diff options
Diffstat (limited to 'docs')
| -rw-r--r-- | docs/configuration/vpn/dmvpn.rst | 2 | ||||
| -rw-r--r-- | docs/configuration/vpn/ipsec.rst | 58 | ||||
| -rw-r--r-- | docs/configuration/vpn/l2tp.rst | 111 | ||||
| -rw-r--r-- | docs/configuration/vpn/openconnect.rst | 4 | ||||
| -rw-r--r-- | docs/configuration/vpn/sstp.rst | 113 |
5 files changed, 157 insertions, 131 deletions
diff --git a/docs/configuration/vpn/dmvpn.rst b/docs/configuration/vpn/dmvpn.rst index 7a4b81f7..21df8cfd 100644 --- a/docs/configuration/vpn/dmvpn.rst +++ b/docs/configuration/vpn/dmvpn.rst @@ -162,7 +162,7 @@ Example This blueprint uses VyOS as the DMVPN Hub and Cisco (7206VXR) and VyOS as -multiple spoke sites. The lab was build using :abbr:`EVE-NG (Emulated Virtual +multiple spoke sites. The lab was built using :abbr:`EVE-NG (Emulated Virtual Environment NG)`. .. figure:: /_static/images/blueprint-dmvpn.png diff --git a/docs/configuration/vpn/ipsec.rst b/docs/configuration/vpn/ipsec.rst index c1ec645f..08282a44 100644 --- a/docs/configuration/vpn/ipsec.rst +++ b/docs/configuration/vpn/ipsec.rst @@ -13,10 +13,10 @@ address, which makes it easier to setup static routes or use dynamic routing protocols without having to modify IPsec policies. The other advantage is that it greatly simplifies router to router communication, which can be tricky with plain IPsec because the external outgoing address of the router usually doesn't -match the IPsec policy of typical site-to-site setup and you need to add special -configuration for it, or adjust the source address for outgoing traffic of your -applications. GRE/IPsec has no such problem and is completely transparent for -the applications. +match the IPsec policy of a typical site-to-site setup and you would need to +add special configuration for it, or adjust the source address of the outgoing +traffic of your applications. GRE/IPsec has no such problem and is completely +transparent for applications. GRE/IPIP/SIT and IPsec are widely accepted standards, which make this scheme easy to implement between VyOS and virtually any other router. @@ -163,13 +163,29 @@ Options (Global IPsec settings) Attributes * ``options`` - * ``disable-route-autoinstall`` Do not automatically install routes to remote networks; - - * ``flexvpn`` Allows FlexVPN vendor ID payload (IKEv2 only). Send the Cisco FlexVPN vendor ID payload (IKEv2 only), which is required in order to make Cisco brand devices allow negotiating a local traffic selector (from strongSwan's point of view) that is not the assigned virtual IP address if such an address is requested by strongSwan. Sending the Cisco FlexVPN vendor ID prevents the peer from narrowing the initiator's local traffic selector and allows it to e.g. negotiate a TS of 0.0.0.0/0 == 0.0.0.0/0 instead. This has been tested with a "tunnel mode ipsec ipv4" Cisco template but should also work for GRE encapsulation; - - * ``interface`` Interface Name to use. The name of the interface on which virtual IP addresses should be installed. If not specified the addresses will be installed on the outbound interface; - - * ``virtual-ip`` Allows to install virtual-ip addresses. Comma separated list of virtual IPs to request in IKEv2 configuration payloads or IKEv1 Mode Config. The wildcard addresses 0.0.0.0 and :: request an arbitrary address, specific addresses may be defined. The responder may return a different address, though, or none at all. Define the ``virtual-address`` option to configure the IP address in site-to-site hierarchy. + * ``disable-route-autoinstall`` Do not automatically install routes to remote + networks; + + * ``flexvpn`` Allows FlexVPN vendor ID payload (IKEv2 only). Send the Cisco + FlexVPN vendor ID payload (IKEv2 only), which is required in order to make + Cisco brand devices allow negotiating a local traffic selector (from + strongSwan's point of view) that is not the assigned virtual IP address if + such an address is requested by strongSwan. Sending the Cisco FlexVPN + vendor ID prevents the peer from narrowing the initiator's