From c44aa8aeac5b3b279d2aca60e3d2bbe74565c2fe Mon Sep 17 00:00:00 2001
From: Cheeze_It <none@none.com>
Date: Mon, 19 Oct 2020 19:42:40 -0600
Subject: MPLS: fix conf-mode definitions and line breaks

Moved the configuration mode commands and descriptions to fit VyOS template.
---
 docs/routing/mpls.rst | 30 +++++++++++++++---------------
 1 file changed, 15 insertions(+), 15 deletions(-)

(limited to 'docs')

diff --git a/docs/routing/mpls.rst b/docs/routing/mpls.rst
index 0ae6094c..86221104 100644
--- a/docs/routing/mpls.rst
+++ b/docs/routing/mpls.rst
@@ -37,7 +37,7 @@ For more information on how MPLS label switching works, please go visit
 Label Distribution Protocol
 ===========================
 
-The :abbr: `MPLS (Multi-Protocol Label Switching)` architecture does not assume
+The :abbr:`MPLS (Multi-Protocol Label Switching)` architecture does not assume
 a single protocol to create MPLS paths. VyOS supports the Label Distribution
 Protocol (LDP) as implemented by FRR, based on :rfc:`5036`.
 
@@ -61,44 +61,44 @@ must be explicitly set in the configuration.
 Configuration Options
 =====================
 
-Use this command to enable LDP, and enable MPLS processing on the interface you
-define.
-
 .. cfgcmd:: set protocols mpls ldp interface <interface>
 
-  Use this command to configure the IP address used as the LDP router-id of the
-  local device.
+  Use this command to enable LDP, and enable MPLS processing on the interface you
+  define.
 
 .. cfgcmd:: set protocols mpls ldp router-id <address>
 
-  Use this command to set the IPv4 or IPv6 transport-address used by LDP.
+  Use this command to configure the IP address used as the LDP router-id of the
+  local device.
 
 .. cfgcmd:: set protocols mpls ldp discovery transport-ipv4-address <IPv4 address>
 .. cfgcmd:: set protocols mpls ldp discovery transport-ipv6-address <IPv6 address>
 
-  Use this command to configure authentication for LDP peers. Set the
-  IP address of the LDP peer and a password that should be shared in
-  order to become neighbors.
+  Use this command to set the IPv4 or IPv6 transport-address used by LDP.
 
 .. cfgcmd:: set protocols mpls ldp neighbor <IPv4 address> password <password>
 
-  Use this command if you would like to set the discovery hello and hold time
-  parameters.
+  Use this command to configure authentication for LDP peers. Set the
+  IP address of the LDP peer and a password that should be shared in
+  order to become neighbors.
 
 .. cfgcmd:: set protocols mpls ldp discovery hello-interval <seconds>
 .. cfgcmd:: set protocols mpls ldp discovery hello-holdtime <seconds>
 
-Use this command if you would like to set the TCP session hold time intervals.
+  Use this command if you would like to set the discovery hello and hold time
+  parameters.
 
 .. cfgcmd:: set protocols mpls ldp discovery session-ipv4-holdtime <seconds>
 .. cfgcmd:: set protocols mpls ldp discovery session-ipv6-holdtime <seconds>
 
-Use this command if you would like for the router to advertise FECs with a label
-of 0 for explicit null operations.
+  Use this command if you would like to set the TCP session hold time intervals.
 
 .. cfgcmd:: set protocols mpls ldp export ipv4 explicit-null
 .. cfgcmd:: set protocols mpls ldp export ipv6 explicit-null
 
+  Use this command if you would like for the router to advertise FECs with a label
+  of 0 for explicit null operations.
+
 
 Sample configuration to setup LDP on VyOS
 -----------------------------------------
-- 
cgit v1.2.3