################################ Inter-VRF Routing over VRF Lite ################################ **Virtual Routing and Forwarding** is a technology that allow multiple instance of a routing table to exist within a single device. One of the key aspect of **VRFs** is that do not share the same routes or interfaces, therefore packets are forwarded between interfaces that belong to the same VRF only. Any information related to a VRF is not exchanged between devices -or in the same device- by default, this is a technique called **VRF-Lite**. Keep networks isolated is -in general- a good principle, but there are cases where you might need that some network can access other in a different VRF. The scope of this document is to cover such cases in a dynamic way without the use of MPLS-LDP. General information about L3VPNs can be found in the :ref:`configuration/vrf/index:L3VPN VRFs` chapter. ******** Overview ******** Let’s say we have a requirement to have multiple networks. * LAN 1 * LAN 2 * Management * Internet Both LANs have to be able to route between each other, both will have managed devices through a dedicated management network and both will need Internet access yet the LAN2 will need access to some set of outside networks, not all. The management network will need access to both LANs but cannot have access to/from the outside. This scenario could be a nightmare applying regular routing and might need filtering in multiple interfaces. A simple solution could be using different routing tables, or VRFs for all the networks so we can keep the routing restrictions. But for us to route between the different VRFs we would need a cable or a logical connection between each other: * One cable/logical connection between LAN1 and LAN2 * One cable/logical connection between LAN1 and Internet * One cable/logical connection between LAN2 and Internet * One cable/logical connection between LAN1 and Management * One cable/logical connection between LAN2 and Management As we can see this is unpractical. To address this scenario we will use to our advantage an extension of the BGP routing protocol that will help us in the “Export” between VRFs without the need for MPLS. MP-BGP or MultiProtocol BGP introduces two main concepts to solve this limitation: - Route Distinguisher (RD): Is used to distinguish between different VRFs –called VPNs- inside the BGP Process. The RD is appended to each IPv4 Network that is advertised into BGP for that VPN making it a unique VPNv4 route. - Route Target (RT): This is an extended BGP community append to the VPNv4 route in the Import/Export process. When a route passes from the VRF routing table into the BGP process it will add the configured export extended community(ies) for that VPN. When that route needs to go from BGP into the VRF routing table will only pass if that given VPN import policy matches any of the appended community(ies) into that prefix. ******** Topology ******** .. image:: /_static/images/inter-vrf-routing-vrf-lite.png :width: 70% :align: center :alt: Network Topology Diagram IP Schema ========= +----------+------------+----------------+------------------+ | Device-A | Device-B | IPv4 Network | IPv6 Network | +----------+------------+----------------+------------------+ | Core | LAN1 | 10.1.1.0/30 | 2001:db8::/127 | +----------+------------+----------------+------------------+ | Core | LAN2 | 172.16.2.0/30 | 2001:db8::2/127 | +----------+------------+----------------+------------------+ | Core | Management | 192.168.3.0/30 | 2001:db8::4/127 | +----------+------------+----------------+------------------+ | Core | ISP | 10.2.2.0/30 | 2001:db8::6/127 | +----------+------------+----------------+------------------+ RD & RT Schema ============== +------------+-----------+-----------+ | VRF | RD | RT | +------------+-----------+-----------+ | LAN1 | 64496:1 | 64496:1 | +------------+-----------+-----------+ | LAN2 | 64496:2 | 64496:2 | +------------+-----------+-----------+ | Management | 64496:50 | 64496:50 | +------------+-----------+-----------+ | Internet | 64496:100 | 64496:100 | +------------+-----------+-----------+ ************** Configurations ************** .. note:: We use a static route