local traffic + selector and allows it to e.g. negotiate a TS of 0.0.0.0/0 == 0.0.0.0/0 + instead. This has been tested with a "tunnel mode ipsec ipv4" Cisco + template but should also work for GRE encapsulation; + + * ``interface`` Interface Name to use. The name of the interface on which + virtual IP addresses should be installed. If not specified the addresses + will be installed on the outbound interface; + + * ``virtual-ip`` Allows the installation of virtual-ip addresses. A comma + separated list of virtual IPs to request in IKEv2 configuration payloads or + IKEv1 Mode Config. The wildcard addresses 0.0.0.0 and :: request an + arbitrary address, specific addresses may be defined. The responder may + return a different address, or none at all. Define the ``virtual-address`` + option to configure the IP address in a site-to-site hierarchy. ************************* IPsec policy matching GRE @@ -372,8 +388,8 @@ IKEv2 IPSec road-warriors remote-access VPN ******************************************* Internet Key Exchange version 2, IKEv2 for short, is a request/response -protocol developed by both Cisco and Microsoft. It is used to establish -and secure IPv4/IPv6 connections, be it a site-to-site VPN or from a +protocol developed by both Cisco and Microsoft. It is used to establish and +secure IPv4/IPv6 connections, be it a site-to-site VPN or from a road-warrior connecting to a hub site. IKEv2, when run in point-to-multipoint, or remote-access/road-warrior mode, secures the server-side with another layer by using an x509 signed server certificate. @@ -396,11 +412,11 @@ This example uses CACert as certificate authority. set pki ca CAcert_Class_3_Root certificate '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' set pki ca CAcert_Signing_Authority certificate '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' -After you obtained your server certificate you can import it from a file -on the local filesystem, or paste it into the CLI. Please note that -when entering the certificate manually you need to strip the -``-----BEGIN KEY-----`` and ``-----END KEY-----`` tags. Also, the certificate -or key needs to be presented in a single line without line breaks (``\n``). +After you obtain your server certificate you can import it from a file on the +local filesystem, or paste it into the CLI. Please note that when entering the +certificate manually you need to strip the ``-----BEGIN KEY-----`` and +``-----END KEY-----`` tags. Also, the certificate or key needs to be presented +in a single line without line breaks (``\n``). To import it from the filesystem use: @@ -440,7 +456,7 @@ Every connection/remote-access pool we configure also needs a pool where we can draw our client IP addresses from. We provide one IPv4 and IPv6 pool. Authorized clients will receive an IPv4 address from the 192.0.2.128/25 prefix and an IPv6 address from the 2001:db8:2000::/64 prefix. We can also send some -DNS nameservers down to our clients used on their connection. +DNS nameservers down for our clients to use with their connection. .. code-block:: @@ -450,8 +466,8 @@ DNS nameservers down to our clients used on their connection. set vpn ipsec remote-access pool ra-rw-ipv6 prefix '2001:db8:2000::/64' VyOS supports multiple IKEv2 remote-access connections. Every connection can -have its dedicated IKE/ESP ciphers, certificates or local listen address for -e.g. inbound load balancing. +have its own dedicated IKE/ESP ciphers, certificates or local listen address +for e.g. inbound load balancing. We configure a new connection named ``rw`` for road-warrior, that identifies itself as ``192.0.2.1`` to the clients and uses the ``vyos`` certificate diff --git a/docs/configuration/vpn/l2tp.rst b/docs/configuration/vpn/l2tp.rst index b64c91a9..a0f5fb1b 100644 --- a/docs/configuration/vpn/l2tp.rst +++ b/docs/configuration/vpn/l2tp.rst @@ -148,15 +148,15 @@ For example: RADIUS source address ===================== -If you are using OSPF as IGP, always the closest interface connected to the -RADIUS server is used. With