:lastproofread: 2021-06-29 .. _firewall: ######## Firewall ######## ******** Overview ******** VyOS makes use of Linux `netfilter `_ for packet filtering. The firewall supports the creation of groups for ports, addresses, and networks (implemented using netfilter ipset) and the option of interface or zone based firewall policy. .. note:: **Important note on usage of terms:** The firewall makes use of the terms `in`, `out`, and `local` for firewall policy. Users experienced with netfilter often confuse `in` to be a reference to the `INPUT` chain, and `out` the `OUTPUT` chain from netfilter. This is not the case. These instead indicate the use of the `FORWARD` chain and either the input or output interface. The `INPUT` chain, which is used for local traffic to the OS, is a reference to as `local` with respect to its input interface. *************** Global settings *************** Some firewall settings are global and have an affect on the whole system. .. cfgcmd:: set firewall all-ping [enable | disable] By default, when VyOS receives an ICMP echo request packet destined for itself, it will answer with an ICMP echo reply, unless you avoid it through its firewall. With the firewall you can set rules to accept, drop or reject ICMP in, out or local traffic. You can also use the general **firewall all-ping** command. This command affects only to LOCAL (packets destined for your VyOS system), not to IN or OUT traffic. .. note:: **firewall all-ping** affects only to LOCAL and it always behaves in the most restrictive way .. code-block:: none set firewall all-ping enable When the command above is set, VyOS will answer every ICMP echo request addressed to itself, but that will only happen if no other rule is applied dropping or rejecting local echo requests. In case of conflict, VyOS will not answer ICMP echo requests. .. code-block:: none set firewall all-ping disable When the command above is set, VyOS will answer no ICMP echo request addressed to itself at all, no matter where it comes from or whether more specific rules are being applied to accept them. .. cfgcmd:: set firewall broadcast-ping [enable | disable] This setting enable or disable the response of icmp broadcast messages. The following system parameter will be altered: * ``net.ipv4.icmp_echo_ignore_broadcasts`` .. cfgcmd:: set firewall ip-src-route [enable | disable] .. cfgcmd:: set firewall ipv6-src-route [enable | disable] This setting handle if VyOS accept packets with a source route option. The following system parameter will be altered: * ``net.ipv4.conf.all.accept_source_route`` * ``net.ipv6.conf.all.accept_source_route`` .. cfgcmd:: set firewall receive-redirects [enable | disable] .. cfgcmd:: set firewall ipv6-receive-redirects [enable | disable] enable or disable of ICMPv4 or ICMPv6 redirect messages accepted by VyOS. The following system parameter will be altered: * ``net.ipv4.conf.all.accept_redirects`` * ``net.ipv6.conf.all.accept_redirects`` .. cfgcmd:: set firewall send-redirects [enable | disable] enable or disable ICMPv4 redirect messages send by VyOS The following system parameter will be altered: * ``net.ipv4.conf.all.send_redirects`` .. cfgcmd:: set firewall log-martians [enable | disable] enable or disable the logging of martian IPv4 packets. The following system parameter will be altered: * ``net.ipv4.conf.all.log_martians`` .. cfgcmd:: set firewall source-validation [strict | loose | disable] Set the IPv4 source validation mode. The following system parameter will be altered: * ``net.ipv4.conf.all.rp_filter`` .. cfgcmd:: set firewall syn-cookies [enable | disable] Enable or Disable if VyOS use IPv4 TCP SYN Cookies. The following system parameter will be altered: * ``net.ipv4.tcp_syncookies`` .. cfgcmd:: set firewall twa-hazards-protection [enable | disable] Enable or Disable VyOS to be :rfc:`1337` conform. The following system parameter will be altered: * ``net.ipv4.tcp_rfc1337`` .. cfgcmd:: set