:lastproofread: 2021-07-27 .. _wireguard: ######### WireGuard ######### WireGuard is an extremely simple yet fast and modern VPN that utilizes state-of-the-art cryptography. See https://www.wireguard.com for more information. **************** Site to Site VPN **************** This diagram corresponds with the example site to site configuration below. .. figure:: /_static/images/wireguard_site2site_diagram.jpg ************* Configuration ************* ******** Keypairs ******** WireGuard requires the generation of a keypair, which includes a private key to decrypt incoming traffic, and a public key for peer(s) to encrypt traffic. Generate Keypair ================ .. opcmd:: generate wireguard default-keypair It generates the keypair, which includes the public and private parts, and stores it within VyOS. It will be used per default on any configured WireGuard interface, even if multiple interfaces are being configured. .. opcmd:: show wireguard keypairs pubkey default It shows the public key to be shared with your peer(s). Your peer will encrypt all traffic to your system using this public key. .. code-block:: none vyos@vyos:~$ show wireguard keypairs pubkey default hW17UxY7zeydJNPIyo3UtGnBHkzTK/NeBOrDSIU9Tx0= Generate Named Keypair ====================== Named keypairs can be used on a interface basis when configured. If multiple WireGuard interfaces are being configured, each can have their own keypairs. .. opcmd:: generate wireguard named-keypairs The commands below generates 2 keypairs unrelated to each other. .. code-block:: none vyos@vyos:~$ generate wireguard named-keypairs KP01 vyos@vyos:~$ generate wireguard named-keypairs KP02 *********************** Interface configuration *********************** The next step is to configure your local side as well as the policy based trusted destination addresses. If you only initiate a connection, the listen port and address/port is optional; however, if you act like a server and endpoints initiate the connections to your system, you need to define a port your clients can connect to, otherwise the port is randomly chosen and may make connection difficult with firewall rules, since the port may be different each time the system is rebooted. You will also need the public key of your peer as well as the network(s) you want to tunnel (allowed-ips) to configure a WireGuard tunnel. The public key below is always the public key from your peer, not your local one. **local side - commands** .. code-block:: none set interfaces wireguard wg01 address '10.1.0.1/30' set interfaces wireguard wg01 description 'VPN-to-wg02' set interfaces wireguard wg01 peer to-wg02 allowed-ips '192.168.2.0/24' set interfaces wireguard wg01 peer to-wg02 address '' set interfaces wireguard wg01 peer to-wg02 port '51820' set interfaces wireguard wg01 peer to-wg02 pubkey 'XMrlPykaxhdAAiSjhtPlvi30NVkvLQliQuKP7AI7CyI=' set interfaces wireguard wg01 port '51820' set protocols static route 192.168.2.0/24 interface wg01 **local side - annotated commands** .. code-block:: none set interfaces wireguard wg01 address '10.1.0.1/30' # Address of the wg01 tunnel interface. set interfaces wireguard wg01 description 'VPN-to-wg02' set interfaces wireguard wg01 peer to-wg02 allowed-ips '192.168.2.0/24' # Subnets that are allowed to travel over the tunnel set interfaces wireguard wg01 peer to-wg02 address '' # Public IP of the peer set interfaces wireguard wg01 peer to-wg02 port '58120' # Port of the Peer set interfaces wireguard wg01 peer to-wg02 pubkey '' # Public Key of the Peer set interfaces wireguard wg01 port '51820' # Port of own server set protocols static route 192.168.2.0/24 interface wg01 # Static route to remote subnet The last step is to define an interface route for 10.2.0.0/24 to get through the WireGuard interface `wg01`. Multiple IPs or networks can be defined and routed. The last check is allowed-ips which either prevents or allows the traffic. .. note:: You can not assign the same allowed-ips statement to multiple WireGuard peers. This a design decision. For more information please check the `WireGuard mailing list`_. .. cfgcmd:: set interfaces wireguard private-key To use a named key on an interface, the option private-key needs to be set. .. code-block:: none set interfaces wireguard wg01 private-key KP01 The command :opcmd:`show wireguard keypairs pubkey KP01` will then show the public key, which needs to be shared with the peer. **remote side - commands** .. code-block:: none set interfaces wireguard wg01 address '10.1.0.2/30' set interfaces wireguard wg01 description 'VPN-to-wg01' set interfaces wireguard wg01 peer to-wg02 allowed-ips '192.168.1.0/24' set interfaces wireguard wg01 peer to-wg02 address '' set interfaces wireguard wg01 peer to-wg02 port '51820' set interfaces wireguard wg01 peer to-wg02 pubkey 'u41jO3OF73Gq1WARMMFG7tOfk7+r8o8AzPxJ1FZRhzk=' set interfaces wireguard wg01 port '51820' set protocols static route 192.168.1.0/24 interface wg01 **remote side - annotated commands** .. code-block:: none set interfaces wireguard wg01 address '10.1.0.2/30' # Address of the wg01 tunnel interface. set interfaces wireguard wg01 description 'VPN-to-wg01' set interfaces wireguard wg01 peer to-wg02 allowed-ips '192.168.1.0/24' # Subnets that are allowed to travel over the tunnel set interfaces wireguard wg01 peer to-wg02 address 'Site1 Pub IP' # Public IP address of the Peer set interfaces wireguard wg01 peer to-wg02 port '51820' # Port of the Peer set interfaces wireguard wg01 peer to-wg02 pubkey '' # Public key of the Peer set interfaces wireguard wg01 port '51820' # Port of own server set protocols static route 192.168.1.0/24 interface wg01 # Static route to remote subnet ******************* Firewall Exceptions ******************* For the WireGuard traffic to pass through the WAN interface, you must create a firewall exception. .. code-block:: none set firewall name OUTSIDE_LOCAL rule 10 action accept set firewall name OUTSIDE_LOCAL rule 10 description 'Allow established/related' set firewall name OUTSIDE_LOCAL rule 10 state established enable set firewall name OUTSIDE_LOCAL rule 10 state related enable set firewall name OUTSIDE_LOCAL rule 20 action accept set firewall name OUTSIDE_LOCAL rule 20 description WireGuard_IN set firewall name OUTSIDE_LOCAL rule 20 destination port 51820 set firewall name OUTSIDE_LOCAL rule 20 log enable set firewall name OUTSIDE_LOCAL rule 20 protocol udp set firewall name OUTSIDE_LOCAL rule 20 source You should also ensure that the OUTISDE_LOCAL firewall group is applied to the WAN interface and a direction (local). .. code-block:: none set interfaces ethernet eth0 firewall local name 'OUTSIDE-LOCAL' Assure that your firewall rules allow the traffic, in which case you have a working VPN using WireGuard. .. code-block:: none wg01# ping 192.168.1.1 PING 192.168.1.1 (192.168.1.1) 56(84) bytes of data. 64 bytes from 192.168.1.1: icmp_seq=1 ttl=64 time=1.16 ms 64 bytes from 192.168.1.1: icmp_seq=2 ttl=64 time=1.77 ms wg02# ping 192.168.2.1 PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data. 64 bytes from 192.168.2.1: icmp_seq=1 ttl=64 time=4.40 ms 64 bytes from 192.168.2.1: icmp_seq=2 ttl=64 time=1.02 ms An additional layer of symmetric-key crypto can be used on top of the asymmetric crypto. This is optional. .. code-block:: none wg01# run generate wireguard preshared-key rvVDOoc2IYEnV+k5p7TNAmHBMEGTHbPU8Qqg8c/sUqc= Copy the key, as it is not stored on the local filesystem. Because it is a symmetric key, only you and your peer should have knowledge of its content. Make sure you distribute the key in a safe manner, .. code-block:: none wg01# set interfaces wireguard wg01 peer to-wg02 preshared-key 'rvVDOoc2IYEnV+k5p7TNAmHBMEGTHbPU8Qqg8c/sUqc=' wg02# set interfaces wireguard wg01 peer to-wg01 preshared-key 'rvVDOoc2IYEnV+k5p7TNAmHBMEGTHbPU8Qqg8c/sUqc=' *********************************** Remote Access "RoadWarrior" Example *********************************** With WireGuard, a Road Warrior VPN config is similar to a site-to-site VPN. It just lacks the ``address`` and ``port`` statements. In the following example, the IPs for the remote clients are defined in the peers. This allows the peers to interact with one another. .. code-block:: none wireguard wg0 { address 10.172.24.1/24 address 2001:DB8:470:22::1/64 description RoadWarrior peer MacBook { allowed-ips 10.172.24.30/32 allowed-ips 2001:DB8:470:22::30/128 persistent-keepalive 15 pubkey F5MbW7ye7DsoxdOaixjdrudshjjxN5UdNV+pGFHqehc= } peer iPhone { allowed-ips 10.172.24.20/32 allowed-ips 2001:DB8:470:22::20/128 persistent-keepalive 15 pubkey BknHcLFo8nOo8Dwq2CjaC/TedchKQ0ebxC7GYn7Al00= } port 