configuration in between the Core and each LAN and Management router, and BGP between the Core router and the ISP router but any dynamic routing protocol can be used. Remote Networks =============== The following template configuration can be used in each remote router based in our topology. .. code-block:: none # Interface Configuration set interface eth eth address # Static default route back to Core set procotols static route 0.0.0.0/0 next-hop Core Router =========== Step 1: VRF and Configurations to remote networks ------------------------------------------------- - Configuration Set the VRF name and Table ID, set interface address and bind it to the VRF. Last add the static route to the remote network. .. code-block:: none # VRF name and table ID (MANDATORY) set vrf name table # Interface Configuration set interface eth eth address # Assign interface to VRF set interface eth eth vrf # Static route to remote Network set vrf name protocols static route next-hop - Verification Checking the routing table of the VRF should reveal both static and connected entries active. A PING test between the Core and remote router is a way to validate connectivity within the VRF. .. code-block:: none # show ip route vrf # show ipv6 route vrf vyos@Core:~$ show ip route vrf LAN1 Codes: K - kernel route, C - connected, S - static, R - RIP, O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP, T - Table, v - VNC, V - VNC-Direct, A - Babel, F - PBR, f - OpenFabric, > - selected route, * - FIB route, q - queued, r - rejected, b - backup t - trapped, o - offload failure VRF LAN1: S>* 10.0.0.0/24 [1/0] via 10.1.1.2, eth0, weight 1, 00:05:41 C>* 10.1.1.0/30 is directly connected, eth0, 00:05:44 vyos@Core:~$ show ipv6 route vrf LAN1 Codes: K - kernel route, C - connected, S - static, R - RIPng, O - OSPFv3, I - IS-IS, B - BGP, N - NHRP, T - Table, v - VNC, V - VNC-Direct, A - Babel, F - PBR, f - OpenFabric, > - selected route, * - FIB route, q - queued, r - rejected, b - backup t - trapped, o - offload failure VRF LAN1: C>* 2001:db8::/127 is directly connected, eth0, 00:18:43 S>* 2001:db8:0:1::/64 [1/0] via 2001:db8::1, eth0, weight 1, 00:16:03 C>* fe80::/64 is directly connected, eth0, 00:18:43 # ping vrf vyos@Core:~$ ping 10.1.1.2 vrf LAN1 PING 10.1.1.2 (10.1.1.2) 56(84) bytes of data. 64 bytes from 10.1.1.2: icmp_seq=1 ttl=64 time=1.52 ms 64 bytes from 10.1.1.2: icmp_seq=2 ttl=64 time=0.830 ms ^C --- 10.1.1.2 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1002ms rtt min/avg/max/mdev = 0.830/1.174/1.518/0.344 ms vyos@Core:~$ ping 10.0.0.1 vrf LAN1 PING 10.0.0.1 (10.0.0.1) 56(84) bytes of data. 64 bytes from 10.0.0.1: icmp_seq=1 ttl=64 time=0.785 ms 64 bytes from 10.0.0.1: icmp_seq=2 ttl=64 time=0.948 ms ^C --- 10.0.0.1 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1002ms rtt min/avg/max/mdev = 0.785/0.866/0.948/0.081 ms vyos@Core:~$ ping 2001:db8:0:1::1 vrf LAN1 PING 2001:db8:0:1::1(2001:db8:0:1::1) 56 data bytes 64 bytes from 2001:db8:0:1::1: icmp_seq=1 ttl=64 time=3.04 ms 64 bytes from 2001:db8:0:1::1: icmp_seq=2 ttl=64 time=1.04 ms 64 bytes from 2001:db8:0:1::1: icmp_seq=3 ttl=64 time=0.925 ms ^C --- 2001:db8:0:1::1 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2004ms rtt min/avg/max/mdev = 0.925/1.665/3.035/0.969 ms Step 2: BGP Configuration for VRF-Lite -------------------------------------- - Configuration Setting BGP global local-as as well inside the VRF. Redistribute static routes to inject configured networks into the BGP process but still inside the VRF. .. code-block:: none # set BGP global local-as set protocols bgp local-as # set BGP VRF local-as and redistribution set vrf name protocols bgp local-as set vrf name protocols bgp address-family redistribute static - Verification Check the BGP VRF table and verify if the static routes are injected showing the correct next-hop information. .. code-block:: none # show ip bgp vrf # show bgp vrf ipv6 vyos@Core:~$ show ip bgp vrf LAN1 BGP table version is 3, local router ID is 10.1.1.1, vrf id 8 Default local pref 100, local AS 64496 Status codes: s suppressed, d damped, h history, * valid, > best, = multipath, i internal, r RIB-failure, S Stale, R