4 files changed, 28 insertions, 13 deletions
diff --git a/docs/configexamples/azure-vpn-bgp.rst b/docs/configexamples/azure-vpn-bgp.rst
index 176e0ae0..6f2622b2 100644
--- a/docs/configexamples/azure-vpn-bgp.rst
+++ b/docs/configexamples/azure-vpn-bgp.rst
@@ -6,7 +6,9 @@ Route-Based Site-to-Site VPN to Azure (BGP over IKEv2/IPsec)
 This guide shows an example of a route-based IKEv2 site-to-site VPN to
 Azure using VTI and BGP for dynamic routing updates.
 
-For redundant / active-active configurations see `Route-Based Redundant Site-to-Site VPN to Azure (BGP over IKEv2/IPsec) <https://docs.vyos.io/en/crux/appendix/examples/azure-vpn-dual-bgp.html>`_
+For redundant / active-active configurations see
+`Route-Based Redundant Site-to-Site VPN to Azure (BGP over IKEv2/IPsec)
+<https://docs.vyos.io/en/crux/appendix/examples/azure-vpn-dual-bgp.html>`_
 
 Prerequisites
 ^^^^^^^^^^^^^
diff --git a/docs/configexamples/dhcp-relay-through-gre-bridge.rst b/docs/configexamples/dhcp-relay-through-gre-bridge.rst
index f94eb67f..0db5fa0a 100644
--- a/docs/configexamples/dhcp-relay-through-gre-bridge.rst
+++ b/docs/configexamples/dhcp-relay-through-gre-bridge.rst
@@ -21,18 +21,18 @@ DHCP Server
 .. code-block:: none
 
    set interfaces ethernet eth0 address '10.0.2.1/24'
-   set interfaces loopback lo address '3.3.3.3/24'
+   set interfaces loopback lo address '192.168.3.3/24'
    set interfaces tunnel tun100 address '172.16.0.2/30'
    set interfaces tunnel tun100 encapsulation 'gre-bridge'
    set interfaces tunnel tun100 local-ip '10.0.2.1'
    set interfaces tunnel tun100 remote-ip '192.168.0.1'
-   set protocols ospf area 0 network '3.3.3.0/24'
+   set protocols ospf area 0 network '192.168.3.0/24'
    set protocols ospf area 0 network '10.0.2.0/24'
-   set protocols ospf parameters router-id '3.3.3.3'
+   set protocols ospf parameters router-id '192.168.3.3'
    set protocols static interface-route 10.0.1.2/32 next-hop-interface tun100
    set service dhcp-server shared-network-name asdf authoritative
-   set service dhcp-server shared-network-name asdf subnet 3.3.3.0/24 range 0 start '3.3.3.30'
-   set service dhcp-server shared-network-name asdf subnet 3.3.3.0/24 range 0 stop '3.3.3.40'
+   set service dhcp-server shared-network-name asdf subnet 192.168.3.0/24 range 0 start '192.168.3.30'
+   set service dhcp-server shared-network-name asdf subnet 192.168.3.0/24 range 0 stop '192.168.3.40'
    set service dhcp-server shared-network-name asdf subnet 10.0.1.0/24 default-router '10.0.1.2'
    set service dhcp-server shared-network-name asdf subnet 10.0.1.0/24 range 0 start '10.0.1.200'
    set service dhcp-server shared-network-name asdf subnet 10.0.1.0/24 range 0 stop '10.0.1.210'
@@ -61,17 +61,17 @@ DHCP Relay
 