VyOS 1.2 you can bind all outgoing RADIUS requests -to a single source IP e.g. the loopback interface. +If you are using OSPF as your IGP, use the interface connected closest to the +RADIUS server. You can bind all outgoing RADIUS requests to a single source IP +e.g. the loopback interface. .. cfgcmd:: set vpn l2tp remote-access authentication radius source-address <address> Source IPv4 address used in all RADIUS server queires. -.. note:: The ``source-address`` must be configured on one of VyOS interface. +.. note:: The ``source-address`` must be configured to that of an interface. Best practice would be a loopback or dummy interface. RADIUS advanced options @@ -218,7 +218,7 @@ RADIUS advanced options The default attribute is `Filter-Id`. .. note:: If you set a custom RADIUS attribute you must define it on both - dictionaries at RADIUS server and client. + dictionaries on the RADIUS server and client. .. cfgcmd:: set vpn l2tp remote-access authentication radius rate-limit enable @@ -226,7 +226,7 @@ RADIUS advanced options .. cfgcmd:: set vpn l2tp remote-access authentication radius rate-limit vendor - Specifies the vendor dictionary, dictionary needs to be in + Specifies the vendor dictionary. This dictionary needs to be present in /usr/share/accel-ppp/radius. Received RADIUS attributes have a higher priority than parameters defined within @@ -236,25 +236,28 @@ Allocation clients ip addresses by RADIUS ========================================= If the RADIUS server sends the attribute ``Framed-IP-Address`` then this IP -address will be allocated to the client and the option ``default-pool`` within the CLI -config is being ignored. +address will be allocated to the client and the option ``default-pool`` within +the CLI config will be ignored. -If the RADIUS server sends the attribute ``Framed-Pool``, IP address will be allocated -from a predefined IP pool whose name equals the attribute value. +If the RADIUS server sends the attribute ``Framed-Pool``, then the IP address +will be allocated from a predefined IP pool whose name equals the attribute +value. -If the RADIUS server sends the attribute ``Stateful-IPv6-Address-Pool``, IPv6 address -will be allocated from a predefined IPv6 pool ``prefix`` whose name equals the attribute value. +If the RADIUS server sends the attribute ``Stateful-IPv6-Address-Pool``, the +IPv6 address will be allocated from a predefined IPv6 pool ``prefix`` whose +name equals the attribute value. -If the RADIUS server sends the attribute ``Delegated-IPv6-Prefix-Pool``, IPv6 -delegation pefix will be allocated from a predefined IPv6 pool ``delegate`` -whose name equals the attribute value. +If the RADIUS server sends the attribute ``Delegated-IPv6-Prefix-Pool``, an +IPv6 delegation prefix will be allocated from a predefined IPv6 pool +``delegate`` whose name equals the attribute value. .. note:: ``Stateful-IPv6-Address-Pool`` and ``Delegated-IPv6-Prefix-Pool`` are defined in RFC6911. If they are not defined in your RADIUS server, add new dictionary_. -User interface can be put to VRF context via RADIUS Access-Accept packet, or change -it via RADIUS CoA. ``Accel-VRF-Name`` is used from these purposes. It is custom `ACCEL-PPP attribute`_. -Define it in your RADIUS server. +The client's interface can be put into a VRF context via a RADIUS Access-Accept +packet, or changed via RADIUS CoA. ``Accel-VRF-Name`` is used for these +purposes. This is a custom `ACCEL-PPP attribute`_. Define it in your RADIUS +server. Renaming clients interfaces by RADIUS ===================================== @@ -296,19 +299,19 @@ IPv6 .. cfgcmd:: set vpn l2tp remote-access client-ipv6-pool <IPv6-POOL-NAME> prefix <address> mask <number-of-bits> - Use this comand to set the IPv6 address pool from which an l2tp client - will get an IPv6 prefix of your defined length (mask) to terminate the - l2tp endpoint at their side. The mask length can be set from 48 to 128 - bit long, the default value is 64. + Use this comand to set the IPv6 address pool from which an l2tp client will + get an IPv6 prefix