Removed Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self Origin codes: i - IGP, e - EGP, ? - incomplete RPKI validation codes: V valid, I invalid, N Not found Network Next Hop Metric LocPrf Weight Path *> 10.0.0.0/24 10.1.1.2 0 32768 ? vyos@Core# run show bgp vrf LAN1 ipv6 BGP table version is 13, local router ID is 10.1.1.1, vrf id 8 Default local pref 100, local AS 64496 Status codes: s suppressed, d damped, h history, * valid, > best, = multipath, i internal, r RIB-failure, S Stale, R Removed Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self Origin codes: i - IGP, e - EGP, ? - incomplete RPKI validation codes: V valid, I invalid, N Not found Network Next Hop Metric LocPrf Weight Path *> 2001:db8:0:1::/64 2001:db8::1 0 32768 ? Step 3: VPN Configuration ------------------------- - Configuration Within the VRF we set the Route-Distinguisher (RD) and Route-Targets (RT), then we enable the export/import VPN. .. code-block:: none # set Route-distinguisher set vrf name protocols bgp address-family rd vpn export '' # set route-target for import/export # Note: RT are a list that can be more than one community between apostrophe # and separated by blank space. Ex: ' ' set vrf name protocols bgp address-family route-target vpn export '' set vrf name protocols bgp address-family route-target vpn import '' # Enable VPN export/import under this VRF set vrf name protocols bgp address-family export vpn set vrf name protocols bgp address-family import vpn A key point to understand is that if we need two VRFs to communicate between each other EXPORT rt from VRF1 has to be in the IMPORT rt list from VRF2. But this is only in ONE direction, to complete the communication the EXPORT rt from VRF2 has to be in the IMPORT rt list from VRF1. There are some cases where this is not needed -for example, in some DDoS appliance- but most inter-vrf routing designs use the above configurations. - Verification After configured all the VRFs involved in this topology we take a deeper look at both BGP and Routing table for the VRF LAN1 .. code-block:: none # show ip bgp vrf # show bgp vrf ipv6 vyos@Core# run show ip bgp vrf LAN1 BGP table version is 53, local router ID is 10.1.1.1, vrf id 8 Default local pref 100, local AS 64496 Status codes: s suppressed, d damped, h history, * valid, > best, = multipath, i internal, r RIB-failure, S Stale, R Removed Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self Origin codes: i - IGP, e - EGP, ? - incomplete RPKI validation codes: V valid, I invalid, N Not found Network Next Hop Metric LocPrf Weight Path *> 0.0.0.0/0 10.2.2.2@7< 0 64497 i *> 10.0.0.0/24 10.1.1.2 0 32768 ? *> 10.2.2.0/30 10.2.2.2@7< 0 0 64497 ? *> 192.0.2.0/24 10.2.2.2@7< 0 0 64497 ? *> 192.168.0.0/24 192.168.3.2@11< 0 32768 ? *> 198.51.100.0/24 10.2.2.2@7< 0 0 64497 ? *> 203.0.113.0/24 10.2.2.2@7< 0 0 64497 ? vyos@Core# run show bgp vrf LAN1 ipv6 BGP table version is 13, local router ID is 10.1.1.1, vrf id 8 Default local pref 100, local AS 64496 Status codes: s suppressed, d damped, h history, * valid, > best, = multipath, i internal, r RIB-failure, S Stale, R Removed Nexthop codes: @NNN nexthop's vrf id, < announce-nh-self Origin codes: i - IGP, e - EGP, ? - incomplete RPKI validation codes: V valid, I invalid, N Not found Network Next Hop Metric LocPrf Weight Path *> ::/0 fe80::5200:ff:fe02:3@7< 0 64497 i *> 2001:db8::6/127 fe80::5200:ff:fe02:3@7< 0 0 64497 ? *> 2001:db8:0:1::/64 2001:db8::1 0 32768 ? *> 2001:db8:0:3::/64 2001:db8::5@11< 0 32768 ? *> 2001:db8:1::/48 fe80::5200:ff:fe02:3@7< 0 0 64497 ? *> 2001:db8:2::/48 fe80::5200:ff:fe02:3@7< 0 0 64497 ? *> 2001:db8:3::/48 fe80::5200:ff:fe02:3@7< 0 0 64497 ? # show ip route vrf # show ipv6 route vrf vyos@Core:~$ show ip route vrf LAN1 Codes: K - kernel route, C - connected, S - static, R - RIP, O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP, T - Table, v - VNC, V - VNC-Direct, A - Babel, F - PBR, f - OpenFabric, > - selected route, * - FIB route, q - queued, r - rejected, b - backup t - trapped, o - offload failure VRF LAN1: B>* 0.0.0.0/0 [20/0] via 10.2.2.2, eth3 (vrf Internet), weight 1, 00:00:38 S>* 10.0.0.0/24 [1/0] via 10.1.1.2, eth0, weight 1, 00:29:57 C>* 10.1.1.0/30 is directly connected, eth0, 