firewall state-policy established action [accept | drop | reject] .. cfgcmd:: set firewall state-policy established log enable Set the global setting for an established connection. .. cfgcmd:: set firewall state-policy invalid action [accept | drop | reject] .. cfgcmd:: set firewall state-policy invalid log enable Set the global setting for invalid packets. .. cfgcmd:: set firewall state-policy related action [accept | drop | reject] .. cfgcmd:: set firewall state-policy related log enable Set the global setting for related connections. ****** Groups ****** Firewall groups represent collections of IP addresses, networks, ports, mac addresses or domains. Once created, a group can be referenced by firewall, nat and policy route rules as either a source or destination matcher. Members can be added or removed from a group without changes to, or the need to reload, individual firewall rules. Groups need to have unique names. Even though some contain IPv4 addresses and others contain IPv6 addresses, they still need to have unique names, so you may want to append "-v4" or "-v6" to your group names. Address Groups ============== In an **address group** a single IP address or IP address ranges are defined. .. cfgcmd:: set firewall group address-group address [address | address range] .. cfgcmd:: set firewall group ipv6-address-group address
Define a IPv4 or a IPv6 address group .. code-block:: none set firewall group address-group ADR-INSIDE-v4 address 192.168.0.1 set firewall group address-group ADR-INSIDE-v4 address 10.0.0.1-10.0.0.8 set firewall group ipv6-address-group ADR-INSIDE-v6 address 2001:db8::1 .. cfgcmd:: set firewall group address-group description .. cfgcmd:: set firewall group ipv6-address-group description Provide a IPv4 or IPv6 address group description Network Groups ============== While **network groups** accept IP networks in CIDR notation, specific IP addresses can be added as a 32-bit prefix. If you foresee the need to add a mix of addresses and networks, the network group is recommended. .. cfgcmd:: set firewall group network-group network .. cfgcmd:: set firewall group ipv6-network-group network Define a IPv4 or IPv6 Network group. .. code-block:: none set firewall group network-group NET-INSIDE-v4 network 192.168.0.0/24 set firewall group network-group NET-INSIDE-v4 network 192.168.1.0/24 set firewall group ipv6-network-group NET-INSIDE-v6 network 2001:db8::/64 .. cfgcmd:: set firewall group network-group description .. cfgcmd:: set firewall group ipv6-network-group description Provide a IPv4 or IPv6 network group description. Port Groups =========== A **port group** represents only port numbers, not the protocol. Port groups can be referenced for either TCP or UDP. It is recommended that TCP and UDP groups are created separately to avoid accidentally filtering unnecessary ports. Ranges of ports can be specified by using `-`. .. cfgcmd:: set firewall group port-group port [portname | portnumber | startport-endport] Define a port group. A port name can be any name defined in /etc/services. e.g.: http .. code-block:: none set firewall group port-group PORT-TCP-SERVER1 port http set firewall group port-group PORT-TCP-SERVER1 port 443 set firewall group port-group PORT-TCP-SERVER1 port 5000-5010 .. cfgcmd:: set firewall group port-group description Provide a port group description. MAC Groups ========== A **mac group** represents a collection of mac addresses. .. cfgcmd:: set firewall group mac-group mac-address Define a mac group. .. code-block:: none set firewall group mac-group MAC-G01 mac-address 88:a4:c2:15:b6:4f set firewall group mac-group MAC-G01 mac-address 4c:d5:77:c0:19:81 Domain Groups ============= A **domain group** represents a collection of domains. .. cfgcmd:: set firewall group domain-group address Define a domain group. .. code-block:: none set firewall group domain-group DOM address example.com ********* Rule-Sets ********* A