2224 } The following is the config for the iPhone peer above. It's important to note that the ``AllowedIPs`` wildcard setting directs all IPv4 and IPv6 traffic through the connection. .. code-block:: none [Interface] PrivateKey = ARAKLSDJsadlkfjasdfiowqeruriowqeuasdf= Address = 10.172.24.20/24, 2001:DB8:470:22::20/64 DNS = 10.0.0.53, 10.0.0.54 [Peer] PublicKey = RIbtUTCfgzNjnLNPQ/ulkGnnB2vMWHm7l2H/xUfbyjc= AllowedIPs = 0.0.0.0/0, ::/0 Endpoint = 192.0.2.1:2224 PersistentKeepalive = 25 However, split-tunneling can be achieved by specifying the remote subnets. This ensures that only traffic destined for the remote site is sent over the tunnel. All other traffic is unaffected. .. code-block:: none [Interface] PrivateKey = 8Iasdfweirousd1EVGUk5XsT+wYFZ9mhPnQhmjzaJE6Go= Address = 10.172.24.30/24, 2001:DB8:470:22::30/64 [Peer] PublicKey = RIbtUTCfgzNjnLNPQ/ulkGnnB2vMWHm7l2H/xUfbyjc= AllowedIPs = 10.172.24.30/24, 2001:DB8:470:22::/64 Endpoint = 192.0.2.1:2224 PersistentKeepalive = 25 ******************** Operational Commands ******************** Status ====== .. opcmd:: show interfaces wireguard wg0 summary Show info about the Wireguard service. It also shows the latest handshake. .. code-block:: none vyos@vyos:~$ show interfaces wireguard wg0 summary interface: wg0 public key: private key: (hidden) listening port: 51820 peer: endpoint: allowed ips: 10.69.69.2/32 latest handshake: 23 hours, 45 minutes, 26 seconds ago transfer: 1.26 MiB received, 6.47 MiB sent .. opcmd:: show interfaces wireguard Get a list of all wireguard interfaces .. code-block:: none Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down Interface IP Address S/L Description --------- ---------- --- ----------- wg0 10.0.0.1/24 u/u .. opcmd:: show interfaces wireguard Show general information about specific WireGuard interface .. code-block:: none vyos@vyos:~$ show interfaces wireguard wg01 interface: wg0 address: 10.0.0.1/24 public key: h1HkYlSuHdJN6Qv4Hz4bBzjGg5WUty+U1L7DJsZy1iE= private key: (hidden) listening port: 41751 RX: bytes packets errors dropped overrun mcast 0 0 0 0 0 0 TX: bytes packets errors dropped carrier collisions 0 0 0 0 0 0 *************** Encryption Keys *************** .. opcmd:: show wireguard keypair pubkey Show public key portion for specified key. This can be either the ``default`` key, or any other named key-pair. The ``default`` keypair .. code-block:: none vyos@vyos:~$ show wireguard keypair pubkey default FAXCPb6EbTlSH5200J5zTopt9AYXneBthAySPBLbZwM= Name keypair ``KP01`` .. code-block:: none vyos@vyos:~$ show wireguard keypair pubkey KP01 HUtsu198toEnm1poGoRTyqkUKfKUdyh54f45dtcahDM= .. opcmd:: delete wireguard keypair pubkey Delete a keypair, this can be either the ``default`` key, or any other named key-pair. .. code-block:: none vyos@vyos:~$ delete wireguard keypair default *********************************** Remote Access "RoadWarrior" clients *********************************** Some users tend to connect their mobile devices using WireGuard to their VyOS router. To ease deployment one can generate a "per mobile" configuration from the VyOS CLI. .. warning:: From a security perspective, it is not recommended to let a third party create and share the private key for a secured connection. You should create the private portion on your own and only hand out the public key. Please keep this in mind when using this convenience feature. .. opcmd:: generate wireguard client-config interface server address Using this command, you will create a new client configuration which can connect to ``interface`` on this router. The public key from the specified interface is automatically extracted and embedded into the configuration. The command also generates a configuration snipped which can be copy/pasted into the VyOS CLI if needed. The supplied ```` on the CLI will become the peer name in the snippet. In addition you will specifiy the IP address or FQDN for the client where it will connect to. The address parameter can be used up to two times and is used to assign the clients specific IPv4 (/32) or IPv6 (/128) address. .. figure:: /_static/images/wireguard_qrcode.jpg :alt: WireGuard Client QR code .. stop_vyoslinter .. _`WireGuard mailing list`: https://lists.zx2c4.com/pipermail/wireguard/2018-December/003704.html .. start_vyoslinter