00:29:59 B 10.2.2.0/30 [20/0] via 10.2.2.2 (vrf Internet) inactive, weight 1, 00:00:38 B>* 172.16.0.0/24 [20/0] via 172.16.2.2, eth1 (vrf LAN2), weight 1, 00:00:38 B>* 192.0.2.0/24 [20/0] via 10.2.2.2, eth3 (vrf Internet), weight 1, 00:00:38 B>* 198.51.100.0/24 [20/0] via 10.2.2.2, eth3 (vrf Internet), weight 1, 00:00:38 B>* 203.0.113.0/24 [20/0] via 10.2.2.2, eth3 (vrf Internet), weight 1, 00:00:38 vyos@Core# run show ipv6 route vrf LAN1 Codes: K - kernel route, C - connected, S - static, R - RIPng, O - OSPFv3, I - IS-IS, B - BGP, N - NHRP, T - Table, v - VNC, V - VNC-Direct, A - Babel, F - PBR, f - OpenFabric, > - selected route, * - FIB route, q - queued, r - rejected, b - backup t - trapped, o - offload failure VRF LAN1: B>* ::/0 [20/0] via fe80::5200:ff:fe02:3, eth3 (vrf Internet), weight 1, 00:07:50 C>* 2001:db8::/127 is directly connected, eth0, 05:33:43 B>* 2001:db8::6/127 [20/0] via fe80::5200:ff:fe02:3, eth3 (vrf Internet), weight 1, 00:07:50 S>* 2001:db8:0:1::/64 [1/0] via 2001:db8::1, eth0, weight 1, 05:31:03 B>* 2001:db8:0:3::/64 [20/0] via 2001:db8::5, eth2 (vrf Management), weight 1, 00:07:50 B>* 2001:db8:1::/48 [20/0] via fe80::5200:ff:fe02:3, eth3 (vrf Internet), weight 1, 00:07:50 B>* 2001:db8:2::/48 [20/0] via fe80::5200:ff:fe02:3, eth3 (vrf Internet), weight 1, 00:07:50 B>* 2001:db8:3::/48 [20/0] via fe80::5200:ff:fe02:3, eth3 (vrf Internet), weight 1, 00:07:50 C>* fe80::/64 is directly connected, eth0, 05:33:43 As we can see in the BGP table any imported route has been injected with a "@" followed by the VPN id; In the routing table of the VRF, if the route was installed, we can see -between round brackets- the exported VRF table. Step 4: End to End verification ------------------------------- Now we perform some end-to-end testing - From Management to LAN1/LAN2 .. code-block:: none vyos@Management:~$ ping 10.0.0.1 source-address 192.168.0.1 PING 10.0.0.1 (10.0.0.1) from 192.168.0.1 : 56(84) bytes of data. 64 bytes from 10.0.0.1: icmp_seq=1 ttl=63 time=1.93 ms 64 bytes from 10.0.0.1: icmp_seq=2 ttl=63 time=2.12 ms 64 bytes from 10.0.0.1: icmp_seq=3 ttl=63 time=2.12 ms ^C --- 10.0.0.1 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2005ms rtt min/avg/max/mdev = 1.931/2.056/2.123/0.088 ms vyos@Management:~$ ping 172.16.0.1 source-address 192.168.0.1 PING 172.16.0.1 (172.16.0.1) from 192.168.0.1 : 56(84) bytes of data. 64 bytes from 172.16.0.1: icmp_seq=1 ttl=63 time=1.62 ms 64 bytes from 172.16.0.1: icmp_seq=2 ttl=63 time=1.75 ms ^C --- 172.16.0.1 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1001ms rtt min/avg/max/mdev = 1.621/1.686/1.752/0.065 ms vyos@Management:~$ ping 2001:db8:0:1::1 source-address 2001:db8:0:3::1 PING 2001:db8:0:1::1(2001:db8:0:1::1) from 2001:db8:0:3::1 : 56 data bytes 64 bytes from 2001:db8:0:1::1: icmp_seq=1 ttl=63 time=2.44 ms 64 bytes from 2001:db8:0:1::1: icmp_seq=2 ttl=63 time=2.40 ms 64 bytes from 2001:db8:0:1::1: icmp_seq=3 ttl=63 time=2.41 ms ^C --- 2001:db8:0:1::1 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2003ms rtt min/avg/max/mdev = 2.399/2.418/2.442/0.017 ms vyos@Management:~$ ping 2001:db8:0:2::1 source-address 2001:db8:0:3::1 PING 2001:db8:0:2::1(2001:db8:0:2::1) from 2001:db8:0:3::1 : 56 data bytes 64 bytes from 2001:db8:0:2::1: icmp_seq=1 ttl=63 time=1.66 ms 64 bytes from 2001:db8:0:2::1: icmp_seq=2 ttl=63 time=1.99 ms 64 bytes from 2001:db8:0:2::1: icmp_seq=3 ttl=63 time=1.88 ms 64 bytes from 2001:db8:0:2::1: icmp_seq=4 ttl=63 time=2.32 ms ^C --- 2001:db8:0:2::1 ping statistics --- 4 packets transmitted, 4 received, 0% packet loss, time 3005ms rtt min/avg/max/mdev = 1.660/1.960/2.315/0.236 ms - From Management to Outside (fails as intended) .. code-block:: none vyos@Management:~$ show ip route Codes: K - kernel route, C - connected, S - static, R - RIP, O - OSPF, I - IS-IS, B - BGP, E - EIGRP, N - NHRP, T - Table, v - VNC, V - VNC-Direct, A - Babel, F - PBR, f - OpenFabric, > - selected route, * - FIB route, q - queued, r - rejected, b - backup t - trapped, o - offload failure S>* 0.0.0.0/0 [1/0] via 192.168.3.1, eth2, weight 1, 00:01:58 C>* 192.168.0.0/24 is directly connected, dum0, 00:02:05 C>* 192.168.3.0/30 is directly connected, eth2, 