rule-set is a named collection of firewall rules that can be applied to an interface or a zone. Each rule is numbered, has an action to apply if the rule is matched, and the ability to specify the criteria to match. Data packets go through the rules from 1 - 999999, at the first match the action of the rule will be executed. .. cfgcmd:: set firewall name description .. cfgcmd:: set firewall ipv6-name description Provide a rule-set description. .. cfgcmd:: set firewall name default-action [drop | reject | accept] .. cfgcmd:: set firewall ipv6-name default-action [drop | reject | accept] This set the default action of the rule-set if no rule matched a packet criteria. .. cfgcmd:: set firewall name enable-default-log .. cfgcmd:: set firewall ipv6-name enable-default-log Use this command to enable the logging of the default action. .. cfgcmd:: set firewall name rule <1-999999> action [drop | reject | accept] .. cfgcmd:: set firewall ipv6-name rule <1-999999> action [drop | reject | accept] This required setting defines the action of the current rule. .. cfgcmd:: set firewall name rule <1-999999> description .. cfgcmd:: set firewall ipv6-name rule <1-999999> description Provide a description for each rule. .. cfgcmd:: set firewall name rule <1-999999> log [disable | enable] .. cfgcmd:: set firewall ipv6-name rule <1-999999> log [disable | enable] Enable or disable logging for the matched packet. .. cfgcmd:: set firewall name rule <1-999999> log-level [emerg | alert | crit | err | warn | notice | info | debug] .. cfgcmd:: set firewall ipv6-name rule <1-999999> log-level [emerg | alert | crit | err | warn | notice | info | debug] Define log-level. Only applicable if rule log is enable. .. cfgcmd:: set firewall name rule <1-999999> disable .. cfgcmd:: set firewall ipv6-name rule <1-999999> disable If you want to disable a rule but let it in the configuration. Matching criteria ================= There are a lot of matching criteria against which the package can be tested. .. cfgcmd:: set firewall name rule <1-999999> connection-status nat [destination | source] .. cfgcmd:: set firewall ipv6-name rule <1-999999> connection-status nat [destination | source] Match criteria based on nat connection status. .. cfgcmd:: set firewall name rule <1-999999> source address [address | addressrange | CIDR] .. cfgcmd:: set firewall name rule <1-999999> destination address [address | addressrange | CIDR] .. cfgcmd:: set firewall ipv6-name rule <1-999999> source address [address | addressrange | CIDR] .. cfgcmd:: set firewall ipv6-name rule <1-999999> destination address [address | addressrange | CIDR] This is similar to the network groups part, but here you are able to negate the matching addresses. .. code-block:: none set firewall name WAN-IN-v4 rule 100 source address 192.0.2.10-192.0.2.11 # with a '!' the rule match everything except the specified subnet set firewall name WAN-IN-v4 rule 101 source address !203.0.113.0/24 set firewall ipv6-name WAN-IN-v6 rule 100 source address 2001:db8::202 .. cfgcmd:: set firewall name rule <1-999999> source address-mask [address] .. cfgcmd:: set firewall name rule <1-999999> destination address-mask [address] .. cfgcmd:: set firewall ipv6-name rule <1-999999> source address-mask [address] .. cfgcmd:: set firewall ipv6-name rule <1-999999> destination address-mask [address] An arbitrary netmask can be applied to mask addresses to only match against a specific portion. This is particularly useful with IPv6 and a zone-based firewall as rules will remain valid if the IPv6 prefix changes and the host portion of systems IPv6 address is static (for example, with SLAAC or `tokenised IPv6 addresses `_) This functions for both individual addresses and address groups. .. code-block:: none # Match any IPv6 address with the suffix ::0000:0000:0000:beef set firewall ipv6-name WAN-LAN-v6 rule 100 destination address ::beef set firewall ipv6-name WAN-LAN-v6 