of your defined length (mask) to terminate the l2tp + endpoint at their side. The mask length can be set between 48 and 128 bits + long, the default value is 64. .. cfgcmd:: set vpn l2tp remote-access client-ipv6-pool <IPv6-POOL-NAME> delegate <address> delegation-prefix <number-of-bits> - Use this command to configure DHCPv6 Prefix Delegation (RFC3633) on - l2tp. You will have to set your IPv6 pool and the length of the - delegation prefix. From the defined IPv6 pool you will be handing out - networks of the defined length (delegation-prefix). The length of the - delegation prefix can be set from 32 to 64 bit long. + Use this command to configure DHCPv6 Prefix Delegation (RFC3633) on l2tp. + You will have to set your IPv6 pool and the length of the delegation + prefix. From the defined IPv6 pool you will be handing out networks of the + defined length (delegation-prefix). The length of the delegation prefix can + be between 32 and 64 bits long. .. cfgcmd:: set vpn l2tp remote-access default-ipv6-pool <IPv6-POOL-NAME> @@ -325,19 +328,19 @@ IPv6 Advanced Options ===================== .. cfgcmd:: set vpn l2tp remote-access ppp-options ipv6-accept-peer-interface-id - Accept peer interface identifier. By default is not defined. + Accept peer interface identifier. By default this is not defined. .. cfgcmd:: set vpn l2tp remote-access ppp-options ipv6-interface-id <random | x:x:x:x> - Specifies fixed or random interface identifier for IPv6. - By default is fixed. + Specifies if a fixed or random interface identifier is used for IPv6. The + default is fixed. * **random** - Random interface identifier for IPv6 * **x:x:x:x** - Specify interface identifier for IPv6 .. cfgcmd:: set vpn l2tp remote-access ppp-options ipv6-interface-id <random | x:x:x:x> - Specifies peer interface identifier for IPv6. By default is fixed. + Specifies the peer interface identifier for IPv6. The default is fixed. * **random** - Random interface identifier for IPv6 * **x:x:x:x** - Specify interface identifier for IPv6 @@ -350,19 +353,19 @@ Scripting .. cfgcmd:: set vpn l2tp remote-access extended-scripts on-change <path_to_script> - Script to run when session interface changed by RADIUS CoA handling + Script to run when the session interface is changed by RADIUS CoA handling .. cfgcmd:: set vpn l2tp remote-access extended-scripts on-down <path_to_script> - Script to run when session interface going to terminate + Script to run when the session interface is about to terminate .. cfgcmd:: set vpn l2tp remote-access extended-scripts on-pre-up <path_to_script> - Script to run before session interface comes up + Script to run before the session interface comes up .. cfgcmd:: set vpn l2tp remote-access extended-scripts on-up <path_to_script> - Script to run when session interface is completely configured and started + Script to run when the session interface is completely configured and started **************** Advanced Options @@ -378,17 +381,17 @@ Authentication Advanced Options .. cfgcmd:: set vpn l2tp remote-access authentication local-users username <user> static-ip <address> - Assign static IP address to `<user>` account. + Assign a static IP address to `<user>` account. .. cfgcmd:: set vpn l2tp remote-access authentication local-users username <user> rate-limit download <bandwidth> - Download bandwidth limit in kbit/s for `<user>`. + Rate limit the download bandwidth for `<user>` to `<bandwidth>` kbit/s. .. cfgcmd:: set vpn l2tp remote-access authentication local-users username <user> rate-limit upload <bandwidth> - Upload bandwidth limit in kbit/s for `<user>`. + Rate limit the upload bandwidth for `<user>` to `<bandwidth>` kbit/s .. cfgcmd:: set vpn l2tp remote-access authentication protocols <pap | chap | mschap | mschap-v2> @@ -413,10 +416,10 @@ PPP Advanced Options .. cfgcmd:: set vpn l2tp remote-access ppp-options interface-cache <number> - Specifies number of interfaces to keep in cache. It means that don’t - destroy interface after corresponding session is destroyed, instead - place it to cache and use it