    set interfaces ethernet eth0 address '10.0.1.2/24'
    set interfaces ethernet eth1 address '192.168.0.1/24'
-   set interfaces loopback lo address '1.1.1.1'
+   set interfaces loopback lo address '10.100.100.1'
    set interfaces tunnel tun100 address '172.16.0.1/30'
    set interfaces tunnel tun100 encapsulation 'gre-bridge'
    set interfaces tunnel tun100 local-ip '192.168.0.1'
    set interfaces tunnel tun100 remote-ip '10.0.2.1'
    set protocols ospf area 0 network '10.0.1.0/24'
    set protocols ospf area 0 network '192.168.0.0/24'
-   set protocols ospf area 0 network '1.1.1.0/24'
-   set protocols ospf parameters router-id '1.1.1.1'
-   set protocols static interface-route 3.3.3.3/32 next-hop-interface tun100
+   set protocols ospf area 0 network '10.100.100.0/24'
+   set protocols ospf parameters router-id '10.100.100.1'
+   set protocols static interface-route 192.168.3.3/32 next-hop-interface tun100
    set service dhcp-relay interface 'eth0'
    set service dhcp-relay interface 'tun100'
-   set service dhcp-relay server '3.3.3.3'
+   set service dhcp-relay server '192.168.3.3'
    
diff --git a/docs/configexamples/tunnelbroker-ipv6.rst b/docs/configexamples/tunnelbroker-ipv6.rst
index 868b225f..b6f1cc07 100644
--- a/docs/configexamples/tunnelbroker-ipv6.rst
+++ b/docs/configexamples/tunnelbroker-ipv6.rst
@@ -1,5 +1,7 @@
 .. _examples-tunnelbroker-ipv6:
 
+.. stop_vyoslinter
+
 #######################
 Tunnelbroker.net (IPv6)
 #######################
@@ -110,7 +112,9 @@ should be replaced with the information from your `Routed /64` tunnel):
   set service router-advert interface eth1 name-server '2001:4860:4860::8844'
   set service router-advert interface eth1 prefix 2001:470:xxxx:xxxx::/64 
 
-Please note, 'autonomous-flag' and 'on-link-flag' are enabled by default, 'valid-lifetime' and 'preferred-lifetime' are set to default values of 30 days and 4 hours respectively.
+Please note, 'autonomous-flag' and 'on-link-flag' are enabled by default,
+'valid-lifetime' and 'preferred-lifetime' are set to default values of
+30 days and 4 hours respectively.
 
 This accomplishes a few things:
 
@@ -155,7 +159,9 @@ So, when your LAN is eth1, your DMZ is eth2, your cameras live on eth3, etc:
   set service router-advert interface eth3 name-server '2001:4860:4860::8844'
   set service router-advert interface eth3 prefix 2001:470:xxxx:3::/64
 
-Please note, 'autonomous-flag' and 'on-link-flag' are enabled by default, 'valid-lifetime' and 'preferred-lifetime' are set to default values of 30 days and 4 hours respectively.
+Please note, 'autonomous-flag' and 'on-link-flag' are enabled by default,
+'valid-lifetime' and 'preferred-lifetime' are set to default values of
+30 days and 4 hours respectively.
 
 Firewall
 ========
@@ -167,3 +173,6 @@ NAME`.
 Similarly, to attach the firewall, you would use `set interfaces ethernet eth0
 firewall in ipv6-name` or `set zone-policy zone LOCAL from WAN firewall
 ipv6-name`.
+
+
+.. start_vyoslinter
diff --git a/docs/configexamples/wan-load-balancing.rst b/docs/configexamples/wan-load-balancing.rst
index 7093defe..07974166 100644
--- a/docs/configexamples/wan-load-balancing.rst
+++ b/docs/configexamples/wan-load-balancing.rst
@@ -1,5 +1,7 @@
 .. _wan-load-balancing:
 
+.. stop_vyoslinter # pictures and text have to change
+
 WAN Load Balancer examples
 ==========================
 
@@ -168,3 +170,5 @@ eth+ is used as an alias that refers to all ethernet interfaces:
    set load-balancing wan rule 5 exclude
    set load-balancing wan rule 5 inbound-interface eth+
    set load-balancing wan rule 5 destination address 10.0.0.0/8
+
+.. start_vyoslinter
+\ No newline at end of file