rule 100 destination address-mask ::ffff:ffff:ffff:ffff # Match any IPv4 address with `11` as the 2nd octet and `13` as the forth octet set firewall name WAN-LAN-v4 rule 100 destination address 0.11.0.13 set firewall name WAN-LAN-v4 rule 100 destination address-mask 0.255.0.255 # Address groups set firewall group ipv6-address-group WEBSERVERS address ::1000 set firewall group ipv6-address-group WEBSERVERS address ::2000 set firewall name WAN-LAN-v6 rule 200 source group address-group WEBSERVERS set firewall name WAN-LAN-v6 rule 200 source address-mask ::ffff:ffff:ffff:ffff .. cfgcmd:: set firewall name rule <1-999999> source geoip country-code .. cfgcmd:: set firewall name rule <1-999999> source geoip inverse-match .. cfgcmd:: set firewall ipv6-name rule <1-999999> source geoip country-code .. cfgcmd:: set firewall ipv6-name rule <1-999999> source geoip inverse-match .. cfgcmd:: set firewall name rule <1-999999> destination geoip country-code .. cfgcmd:: set firewall name rule <1-999999> destination geoip inverse-match .. cfgcmd:: set firewall ipv6-name rule <1-999999> destination geoip country-code .. cfgcmd:: set firewall ipv6-name rule <1-999999> destination geoip inverse-match Match IP addresses based on its geolocation. More info: `geoip matching `_. Use inverse-match to match anything except the given country-codes. Data is provided by DB-IP.com under CC-BY-4.0 license. Attribution required, permits redistribution so we can include a database in images(~3MB compressed). Includes cron script (manually callable by op-mode update geoip) to keep database and rules updated. .. cfgcmd:: set firewall name rule <1-999999> source mac-address .. cfgcmd:: set firewall ipv6-name rule <1-999999> source mac-address Only in the source criteria, you can specify a mac-address. .. code-block:: none set firewall name LAN-IN-v4 rule 100 source mac-address 00:53:00:11:22:33 set firewall name LAN-IN-v4 rule 101 source mac-address !00:53:00:aa:12:34 .. cfgcmd:: set firewall name rule <1-999999> source port [1-65535 | portname | start-end] .. cfgcmd:: set firewall name rule <1-999999> destination port [1-65535 | portname | start-end] .. cfgcmd:: set firewall ipv6-name rule <1-999999> source port [1-65535 | portname | start-end] .. cfgcmd:: set firewall ipv6-name rule <1-999999> destination port [1-65535 | portname | start-end] A port can be set with a port number or a name which is here defined: ``/etc/services``. .. code-block:: none set firewall name WAN-IN-v4 rule 10 source port '22' set firewall name WAN-IN-v4 rule 11 source port '!http' set firewall name WAN-IN-v4 rule 12 source port 'https' Multiple source ports can be specified as a comma-separated list. The whole list can also be "negated" using '!'. For example: .. code-block:: none set firewall ipv6-name WAN-IN-v6 rule 10 source port '!22,https,3333-3338' .. cfgcmd:: set firewall name rule <1-999999> source group address-group .. cfgcmd:: set firewall name rule <1-999999> destination group address-group .. cfgcmd:: set firewall ipv6-name rule <1-999999> source group address-group .. cfgcmd:: set firewall ipv6-name rule <1-999999> destination group address-group Use a specific address-group. Prepend character '!' for inverted matching criteria. .. cfgcmd:: set firewall name rule <1-999999> source group network-group .. cfgcmd:: set firewall name rule <1-999999> destination group network-group .. cfgcmd:: set firewall ipv6-name rule <1-999999> source group network-group .. cfgcmd:: set firewall ipv6-name rule <1-999999> destination group network-group Use a specific network-group. Prepend character '!' for inverted matching criteria. .. cfgcmd:: set firewall name rule <1-999999> source group port-group .. cfgcmd:: set firewall name rule <1-999999> destination group port-group .. cfgcmd:: set firewall ipv6-name rule <1-999999> source group port-group .. cfgcmd:: set firewall ipv6-name rule <1-999999> destination group port-group