00:02:03 vyos@Management:~$ ping 192.0.2.1 PING 192.0.2.1 (192.0.2.1) 56(84) bytes of data. From 192.168.3.1 icmp_seq=1 Destination Net Unreachable From 192.168.3.1 icmp_seq=2 Destination Net Unreachable ^C --- 192.0.2.1 ping statistics --- 2 packets transmitted, 0 received, +2 errors, 100% packet loss, time 1002ms vyos@Management:~$ ping 195.51.100.1 PING 195.51.100.1 (195.51.100.1) 56(84) bytes of data. From 192.168.3.1 icmp_seq=1 Destination Net Unreachable From 192.168.3.1 icmp_seq=2 Destination Net Unreachable From 192.168.3.1 icmp_seq=3 Destination Net Unreachable ^C --- 195.51.100.1 ping statistics --- 3 packets transmitted, 0 received, +3 errors, 100% packet loss, time 2003ms vyos@Management:~$ ping 2001:db8:1::1 PING 2001:db8:1::1(2001:db8:1::1) 56 data bytes From 2001:db8::4 icmp_seq=1 Destination unreachable: No route From 2001:db8::4 icmp_seq=2 Destination unreachable: No route ^C --- 2001:db8:1::1 ping statistics --- 2 packets transmitted, 0 received, +2 errors, 100% packet loss, time 1002ms vyos@Management:~$ ping 2001:db8:2::1 PING 2001:db8:2::1(2001:db8:2::1) 56 data bytes From 2001:db8::4 icmp_seq=1 Destination unreachable: No route From 2001:db8::4 icmp_seq=2 Destination unreachable: No route ^C --- 2001:db8:2::1 ping statistics --- 2 packets transmitted, 0 received, +2 errors, 100% packet loss, time 1002ms - LAN1 to Outside .. code-block:: none vyos@LAN1:~$ ping 192.0.2.1 source-address 10.0.0.1 PING 192.0.2.1 (192.0.2.1) from 10.0.0.1 : 56(84) bytes of data. 64 bytes from 192.0.2.1: icmp_seq=1 ttl=63 time=1.47 ms 64 bytes from 192.0.2.1: icmp_seq=2 ttl=63 time=1.41 ms 64 bytes from 192.0.2.1: icmp_seq=3 ttl=63 time=1.80 ms ^C --- 192.0.2.1 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2004ms rtt min/avg/max/mdev = 1.414/1.563/1.803/0.171 ms vyos@LAN1:~$ ping 198.51.100.1 source-address 10.0.0.1 PING 198.51.100.1 (198.51.100.1) from 10.0.0.1 : 56(84) bytes of data. 64 bytes from 198.51.100.1: icmp_seq=1 ttl=63 time=1.71 ms 64 bytes from 198.51.100.1: icmp_seq=2 ttl=63 time=1.83 ms ^C --- 198.51.100.1 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1002ms rtt min/avg/max/mdev = 1.705/1.766/1.828/0.061 ms vyos@LAN1:~$ ping 203.0.113.1 source-address 10.0.0.1 PING 203.0.113.1 (203.0.113.1) from 10.0.0.1 : 56(84) bytes of data. 64 bytes from 203.0.113.1: icmp_seq=1 ttl=63 time=1.25 ms 64 bytes from 203.0.113.1: icmp_seq=2 ttl=63 time=1.88 ms ^C --- 203.0.113.1 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1003ms rtt min/avg/max/mdev = 1.249/1.566/1.884/0.317 ms vyos@LAN1:~$ ping 2001:db8:1::1 source-address 2001:db8:0:1::1 PING 2001:db8:1::1(2001:db8:1::1) from 2001:db8:0:1::1 : 56 data bytes 64 bytes from 2001:db8:1::1: icmp_seq=1 ttl=63 time=2.35 ms 64 bytes from 2001:db8:1::1: icmp_seq=2 ttl=63 time=2.29 ms 64 bytes from 2001:db8:1::1: icmp_seq=3 ttl=63 time=2.22 ms ^C --- 2001:db8:1::1 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2004ms rtt min/avg/max/mdev = 2.215/2.285/2.352/0.055 ms vyos@LAN1:~$ ping 2001:db8:2::1 source-address 2001:db8:0:1::1 PING 2001:db8:2::1(2001:db8:2::1) from 2001:db8:0:1::1 : 56 data bytes 64 bytes from 2001:db8:2::1: icmp_seq=1 ttl=63 time=1.37 ms 64 bytes from 2001:db8:2::1: icmp_seq=2 ttl=63 time=2.68 ms 64 bytes from 2001:db8:2::1: icmp_seq=3 ttl=63 time=2.00 ms ^C --- 2001:db8:2::1 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2003ms rtt min/avg/max/mdev = 1.367/2.015/2.679/0.535 ms .. note:: we are using "source-address" option cause we are not redistributing connected interfaces into BGP on the Core router hence there is no comeback route and ping will fail. - LAN1 to LAN2 .. code-block:: none vyos@LAN1:~$ ping 172.16.0.1 source-address 10.0.0.1 PING 172.16.0.1 (172.16.0.1) from 10.0.0.1 : 56(84) bytes of data. 64 bytes from 172.16.0.1: icmp_seq=1 ttl=63 time=3.00 ms 64 bytes from 172.16.0.1: icmp_seq=2 ttl=63 time=2.20 ms ^C --- 172.16.0.1 ping statistics --- 2 packets transmitted, 2 received, 0% packet loss, time 1002ms rtt min/avg/max/mdev = 2.199/2.600/3.001/0.401 ms vyos@LAN1:~$ ping 2001:db8:0:2::1 source 2001:db8:0:1::1 PING 2001:db8:0:2::1(2001:db8:0:2::1) from 2001:db8:0:1::1 : 56 data bytes 64 bytes from 2001:db8:0:2::1: icmp_seq=1 