later for new sessions repeatedly. - This should reduce kernel-level interface creation/deletion rate lack. + Specifies number of interfaces to cache. This prevents interfaces from being + removed once the corresponding session is destroyed. Instead, interfaces are + cached for later use in new sessions. This should reduce the kernel-level + interface creation/deletion rate. Default value is **0**. .. cfgcmd:: set vpn l2tp remote-access ppp-options ipv4 <require | prefer | allow | deny> @@ -436,19 +439,20 @@ PPP Advanced Options .. cfgcmd:: set vpn l2tp remote-access ppp-options lcp-echo-interval <interval> If this option is specified and is greater than 0, then the PPP module will - send LCP pings of the echo request every `<interval>` seconds. + send LCP echo requests every `<interval>` seconds. Default value is **30**. .. cfgcmd:: set vpn l2tp remote-access ppp-options lcp-echo-timeout - Specifies timeout in seconds to wait for any peer activity. If this option + Specifies timeout in seconds to wait for any peer activity. If this option is specified it turns on adaptive lcp echo functionality and "lcp-echo-failure" is not used. Default value is **0**. .. cfgcmd:: set vpn l2tp remote-access ppp-options min-mtu <number> - Defines minimum acceptable MTU. If client will try to negotiate less then - specified MTU then it will be NAKed or disconnected if rejects greater MTU. + Defines the minimum acceptable MTU. If a client tries to negotiate an MTU + lower than this it will be NAKed, and disconnected if it rejects a greater + MTU. Default value is **100**. .. cfgcmd:: set vpn l2tp remote-access ppp-options mppe <require | prefer | deny> @@ -460,9 +464,10 @@ PPP Advanced Options * **prefer** - ask client for mppe, if it rejects don't fail. (Default value) * **deny** - deny mppe - Default behavior - don't ask client for mppe, but allow it if client wants. - Please note that RADIUS may override this option by MS-MPPE-Encryption-Policy - attribute. + Default behavior - don't ask the client for mppe, but allow it if the client + wants. + Please note that RADIUS may override this option with the + MS-MPPE-Encryption-Policy attribute. .. cfgcmd:: set vpn l2tp remote-access ppp-options mru <number> @@ -481,7 +486,7 @@ Global Advanced options .. cfgcmd:: set vpn l2tp remote-access limits connection-limit <value> - Acceptable rate of connections (e.g. 1/min, 60/sec) + Maximum accepted connection rate (e.g. 1/min, 60/sec) .. cfgcmd:: set vpn l2tp remote-access limits timeout <value> @@ -497,9 +502,9 @@ Global Advanced options .. cfgcmd:: set vpn l2tp remote-access name-server <address> - Connected client should use `<address>` as their DNS server. This - command accepts both IPv4 and IPv6 addresses. Up to two nameservers - can be configured for IPv4, up to three for IPv6. + Connected clients should use `<address>` as their DNS server. This command + accepts both IPv4 and IPv6 addresses. Up to two nameservers can be configured + for IPv4, up to three for IPv6. .. cfgcmd:: set vpn l2tp remote-access shaper fwmark <1-2147483647> diff --git a/docs/configuration/vpn/openconnect.rst b/docs/configuration/vpn/openconnect.rst index 845d9196..09d0574d 100644 --- a/docs/configuration/vpn/openconnect.rst +++ b/docs/configuration/vpn/openconnect.rst @@ -4,7 +4,7 @@ OpenConnect ########### -OpenConnect-compatible server feature is available from this release. +OpenConnect-compatible server feature has been available since Equuleus (1.3). Openconnect VPN supports SSL connection and offers full network access. SSL VPN network extension connects the end-user system to the corporate network with access controls based only on network layer information, such as destination IP @@ -32,7 +32,7 @@ will create a self signed certificates and will be stored in configuration: run generate pki ca install <CA name> run generate pki certificate sign <CA name> install <Server name> -We can also create the certificates using Cerbort which is an easy-to-use +We can also create the certificates using Certbot which is an easy-to-use