Use a specific port-group. Prepend character '!' for inverted matching criteria. .. cfgcmd:: set firewall name rule <1-999999> source group domain-group .. cfgcmd:: set firewall name rule <1-999999> destination group domain-group .. cfgcmd:: set firewall ipv6-name rule <1-999999> source group domain-group .. cfgcmd:: set firewall ipv6-name rule <1-999999> destination group domain-group Use a specific domain-group. Prepend character '!' for inverted matching criteria. .. cfgcmd:: set firewall name rule <1-999999> source group mac-group .. cfgcmd:: set firewall name rule <1-999999> destination group mac-group .. cfgcmd:: set firewall ipv6-name rule <1-999999> source group mac-group .. cfgcmd:: set firewall ipv6-name rule <1-999999> destination group mac-group Use a specific mac-group. Prepend character '!' for inverted matching criteria. .. cfgcmd:: set firewall name rule <1-999999> fragment [match-frag | match-non-frag] .. cfgcmd:: set firewall ipv6-name rule <1-999999> fragment [match-frag | match-non-frag] Match based on fragment criteria. .. cfgcmd:: set firewall name rule <1-999999> icmp [code | type] <0-255> .. cfgcmd:: set firewall ipv6-name rule <1-999999> icmpv6 [code | type] <0-255> Match based on icmp|icmpv6 code and type. .. cfgcmd:: set firewall name rule <1-999999> icmp type-name .. cfgcmd:: set firewall ipv6-name rule <1-999999> icmpv6 type-name Match based on icmp|icmpv6 type-name criteria. Use tab for information about what **type-name** criteria are supported. .. cfgcmd:: set firewall name rule <1-999999> ipsec [match-ipsec | match-none] .. cfgcmd:: set firewall ipv6-name rule <1-999999> ipsec [match-ipsec | match-none] Match based on ipsec criteria. .. cfgcmd:: set firewall name rule <1-999999> limit burst <0-4294967295> .. cfgcmd:: set firewall ipv6-name rule <1-999999> limit burst <0-4294967295> Match based on the maximum number of packets to allow in excess of rate. .. cfgcmd:: set firewall name rule <1-999999> limit rate .. cfgcmd:: set firewall ipv6-name rule <1-999999> limit rate Match based on the maximum average rate, specified as **integer/unit**. For example **5/minutes** .. cfgcmd:: set firewall name rule <1-999999> packet-length .. cfgcmd:: set firewall ipv6-name rule <1-999999> packet-length .. cfgcmd:: set firewall name rule <1-999999> packet-length-exclude .. cfgcmd:: set firewall ipv6-name rule <1-999999> packet-length-exclude Match based on packet length criteria. Multiple values from 1 to 65535 and ranges are supported. .. cfgcmd:: set firewall name rule <1-999999> protocol [ | <0-255> | all | tcp_udp] .. cfgcmd:: set firewall ipv6-name rule <1-999999> protocol [ | <0-255> | all | tcp_udp] Match a protocol criteria. A protocol number or a name which is here defined: ``/etc/protocols``. Special names are ``all`` for all protocols and ``tcp_udp`` for tcp and udp based packets. The ``!`` negate the selected protocol. .. code-block:: none set firewall name WAN-IN-v4 rule 10 protocol tcp_udp set firewall name WAN-IN-v4 rule 11 protocol !tcp_udp set firewall ipv6-name WAN-IN-v6 rule 10 protocol tcp .. cfgcmd:: set firewall name rule <1-999999> recent count <1-255> .. cfgcmd:: set firewall ipv6-name rule <1-999999> recent count <1-255> .. cfgcmd:: set firewall name rule <1-999999> recent time [second | minute | hour] .. cfgcmd:: set firewall ipv6-name rule <1-999999> recent time [second | minute | hour] Match bases on recently seen sources. .. cfgcmd:: set firewall name rule <1-999999> tcp flags .. cfgcmd:: set firewall ipv6-name rule <1-999999> tcp flags Allowed values fpr TCP flags: ``SYN``, ``ACK``, ``FIN``, ``RST``, ``URG``, ``PSH``, ``ALL`` When specifying more than one flag, flags should be comma separated. The ``!