ttl=63 time=4.82 ms 64 bytes from 2001:db8:0:2::1: icmp_seq=2 ttl=63 time=1.95 ms 64 bytes from 2001:db8:0:2::1: icmp_seq=3 ttl=63 time=1.98 ms ^C --- 2001:db8:0:2::1 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2003ms rtt min/avg/max/mdev = 1.949/2.915/4.815/1.343 ms *********** Conclusions *********** Inter-VRF routing is a well-known solution to address complex routing scenarios that enable -in a dynamic way- to leak routes between VRFs. Is recommended to take special consideration while designing route-targets and its application as it can minimize future interventions while creating a new VRF will automatically take the desired effect in its propagation. ********** Appendix-A ********** Full configuration from all devices =================================== - Core .. code-block:: none set interfaces ethernet eth0 address '10.1.1.1/30' set interfaces ethernet eth0 address '2001:db8::/127' set interfaces ethernet eth0 vrf 'LAN1' set interfaces ethernet eth1 address '172.16.2.1/30' set interfaces ethernet eth1 address '2001:db8::2/127' set interfaces ethernet eth1 vrf 'LAN2' set interfaces ethernet eth2 address '192.168.3.1/30' set interfaces ethernet eth2 address '2001:db8::4/127' set interfaces ethernet eth2 vrf 'Management' set interfaces ethernet eth3 address '10.2.2.1/30' set interfaces ethernet eth3 address '2001:db8::6/127' set interfaces ethernet eth3 vrf 'Internet' set protocols bgp address-family ipv4-unicast set protocols bgp local-as '64496' set vrf name Internet protocols bgp address-family ipv4-unicast export vpn set vrf name Internet protocols bgp address-family ipv4-unicast import vpn set vrf name Internet protocols bgp address-family ipv4-unicast rd vpn export '64496:100' set vrf name Internet protocols bgp address-family ipv4-unicast route-target vpn export '64496:100' set vrf name Internet protocols bgp address-family ipv4-unicast route-target vpn import '64496:1 64496:2' set vrf name Internet protocols bgp address-family ipv6-unicast export vpn set vrf name Internet protocols bgp address-family ipv6-unicast import vpn set vrf name Internet protocols bgp address-family ipv6-unicast rd vpn export '64496:100' set vrf name Internet protocols bgp address-family ipv6-unicast route-target vpn export '64496:100' set vrf name Internet protocols bgp address-family ipv6-unicast route-target vpn import '64496:1 64496:2' set vrf name Internet protocols bgp local-as '64496' set vrf name Internet protocols bgp neighbor 10.2.2.2 address-family ipv4-unicast set vrf name Internet protocols bgp neighbor 10.2.2.2 remote-as '64497' set vrf name Internet protocols bgp neighbor 2001:db8::7 address-family ipv6-unicast set vrf name Internet protocols bgp neighbor 2001:db8::7 remote-as '64497' set vrf name Internet table '104' set vrf name LAN1 protocols bgp address-family ipv4-unicast export vpn set vrf name LAN1 protocols bgp address-family ipv4-unicast import vpn set vrf name LAN1 protocols bgp address-family ipv4-unicast rd vpn export '64496:1' set vrf name LAN1 protocols bgp address-family ipv4-unicast redistribute static set vrf name LAN1 protocols bgp address-family ipv4-unicast route-target vpn export '64496:1' set vrf name LAN1 protocols bgp address-family ipv4-unicast route-target vpn import '64496:100 64996:50 64496:2' set vrf name LAN1 protocols bgp address-family ipv6-unicast export vpn set vrf name LAN1 protocols bgp address-family ipv6-unicast import vpn set vrf name LAN1 protocols bgp address-family ipv6-unicast rd vpn export '64496:1' set vrf name LAN1 protocols bgp address-family ipv6-unicast redistribute static set vrf name LAN1 protocols bgp address-family ipv6-unicast route-target vpn export '64496:1' set vrf name LAN1 protocols bgp address-family ipv6-unicast route-target vpn import '64496:100 64496:50 64496:2' set vrf name LAN1 protocols bgp local-as '64496' set vrf name LAN1 protocols static route 10.0.0.0/24 next-hop 10.1.1.2 set vrf name LAN1 protocols static route6 2001:db8:0:1::/64 next-hop 2001:db8::1 set vrf name LAN1 table '101' set vrf name LAN2 protocols bgp address-family ipv4-unicast export vpn set vrf name LAN2 protocols bgp address-family ipv4-unicast import vpn set vrf name LAN2 