client that fetches a certificate from Let's Encrypt an open certificate authority launched by the EFF, Mozilla, and others and deploys it to a web server. diff --git a/docs/configuration/vpn/sstp.rst b/docs/configuration/vpn/sstp.rst index cd064162..e750cdcf 100644 --- a/docs/configuration/vpn/sstp.rst +++ b/docs/configuration/vpn/sstp.rst @@ -16,8 +16,8 @@ SSTP is available for Linux, BSD, and Windows. VyOS utilizes accel-ppp_ to provide SSTP server functionality. We support both local and RADIUS authentication. -As SSTP provides PPP via a SSL/TLS channel the use of either publically signed -certificates as well as a private PKI is required. +As SSTP provides PPP via a SSL/TLS channel the use of either publicly signed +certificates or private PKI is required. *********************** Configuring SSTP Server @@ -92,8 +92,8 @@ Configuring RADIUS authentication ********************************* To enable RADIUS based authentication, the authentication mode needs to be -changed within the configuration. Previous settings like the local users, still -exists within the configuration, however they are not used if the mode has been +changed within the configuration. Previous settings like the local users still +exist within the configuration, however they are not used if the mode has been changed from local to radius. Once changed back to local, it will use all local accounts again. @@ -121,15 +121,15 @@ For example: RADIUS source address ===================== -If you are using OSPF as IGP, always the closest interface connected to the -RADIUS server is used. You can bind all outgoing RADIUS requests -to a single source IP e.g. the loopback interface. +If you are using OSPF as your IGP, use the interface connected closest to the +RADIUS server. You can bind all outgoing RADIUS requests to a single source IP +e.g. the loopback interface. .. cfgcmd:: set vpn sstp authentication radius source-address <address> Source IPv4 address used in all RADIUS server queires. -.. note:: The ``source-address`` must be configured on one of VyOS interface. +.. note:: The ``source-address`` must be configured to that of an interface. Best practice would be a loopback or dummy interface. RADIUS advanced options @@ -191,7 +191,7 @@ RADIUS advanced options The default attribute is `Filter-Id`. .. note:: If you set a custom RADIUS attribute you must define it on both - dictionaries at RADIUS server and client. + dictionaries on the RADIUS server and client. .. cfgcmd:: set vpn sstp authentication radius rate-limit enable @@ -199,7 +199,7 @@ RADIUS advanced options .. cfgcmd:: set vpn sstp authentication radius rate-limit vendor - Specifies the vendor dictionary, dictionary needs to be in + Specifies the vendor dictionary, This dictionary needs to be present in /usr/share/accel-ppp/radius. Received RADIUS attributes have a higher priority than parameters defined within @@ -209,25 +209,28 @@ Allocation clients ip addresses by RADIUS ========================================= If the RADIUS server sends the attribute ``Framed-IP-Address`` then this IP -address will be allocated to the client and the option ``default-pool`` within the CLI -config is being ignored. +address will be allocated to the client and the option ``default-pool`` within +the CLI config will being ignored. -If the RADIUS server sends the attribute ``Framed-Pool``, IP address will be allocated -from a predefined IP pool whose name equals the attribute value. +If the RADIUS server sends the attribute ``Framed-Pool``, then the IP address +will be allocated from a predefined IP pool whose name equals the attribute +value. -If the RADIUS server sends the attribute ``Stateful-IPv6-Address-Pool``, IPv6 address -will be allocated from a predefined IPv6 pool ``prefix`` whose name equals the attribute value. +If the RADIUS server sends the attribute ``Stateful-IPv6-Address-Pool``, the +IPv6 address will be allocated from a predefined IPv6 pool ``prefix`` whose +name equals the attribute value. -If the RADIUS server sends the attribute ``Delegated-IPv6-Prefix-Pool``, IPv6 -delegation pefix will be allocated from a predefined IPv6 pool ``delegate`` +If the RADIUS server sends the attribute ``Delegated-IPv6-Prefix-Pool``, an +IPv6 delegation prefix will be allocated from a predefined IPv6 pool ``delegate`` whose name equals the attribute value. .. note:: ``Stateful-IPv6-Address-Pool`` and ``Delegated-IPv6-Prefix-Pool`` are defined in RFC6911. If they are not defined in your RADIUS server, add new dictionary_. -User interface can be put to VRF context via RADIUS Access-Accept packet, or change -it via RADIUS CoA. ``Accel-VRF-Name`` is used from these purposes. It is custom `ACCEL-PPP attribute`_. -Define it in your RADIUS server. +The client's interface can be put into a VRF context via a RADIUS Access-Accept +packet, or changed via RADIUS CoA. ``Accel-VRF-Name`` is used for these +purposes. This is a custom `ACCEL-PPP attribute`_. Define it in your RADIUS +server. Renaming clients interfaces by RADIUS ===================================== @@ -254,19 +257,19 @@ IPv6 .. cfgcmd:: set vpn sstp client-ipv6-pool <IPv6-POOL-NAME> prefix <address> mask <number-of-bits> - Use this comand to set the IPv6 address pool from which an SSTP client - will get an IPv6 prefix of your defined length (mask) to terminate the - SSTP endpoint at their side. The mask length can be set from 48 to 128 - bit long, the default value is 64. + Use this comand to set the IPv6 address pool from which an SSTP client will + get an IPv6 prefix of your defined length (mask) to terminate the SSTP + endpoint at their side. The mask length can be set between 48 and 128 bits + long, the default value is 64. .. cfgcmd:: set vpn sstp client-ipv6-pool <IPv6-POOL-NAME> delegate <address> delegation-prefix <number-of-bits> - Use this command to configure DHCPv6 Prefix Delegation (RFC3633) on - SSTP. You will have to set your IPv6 pool and the length of the - delegation prefix. From the defined IPv6 pool you will be handing out - networks of the defined length (delegation-prefix). The length of the - delegation prefix can be set from 32 to 64 bit long. + Use this command to configure DHCPv6 Prefix Delegation (RFC3633) on SSTP. You + will have to set your IPv6 pool and the length of the delegation prefix. From + the defined IPv6 pool you will be handing out networks of the defined length + (delegation-prefix). The length of the delegation prefix can be set between + 32 and 64 bits long. .. cfgcmd:: set vpn sstp default-ipv6-pool <IPv6-POOL-NAME> @@ -283,19 +286,19 @@ IPv6 Advanced Options ===================== .. cfgcmd:: set vpn sstp ppp-options ipv6-accept-peer-interface-id - Accept peer interface identifier. By default is not defined. + Accept peer interface identifier. By default this is not defined. .. cfgcmd:: set vpn sstp ppp-options ipv6-interface-id <random | x:x:x:x> - Specifies fixed or random interface identifier for IPv6. - By default is fixed. + Specifies if a fixed or random interface identifier is used for IPv6. The + default is fixed. * **random** - Random interface identifier for IPv6 * **x:x:x:x** - Specify interface identifier for IPv6 .. cfgcmd:: set vpn sstp ppp-options ipv6-interface-id <random | x:x:x:x> - Specifies peer interface identifier for IPv6. By default is fixed. + Specifies the peer interface identifier for IPv6. The default is fixed. * **random** - Random interface identifier for IPv6 * **x:x:x:x** - Specify interface identifier for IPv6 @@ -308,19 +311,19 @@ Scripting .. cfgcmd:: set vpn sstp extended-scripts on-change <path_to_script> - Script to run when session interface changed by RADIUS CoA handling + Script to run when the session interface is changed by RADIUS CoA handling .. cfgcmd:: set vpn sstp extended-scripts on-down <path_to_script> - Script to run when session interface going to terminate + Script to run when the session interface about to terminate .. cfgcmd:: set vpn sstp extended-scripts on-pre-up <path_to_script> - Script to run before session interface comes up + Script to run before the session interface comes up .. cfgcmd:: set