`` negate the selected protocol. .. code-block:: none set firewall name WAN-IN-v4 rule 10 tcp flags 'ACK' set firewall name WAN-IN-v4 rule 12 tcp flags 'SYN' set firewall name WAN-IN-v4 rule 13 tcp flags 'SYN,!ACK,!FIN,!RST' .. cfgcmd:: set firewall name rule <1-999999> state [established | invalid | new | related] [enable | disable] .. cfgcmd:: set firewall ipv6-name rule <1-999999> state [established | invalid | new | related] [enable | disable] Match against the state of a packet. .. cfgcmd:: set firewall name rule <1-999999> time startdate .. cfgcmd:: set firewall ipv6-name rule <1-999999> time startdate .. cfgcmd:: set firewall name rule <1-999999> time starttime .. cfgcmd:: set firewall ipv6-name rule <1-999999> time starttime .. cfgcmd:: set firewall name rule <1-999999> time stopdate .. cfgcmd:: set firewall ipv6-name rule <1-999999> time stopdate .. cfgcmd:: set firewall name rule <1-999999> time stoptime .. cfgcmd:: set firewall ipv6-name rule <1-999999> time stoptime .. cfgcmd:: set firewall name rule <1-999999> time weekdays .. cfgcmd:: set firewall ipv6-name rule <1-999999> time weekdays Time to match the defined rule. .. cfgcmd:: set firewall name rule <1-999999> ttl <0-255> Match time to live parameter, where 'eq' stands for 'equal'; 'gt' stands for 'greater than', and 'lt' stands for 'less than'. .. cfgcmd:: set firewall ipv6-name rule <1-999999> hop-limit <0-255> Match hop-limit parameter, where 'eq' stands for 'equal'; 'gt' stands for 'greater than', and 'lt' stands for 'less than'. .. cfgcmd:: set firewall name rule <1-999999> recent count <1-255> .. cfgcmd:: set firewall ipv6-name rule <1-999999> recent count <1-255> .. cfgcmd:: set firewall name rule <1-999999> recent time .. cfgcmd:: set firewall ipv6-name rule <1-999999> recent time Match when 'count' amount of connections are seen within 'time'. These matching criteria can be used to block brute-force attempts. *********************************** Applying a Rule-Set to an Interface *********************************** A Rule-Set can be applied to every interface: * ``in``: Ruleset for forwarded packets on an inbound interface * ``out``: Ruleset for forwarded packets on an outbound interface * ``local``: Ruleset for packets destined for this router .. cfgcmd:: set firewall interface [in | out | local] [name | ipv6-name] Here are some examples for applying a rule-set to an interface .. code-block:: none set firewall interface eth1.100 in name LANv4-IN set firewall interface eth1.100 out name LANv4-OUT set firewall interface bond0 in name LANv4-IN set firewall interface vtun1 in name LANv4-IN set firewall interface eth2* in name LANv4-IN .. note:: As you can see in the example here, you can assign the same rule-set to several interfaces. An interface can only have one rule-set per chain. .. note:: You can use wildcard ``*`` to match a group of interfaces. *********************** Operation-mode Firewall *********************** Rule-set overview ================= .. opcmd:: show firewall This will show you a basic firewall overview .. code-block:: none vyos@vyos:~$ show firewall ------------------------ Firewall Global Settings ------------------------ Firewall state-policy for all IPv4 and Ipv6 traffic state action log ----- ------ --- invalid accept disabled established accept disabled related accept disabled ----------------------------- Rulesets Information ----------------------------- -------------------------------------------------------------------------- IPv4 Firewall "DMZv4-1-IN": Active on (eth0,IN) rule action proto packets bytes ---- ------ ----- ------- ----- 10 accept icmp 0 0 condition - saddr 10.1.0.0/24 daddr 0.0.0.0/0 LOG enabled 10000 drop all 0 0 condition - saddr 0.0.0.0/0 daddr 0.0.0.0/0 LOG enabled -------------------------------------------------------------------------- IPv4 Firewall "DMZv4-1-OUT": Active on (eth0,OUT) rule action proto packets bytes ---- ------ ----- ------- ----- 10 accept tcp_udp 1 60 condition - saddr 0.0.0.0/0 daddr 0.0.0.0/0 match-DST-PORT-GROUP DMZ-Ports /* DMZv4-1-OUT-10 */LOG enabled 11 accept icmp 1 84 condition - saddr 0.0.0.0/0 daddr 0.0.0.0/0 /* DMZv4-1-OUT-11 */LOG enabled 10000 drop all 6 360 condition - saddr 0.0.0.0/0 daddr 0.0.0.0/0 LOG enabled -------------------------------------------------------------------------- IPv4 Firewall "LANv4-IN": Inactive - Not applied to any interfaces or zones. rule action proto packets bytes ---- ------ ----- ------- ----- 10 accept all 0 0 condition - saddr 0.0.0.0/0 daddr 0.0.0.0/0 /* LANv4-IN-10 */ 10000 drop all 0 0 condition - saddr 0.0.0.0/0 daddr 0.0.0.0/0 .. opcmd:: show firewall summary This will show you a summary of rule-sets and groups .. code-block:: none vyos@vyos:~$ show firewall summary ------------------------ Firewall Global Settings ------------------------ Firewall state-policy for all IPv4 and Ipv6 traffic state action log ----- ------ --- invalid accept disabled related accept disabled established accept disabled ------------------------ Firewall Rulesets ------------------------ IPv4 name: Rule-set name Description References ------------- ----------- ---------- DMZv4-1-OUT (eth0,OUT) DMZv4-1-IN (eth0,IN) ------------------------ Firewall Groups ------------------------ Port Groups: Group name Description References ---------- ----------- ---------- DMZ-Ports DMZv4-1-OUT-10-destination Network Groups: Group name Description References ---------- ----------- ---------- LANv4 LANv4-IN-10-source, DMZv4-1-OUT-10-source, DMZv4-1-OUT-11-source .. opcmd:: show firewall statistics This will show you a statistic of all rule-sets since the last boot. .. opcmd:: show firewall [name | ipv6name] rule <1-999999> This command will give an overview of a rule in a single rule-set .. opcmd:: show firewall group Overview of defined groups. You see the type, the members, and where the group is used. .. code-block:: none vyos@vyos:~$ show firewall group DMZ-Ports Name : DMZ-Ports Type : port References : none Members : 80 443 8080 8443 vyos@vyos:~$ show firewall group LANv4 Name : LANv4 Type : network References : LANv4-IN-10-source Members : 10.10.0.0/16 .. opcmd:: show firewall [name | ipv6name] This command will give an overview of a single rule-set. .. opcmd:: show firewall [name | ipv6name] statistics This will show you a rule-set statistic since the last boot. .. opcmd:: show firewall [name | ipv6name] rule <1-999999> This command will give an overview of a rule in a single rule-set. Zone-Policy Overview ==================== .. opcmd:: show zone-policy zone Use this command to get an overview of a zone. .. code-block:: none vyos@vyos:~$ show zone-policy zone DMZ ------------------- Name: DMZ Interfaces: eth0 eth1 From Zone: name firewall ---- -------- LAN DMZv4-1-OUT Show Firewall log ================= .. opcmd:: show log firewall [name | ipv6name] Show the logs of a specific Rule-Set. .. note:: At the moment it not possible to look at the whole firewall log with VyOS operational commands. All logs will save to ``/var/logs/messages``. For example: ``grep '10.10.0.10' /var/log/messages`` Example Partial Config ====================== .. code-block:: none firewall { interface eth0 { in { name FROM-INTERNET } } all-ping enable broadcast-ping disable config-trap disable group { network-group BAD-NETWORKS { network 198.51.100.0/24 network 203.0.113.0/24 } network-group GOOD-NETWORKS { network 192.0.2.0/24 } port-group BAD-PORTS { port 65535 } } name FROM-INTERNET { default-action accept description "From the Internet" rule 10 { action accept description "Authorized Networks" protocol all source { group { network-group GOOD-NETWORKS } } } rule 11 { action drop description "Bad Networks" protocol all source { group { network-group BAD-NETWORKS } } } rule 30 { action drop description "BAD PORTS" destination { group { port-group BAD-PORTS } } log enable protocol all } } } interfaces { ethernet eth1 { address dhcp description OUTSIDE duplex auto } } Update geoip database ===================== .. opcmd:: update geoip Command used to update GeoIP database and firewall sets.