protocols bgp address-family ipv4-unicast rd vpn export '64496:2' set vrf name LAN2 protocols bgp address-family ipv4-unicast redistribute static set vrf name LAN2 protocols bgp address-family ipv4-unicast route-target vpn export '64496:2' set vrf name LAN2 protocols bgp address-family ipv4-unicast route-target vpn import '64496:100 64496:50 64496:1' set vrf name LAN2 protocols bgp address-family ipv6-unicast export vpn set vrf name LAN2 protocols bgp address-family ipv6-unicast import vpn set vrf name LAN2 protocols bgp address-family ipv6-unicast rd vpn export '64496:2' set vrf name LAN2 protocols bgp address-family ipv6-unicast redistribute static set vrf name LAN2 protocols bgp address-family ipv6-unicast route-target vpn export '64496:2' set vrf name LAN2 protocols bgp address-family ipv6-unicast route-target vpn import '64496:100 64496:50 64496:1' set vrf name LAN2 protocols bgp local-as '64496' set vrf name LAN2 protocols static route 172.16.0.0/24 next-hop 172.16.2.2 set vrf name LAN2 protocols static route6 2001:db8:0:2::/64 next-hop 2001:db8::3 set vrf name LAN2 table '102' set vrf name Management protocols bgp address-family ipv4-unicast export vpn set vrf name Management protocols bgp address-family ipv4-unicast import vpn set vrf name Management protocols bgp address-family ipv4-unicast rd vpn export '64496:50' set vrf name Management protocols bgp address-family ipv4-unicast redistribute static set vrf name Management protocols bgp address-family ipv4-unicast route-target vpn export '64496:50' set vrf name Management protocols bgp address-family ipv4-unicast route-target vpn import '64496:1 64496:2' set vrf name Management protocols bgp address-family ipv6-unicast export vpn set vrf name Management protocols bgp address-family ipv6-unicast import vpn set vrf name Management protocols bgp address-family ipv6-unicast rd vpn export '64496:50' set vrf name Management protocols bgp address-family ipv6-unicast redistribute static set vrf name Management protocols bgp address-family ipv6-unicast route-target vpn export '64496:50' set vrf name Management protocols bgp address-family ipv6-unicast route-target vpn import '64496:1 64496:2' set vrf name Management protocols bgp local-as '64496' set vrf name Management protocols static route 192.168.0.0/24 next-hop 192.168.3.2 set vrf name Management protocols static route6 2001:db8:0:3::/64 next-hop 2001:db8::5 set vrf name Management table '103' - LAN1 .. code-block:: none set interfaces dummy dum0 address '10.0.0.1/24' set interfaces dummy dum0 address '2001:db8:0:1::1/64' set interfaces ethernet eth0 address '10.1.1.2/30' set interfaces ethernet eth0 address '2001:db8::1/127' set protocols static route 0.0.0.0/0 next-hop 10.1.1.1 set protocols static route6 ::/0 next-hop 2001:db8::* - LAN2 .. code-block:: none set interfaces dummy dum0 address '172.16.0.1/24' set interfaces dummy dum0 address '2001:db8:0:2::1/64' set interfaces ethernet eth0 hw-id '50:00:00:03:00:00' set interfaces ethernet eth1 address '172.16.2.2/30' set interfaces ethernet eth1 address '2001:db8::3/127' set protocols static route 0.0.0.0/0 next-hop 172.16.2.1 set protocols static route6 ::/0 next-hop 2001:db8::2 - Management .. code-block:: none set interfaces dummy dum0 address '192.168.0.1/24' set interfaces dummy dum0 address '2001:db8:0:3::1/64' set interfaces ethernet eth2 address '192.168.3.2/30' set interfaces ethernet eth2 address '2001:db8::5/127' set protocols static route 0.0.0.0/0 next-hop 192.168.3.1 set protocols static route6 ::/0 next-hop 2001:db8::4 - ISP .. code-block:: none set interfaces dummy dum0 address '192.0.2.1/24' set interfaces dummy dum0 address '2001:db8:1::1/48' set interfaces dummy dum1 address '198.51.100.1/24' set interfaces dummy dum1 address '2001:db8:2::1/48' set interfaces dummy dum2 address '203.0.113.1/24' set interfaces dummy dum2 address '2001:db8:3::1/48' set interfaces ethernet eth3 address '10.2.2.2/30' set interfaces ethernet eth3 address '2001:db8::7/127' set protocols bgp address-family ipv4-unicast redistribute connected set protocols bgp address-family ipv6-unicast redistribute connected set protocols bgp local-as '64497' set protocols bgp neighbor 10.2.2.1 