vpn sstp extended-scripts on-up <path_to_script> - Script to run when session interface is completely configured and started + Script to run when the session interface is completely configured and started **************** Advanced Options @@ -336,17 +339,17 @@ Authentication Advanced Options .. cfgcmd:: set vpn sstp authentication local-users username <user> static-ip <address> - Assign static IP address to `<user>` account. + Assign a static IP address to `<user>` account. .. cfgcmd:: set vpn sstp authentication local-users username <user> rate-limit download <bandwidth> - Download bandwidth limit in kbit/s for `<user>`. + Rate limit the download bandwidth for `<user>` to `<bandwidth>` kbit/s. .. cfgcmd:: set vpn sstp authentication local-users username <user> rate-limit upload <bandwidth> - Upload bandwidth limit in kbit/s for `<user>`. + Rate limit the upload bandwidth for `<user>` to `<bandwidth>` kbit/s. .. cfgcmd:: set vpn sstp authentication protocols <pap | chap | mschap | mschap-v2> @@ -371,10 +374,10 @@ PPP Advanced Options .. cfgcmd:: set vpn sstp ppp-options interface-cache <number> - Specifies number of interfaces to keep in cache. It means that don’t - destroy interface after corresponding session is destroyed, instead - place it to cache and use it later for new sessions repeatedly. - This should reduce kernel-level interface creation/deletion rate lack. + Specifies number of interfaces to cache. This prevents interfaces from being + removed once the corresponding session is destroyed. Instead, interfaces are + cached for later use in new sessions. This should reduce the kernel-level + interface creation/deletion rate. Default value is **0**. .. cfgcmd:: set vpn sstp ppp-options ipv4 <require | prefer | allow | deny> @@ -394,19 +397,20 @@ PPP Advanced Options .. cfgcmd:: set vpn sstp ppp-options lcp-echo-interval <interval> If this option is specified and is greater than 0, then the PPP module will - send LCP pings of the echo request every `<interval>` seconds. + send LCP echo requests every `<interval>` seconds. Default value is **30**. .. cfgcmd:: set vpn sstp ppp-options lcp-echo-timeout - Specifies timeout in seconds to wait for any peer activity. If this option + Specifies timeout in seconds to wait for any peer activity. If this option is specified it turns on adaptive lcp echo functionality and "lcp-echo-failure" is not used. Default value is **0**. .. cfgcmd:: set vpn sstp ppp-options min-mtu <number> - Defines minimum acceptable MTU. If client will try to negotiate less then - specified MTU then it will be NAKed or disconnected if rejects greater MTU. + Defines the minimum acceptable MTU. If a client tries to negotiate an MTU + lower than this it will be NAKed, and disconnected if it rejects a greater + MTU. Default value is **100**. .. cfgcmd:: set vpn sstp ppp-options mppe <require | prefer | deny> @@ -418,7 +422,8 @@ PPP Advanced Options * **prefer** - ask client for mppe, if it rejects don't fail. (Default value) * **deny** - deny mppe - Default behavior - don't ask client for mppe, but allow it if client wants. + Default behavior - don't ask the client for mppe, but allow it if the client + wants. Please note that RADIUS may override this option by MS-MPPE-Encryption-Policy attribute. @@ -439,7 +444,7 @@ Global Advanced options .. cfgcmd:: set vpn sstp limits connection-limit <value> - Acceptable rate of connections (e.g. 1/min, 60/sec) + Maximum accepted connection rate (e.g. 1/min, 60/sec) .. cfgcmd:: set vpn sstp limits timeout <value> @@ -455,9 +460,9 @@ Global Advanced options .. cfgcmd:: set vpn sstp name-server <address> - Connected client should use `<address>` as their DNS server. This - command accepts both IPv4 and IPv6 addresses. Up to two nameservers - can be configured for IPv4, up to three for IPv6. + Connected clients should use `<address>` as their DNS server. This command + accepts both IPv4 and IPv6 addresses. Up to two nameservers can be configured + for IPv4, up to three for IPv6. .. cfgcmd:: set vpn sstp shaper fwmark <1-2147483647> |