not easily redistribute IPv6 routes via OSPFv3 on a WireGuard + interface link. This requires you to configure link-local addresses manually + on the WireGuard interfaces, see Phabricator task T1483_. + +Example configuration for WireGuard interfaces: + +**Node 1** + +.. code-block:: sh + + set interfaces wireguard wg01 address 'fe80::216:3eff:fe51:fd8c/64' + set interfaces wireguard wg01 address '192.168.0.1/24' + set interfaces wireguard wg01 peer ospf02 allowed-ips '::/0' + set interfaces wireguard wg01 peer ospf02 allowed-ips '0.0.0.0/0' + set interfaces wireguard wg01 peer ospf02 endpoint '10.1.1.101:12345' + set interfaces wireguard wg01 peer ospf02 pubkey 'ie3...=' + set interfaces wireguard wg01 port '12345' + set protocols ospfv3 parameters router-id 192.168.1.1 + set protocols ospfv3 area 0.0.0.0 interface 'wg01' + set protocols ospfv3 area 0.0.0.0 interface 'lo' + +**Node 2** + +.. code-block:: sh + + set interfaces wireguard wg01 address 'fe80::216:3eff:fe0a:7ada/64' + set interfaces wireguard wg01 address '192.168.0.2/24' + set interfaces wireguard wg01 peer ospf01 allowed-ips '::/0' + set interfaces wireguard wg01 peer ospf01 allowed-ips '0.0.0.0/0' + set interfaces wireguard wg01 peer ospf01 endpoint '10.1.1.100:12345' + set interfaces wireguard wg01 peer ospf01 pubkey 'NHI...=' + set interfaces wireguard wg01 port '12345' + set protocols ospfv3 parameters router-id 192.168.1.2 + set protocols ospfv3 area 0.0.0.0 interface 'wg01' + set protocols ospfv3 area 0.0.0.0 interface 'lo' + +**Status** + +.. code-block:: sh + + vyos@ospf01:~$ sh ipv6 ospfv3 neighbor + Neighbor ID Pri DeadTime State/IfState Duration I/F[State] + 192.168.0.2 1 00:00:37 Full/PointToPoint 00:18:03 wg01[PointToPoint] + + vyos@ospf02# run sh ipv6 ospfv3 neighbor + Neighbor ID Pri DeadTime State/IfState Duration I/F[State] + 192.168.0.1 1 00:00:39 Full/PointToPoint 00:19:44 wg01[PointToPoint] + +.. _RFC2328: https://tools.ietf.org/html/rfc2328 +.. _RFC5340: https://tools.ietf.org/html/rfc2340 +.. _T1483: https://phabricator.vyos.net/T1483 + |