summaryrefslogtreecommitdiff
path: root/docs
diff options
context:
space:
mode:
Diffstat (limited to 'docs')
-rw-r--r--docs/configuration/protocols/igmp.rst23
1 files changed, 11 insertions, 12 deletions
diff --git a/docs/configuration/protocols/igmp.rst b/docs/configuration/protocols/igmp.rst
index 7109deb6..7f14b262 100644
--- a/docs/configuration/protocols/igmp.rst
+++ b/docs/configuration/protocols/igmp.rst
@@ -1,3 +1,5 @@
+:lastproofread: 2021-09-30
+
.. _multicast:
#########
@@ -99,7 +101,7 @@ These are the commands for a basic setup.
.. cfgcmd:: set protocols pim rp address <address> group
<multicast-address/mask-bits>
- Use this comand to manually configure a Rendevouz Point for PIM so
+ Use this command to manually configure a Rendezvous Point for PIM so
that join messages can be sent there. Set the Rendevouz Point address
and the matching prefix of group ranges covered. These values must
be shared with every router participating in the PIM network.
@@ -108,7 +110,7 @@ These are the commands for a basic setup.
.. cfgcmd:: set protocols igmp interface eth1
Use this command to configure an interface with IGMP so that PIM can
- receive IGMP reports and query on the selected interface. By defaul
+ receive IGMP reports and query on the selected interface. By default
IGMP version 3 will be used.
@@ -135,16 +137,16 @@ You can also tune multicast with the following commands.
.. cfgcmd:: set protocols pim rp keep-alive-timer <seconds>
- Use this PIM command to modify the the time out value (31-60000
+ Use this PIM command to modify the time out value (31-60000
seconds) for an `(S,G) <https://tools.ietf.org/html/rfc7761#section-4.1>`_
flow. 31 seconds is chosen for a lower bound as some hardware
- platforms cannot see data flowing in better than 30 second chunks.
+ platforms cannot see data flowing in better than 30 seconds chunks.
.. cfgcmd:: set protocols igmp interface <interface> join <multicast-address>
source <IP-address>
- Use this command to allow the selected interface join a multicast
+ Use this command to allow the selected interface to join a multicast
group defining the multicast address you want to join and the source
IP address too.
@@ -160,7 +162,7 @@ You can also tune multicast with the following commands.
Use this command to configure in the selected interface the IGMP
query response timeout value (10-250) in deciseconds. If a report is
- not returned in the specified time, it will be asumed the `(S,G) or
+ not returned in the specified time, it will be assumed the `(S,G) or
(*,G) state <https://tools.ietf.org/html/rfc7761#section-4.1>`_ has
timed out.
@@ -198,7 +200,7 @@ Configuration
.. cfgcmd:: set protocols igmp-proxy interface <interface> alt-subnet <network>
Defines alternate sources for multicasting and IGMP data. The network address
- must be on the following format 'a.b.c.d/n'. By default the router will
+ must be on the following format 'a.b.c.d/n'. By default, the router will
accept data from sources on the same network as configured on an interface.
If the multicast source lies on a remote network, one must define from where
traffic should be accepted.
@@ -213,10 +215,10 @@ Configuration
Disables quickleave mode. In this mode the daemon will not send a Leave IGMP
message upstream as soon as it receives a Leave message for any downstream
interface. The daemon will not ask for Membership reports on the downstream
- interfaces, and if a report is received the group is not joined again
+ interfaces, and if a report is received the group is not joined again the
upstream.
- If it's vital that the daemon should act exactly as a real multicast client
+ If it's vital that the daemon should act exactly like a real multicast client
on the upstream interface, this function should be enabled.
Enabling this function increases the risk of bandwidth saturation.
@@ -243,6 +245,3 @@ Operation
.. opcmd:: restart igmp-proxy
Restart the IGMP proxy process.
-
-
-