address-family ipv4-unicast default-originate set protocols bgp neighbor 10.2.2.1 remote-as '64496' set protocols bgp neighbor 2001:db8::6 address-family ipv6-unicast default-originate set protocols bgp neighbor 2001:db8::6 remote-as '64496' set protocols static route 0.0.0.0/0 next-hop 10.2.2.1 set protocols static route6 ::/0 next-hop 2001:db8::6 ********** Appendix-B ********** Route-Filtering =============== When importing routes using MP-BGP it is possible to filter a subset of them before are injected in the BGP table. One of the most common case is to use a route-map with an prefix-list. - Configuration We create a prefix-list first and add all the routes we need to. .. code-block:: none # set both ipv4 and ipv6 policies set policy prefix-list LAN2-Internet rule 1 action 'permit' set policy prefix-list LAN2-Internet rule 1 le '24' set policy prefix-list LAN2-Internet rule 1 prefix '198.51.0.0/16' set policy prefix-list LAN2-Internet rule 2 action 'permit' set policy prefix-list LAN2-Internet rule 2 prefix '192.0.2.0/24' set policy prefix-list LAN2-Internet rule 3 action 'permit' set policy prefix-list LAN2-Internet rule 3 prefix '192.168.0.0/24' set policy prefix-list LAN2-Internet rule 4 action 'permit' set policy prefix-list LAN2-Internet rule 4 prefix '10.0.0.0/24' set policy prefix-list6 LAN2-Internet-v6 rule 1 action 'permit' set policy prefix-list6 LAN2-Internet-v6 rule 1 prefix '2001:db8:1::/48' set policy prefix-list6 LAN2-Internet-v6 rule 2 action 'permit' set policy prefix-list6 LAN2-Internet-v6 rule 2 prefix '2001:db8:2::/48' set policy prefix-list6 LAN2-Internet-v6 rule 3 action 'permit' set policy prefix-list6 LAN2-Internet-v6 rule 3 prefix '2001:db8:0:3::/64' set policy prefix-list6 LAN2-Internet-v6 rule 4 action 'permit' set policy prefix-list6 LAN2-Internet-v6 rule 4 prefix '2001:db8:0:1::/64' Then add a route-map and reference to above prefix. Consider that the actions taken inside the prefix will MATCH the routes that will be affected by the actions inside the rules of the route-map. .. code-block:: none set policy route-map LAN2-Internet rule 1 action 'permit' set policy route-map LAN2-Internet rule 1 match ip address prefix-list 'LAN2-Internet' set policy route-map LAN2-Internet-v6 rule 1 action 'permit' set policy route-map LAN2-Internet-v6 rule 1 match ipv6 address prefix-list 'LAN2-Internet-v6' We are using a "white list" approach by allowing only what is necessary. In case that need to implement a "black list" approach then you will need to change the action in the route-map for a deny BUT you need to add a rule that permits the rest due to the implicit deny in the route-map. Then we need to attach the policy to the BGP process. This needs to be under the import statement in the vrf we need to filter. .. code-block:: none set vrf name LAN2 protocols bgp address-family ipv4-unicast route-map vpn import 'LAN2-Internet' set vrf name LAN2 protocols bgp address-family ipv6-unicast route-map vpn import 'LAN2-Internet-v6' - Verification .. code-block:: none # show ip route vrf LAN2 B>* 10.0.0.0/24 [20/0] via 10.1.1.2, eth0 (vrf LAN1), weight 1, 00:45:28 S>* 172.16.0.0/24 [1/0] via 172.16.2.2, eth1, weight 1, 00:45:32 C>* 172.16.2.0/30 is directly connected, eth1, 00:45:39 B>* 192.0.2.0/24 [20/0] via 10.2.2.2, eth3 (vrf Internet), weight 1, 00:45:24 B>* 192.168.0.0/24 [20/0] via 192.168.3.2, eth2 (vrf Managment), weight 1, 00:45:27 B>* 198.51.100.0/24 [20/0] via 10.2.2.2, eth3 (vrf Internet), weight 1, 00:45:24 # show ipv6 route vrf LAN2 C>* 2001:db8::2/127 is directly connected, eth1, 00:46:26 B>* 2001:db8:0:1::/64 [20/0] via 2001:db8::1, eth0 (vrf LAN1), weight 1, 00:46:17 S>* 2001:db8:0:2::/64 [1/0] via 2001:db8::3, eth1, weight 1, 00:46:21 B>* 2001:db8:0:3::/64 [20/0] via 2001:db8::5, eth2 (vrf Managment), weight 1, 00:46:16 B>* 2001:db8:1::/48 [20/0] via fe80::5200:ff:fe02:3, eth3 (vrf Internet), weight 1, 00:46:13 B>* 2001:db8:2::/48 [20/0] via fe80::5200:ff:fe02:3, eth3 (vrf Internet), weight 1, 00:46:13 C>* fe80::/64 is directly connected, eth1, 00:46:27 As we can see even if both VRF LAN1 and LAN2 has the same import RTs we are able to select which routes are effectively imported and installed.