From c061829d260eef67786e0972b4cac0b3caac52ac Mon Sep 17 00:00:00 2001 From: srividya0208 Date: Wed, 18 Aug 2021 12:58:46 -0400 Subject: grammar & spelling correction --- docs/cli.rst | 38 +++++++++++++++++++++----------------- 1 file changed, 21 insertions(+), 17 deletions(-) (limited to 'docs/cli.rst') diff --git a/docs/cli.rst b/docs/cli.rst index d5f00a45..4a219eba 100644 --- a/docs/cli.rst +++ b/docs/cli.rst @@ -1,3 +1,5 @@ +:lastproofread: 2021-08-16 + .. _cli: ###################### @@ -12,7 +14,8 @@ Operational Mode Operational mode allows for commands to perform operational system tasks and view system and service status, while configuration mode allows for the -modification of system configuration. The :ref:`command tree page` lists available commands and their functions. +modification of system configuration. The :ref:`command tree page` +lists available commands and their functions. The CLI provides a built-in help system. In the CLI the **[?]** key may be used to display available commands. The **[tab]** key can be used to auto-complete @@ -57,7 +60,8 @@ Example showing possible show commands: : q vyos@vyos:~$ -You can scroll up with the keys [Shift]+[PageUp] and sroll down with [Shift]+[PageDown]. +You can scroll up with the keys [Shift]+[PageUp] and scroll down with [Shift]+ +[PageDown]. When the output of a command results in more lines than can be displayed on the terminal screen the output is paginated as indicated by a : prompt. @@ -83,7 +87,8 @@ To enter configuration mode use the `configure` command: [edit] vyos@vyos:~# -.. note:: Prompt changes from `$` to `#`. To exit configuration mode, type `exit`. +.. note:: Prompt changes from `$` to `#`. To exit configuration mode, type +`exit`. .. code-block:: none @@ -265,7 +270,7 @@ command. You are now in a sublevel relative to ``interfaces ethernet eth0``, all commands executed from this point on are relative to this sublevel. Use -eithe the :cfgcmd:`top` or :cfgcmd:`exit` command to go back to the top +either the :cfgcmd:`top` or :cfgcmd:`exit` command to go back to the top of the hierarchy. You can also use the :cfgcmd:`up` command to move only one level up at a time. @@ -454,8 +459,8 @@ different levels in the hierarchy. What if you are doing something dangerous? Suppose you want to setup a firewall, and you are not sure there are no mistakes that will lock you out of your system. You can use confirmed commit. If you issue - the ``commit-confirm`` command, your changes will be commited, and if - you don't issue issue the ``confirm`` command in 10 minutes, your + the ``commit-confirm`` command, your changes will be committed, and if + you don't issue the ``confirm`` command in 10 minutes, your system will reboot into previous config revision. .. code-block:: none @@ -469,9 +474,9 @@ different levels in the hierarchy. [edit] - .. note:: A reboot because you did not enter ``confirm`` will not - take you necessarily to the *saved configuration*, but to the - point before the unfortunate commit. + .. note:: A reboot will be initiated if you did not enter ``confirm`` + and will take you necessarily to the last *saved configuration*, but to + the point before the unfortunate commit. .. cfgcmd:: copy @@ -481,9 +486,8 @@ different levels in the hierarchy. You can copy and remove configuration subtrees. Suppose you set up a firewall ruleset ``FromWorld`` with one rule that allows traffic from specific subnet. Now you want to setup a similar rule, but for - different subnet. Change your edit level to - ``firewall name FromWorld`` and use ``copy rule 10 to rule 20``, then - modify rule 20. + different subnet. Change your edit level to``firewall name FromWorld`` and + use ``copy rule 10 to rule 20``, then modify rule 20. .. code-block:: none @@ -549,7 +553,7 @@ different levels in the hierarchy. The ``comment`` command allows you to insert a comment above the ```` configuration section. When shown, comments are enclosed with ``/*`` and ``*/`` as open/close delimiters. Comments - need to be commited, just like other config changes. + need to be committed, just like other config changes. To remove an existing comment from your current configuration, specify an empty string enclosed in double quote marks (``""``) as @@ -671,7 +675,7 @@ VyOS lets you compare different configurations. 7 2013-12-12 16:25:19 vyos by cli 8 2013-12-12 15:44:36 vyos by cli 9 2013-12-12 15:42:07 root by boot-config-loader - 10 2013-12-12 15:42:06 root by init + 10 2013-12-12 15:42:06 root by init The command :cfgcmd:`compare` allows you to compare different type of configurations. It also lets you compare different revisions through @@ -720,7 +724,7 @@ Rollback Changes ================ You can rollback configuration changes using the rollback command. This -will apply the selected revision and trigger a system reboot. +will apply to the selected revision and trigger a system reboot. .. cfgcmd:: rollback @@ -783,8 +787,8 @@ to load it with the ``load`` command: Use this command to load a configuration which will replace the running configuration. Define the location of the configuration file - to be loaded. You can use a path to a local file, an SCP address, an - SFTP address, an FTP address, an HTTP address, an HTTPS address or a + to be loaded. You can use a path to a local file, a SCP address, a + SFTP address, a FTP address, a HTTP address, a HTTPS address or a TFTP address. .. code-block:: none -- cgit v1.2.3