.. _nat44: ##### NAT44 ##### :abbr:`NAT (Network Address Translation)` is a common method of remapping one IP address space into another by modifying network address information in the IP header of packets while they are in transit across a traffic routing device. The technique was originally used as a shortcut to avoid the need to readdress every host when a network was moved. It has become a popular and essential tool in conserving global address space in the face of IPv4 address exhaustion. One Internet-routable IP address of a NAT gateway can be used for an entire private network. IP masquerading is a technique that hides an entire IP address space, usually consisting of private IP addresses, behind a single IP address in another, usually public address space. The hidden addresses are changed into a single (public) IP address as the source address of the outgoing IP packets so they appear as originating not from the hidden host but from the routing device itself. Because of the popularity of this technique to conserve IPv4 address space, the term NAT has become virtually synonymous with IP masquerading. As network address translation modifies the IP address information in packets, NAT implementations may vary in their specific behavior in various addressing cases and their effect on network traffic. The specifics of NAT behavior are not commonly documented by vendors of equipment containing NAT implementations. The computers on an internal network can use any of the addresses set aside by the :abbr:`IANA (Internet Assigned Numbers Authority)` for private addressing (see :rfc:`1918`). These reserved IP addresses are not in use on the Internet, so an external machine will not directly route to them. The following addresses are reserved for private use: * 10.0.0.0 to 10.255.255.255 (CIDR: 10.0.0.0/8) * 172.16.0.0 to 172.31.255.255 (CIDR: 172.16.0.0/12) * 192.168.0.0 to 192.168.255.255 (CIDR: 192.168.0.0/16) If an ISP deploys a :abbr:`CGN (Carrier-grade NAT)`, and uses :rfc:`1918` address space to number customer gateways, the risk of address collision, and therefore routing failures, arises when the customer network already uses an :rfc:`1918` address space. This prompted some ISPs to develop a policy within the :abbr:`ARIN (American Registry for Internet Numbers)` to allocate new private address space for CGNs, but ARIN deferred to the IETF before implementing the policy indicating that the matter was not a typical allocation issue but a reservation of addresses for technical purposes (per :rfc:`2860`). IETF published :rfc:`6598`, detailing a shared address space for use in ISP CGN deployments that can handle the same network prefixes occurring both on inbound and outbound interfaces. ARIN returned address space to the :abbr:`IANA (Internet Assigned Numbers Authority)` for this allocation. The allocated address block is 100.64.0.0/10. Devices evaluating whether an IPv4 address is public must be updated to recognize the new address space. Allocating more private IPv4 address space for NAT devices might prolong the transition to IPv6. Overview ======== Different NAT Types ------------------- .. _source-nat: SNAT ^^^^ :abbr:`SNAT (Source Network Address Translation)` is the most common form of :abbr:`NAT (Network Address Translation)` and is typically referred to simply as NAT. To be more correct, what most people refer to as :abbr:`NAT (Network Address Translation)` is actually the process of :abbr:`PAT (Port Address Translation)`, or NAT overload. SNAT is typically used by internal users/private hosts to access the Internet - the source address is translated and thus kept private. .. _destination-nat: DNAT ^^^^ :abbr:`DNAT (Destination Network Address Translation)` changes the destination address of packets passing through the router, while :ref:`source-nat` changes the source address of packets. DNAT is typically used when an external (public) host needs to initiate a session with an internal (private) host. A customer needs to access a private service behind the routers public IP. A connection is established with the routers public IP address on a well known port and thus all traffic for this port is rewritten to address the internal (private) host. .. _bidirectional-nat: Bidirectional NAT ^^^^^^^^^^^^^^^^^ This is a common scenario where both :ref:`source-nat` and :ref:`destination-nat` are configured at the same time. It's commonly used when internal (private) hosts need to establish a connection with external resources and external systems need to access internal (private) resources. NAT, Routing, Firewall Interaction ---------------------------------- There is a very nice picture/explanation in the Vyatta documentation which should be rewritten here. NAT Ruleset ----------- :abbr:`NAT (Network Address Translation)` is configured entirely on a series of so called `rules`. Rules are numbered and evaluated by the underlying OS in numerical order! The rule numbers can be changes by utilizing the :cfgcmd:`rename` and :cfgcmd:`copy` commands. .. note:: Changes to the NAT system only affect newly established connections. Already established connections are not affected. .. hint:: When designing your NAT ruleset leave some space between consecutive rules for later extension. Your ruleset could start with numbers 10, 20, 30. You thus can later extend the ruleset and place new rules between existing ones. Rules will be created for both :ref:`source-nat` and :ref:`destination-nat`. For :ref:`bidirectional-nat` a rule for both :ref:`source-nat` and :ref:`destination-nat` needs to be created. .. _traffic-filters: Traffic Filters --------------- Traffic Filters are used to control which packets will have the defined NAT rules applied. Five different filters can be applied within a NAT rule. * **outbound-interface** - applicable only to :ref:`source-nat`. It configures the interface which is used for the outside traffic that this translation rule applies to. Interface groups, inverted selection and wildcard, are also supported. Examples: .. code-block:: none set nat source rule 20 outbound-interface interface-name eth0 set nat source rule 30 outbound-interface interface-name bond1* set nat source rule 20 outbound-interface interface-name !vtun2 set nat source rule 20 outbound-interface interface-group GROUP1 set nat source rule 20 outbound-interface interface-group !GROUP2 * **inbound-interface** - applicable only to :ref:`destination-nat`. It configures the interface which is used for the inside traffic the translation rule applies to. Interface groups, inverted selection and wildcard, are also supported. Example: .. code-block:: none set nat destination rule 20 inbound-interface interface-name eth0 set nat destination rule 30 inbound-interface interface-name bond1* set nat destination rule 20 inbound-interface interface-name !vtun2 set nat destination rule 20 inbound-interface interface-group GROUP1 set nat destination rule 20 inbound-interface interface-group !GROUP2 * **protocol** - specify which types of protocols this translation rule applies to. Only packets matching the specified protocol are NATed. By default this applies to `all` protocols. Example: * Set SNAT rule 20 to only NAT TCP and UDP packets * Set DNAT rule 20 to only NAT UDP packets .. code-block:: none set nat source rule 20 protocol tcp_udp set nat destination rule 20 protocol udp * **source** - specifies which packets the NAT translation rule applies to based on the packets source IP address and/or source port. Only matching packets are considered for NAT. Example: * Set SNAT rule 20 to only NAT packets arriving from the 192.0.2.0/24 network * Set SNAT rule 30 to only NAT packets arriving from the 203.0.113.0/24 network with a source port of 80 and 443 .. code-block:: none set nat source rule 20 source address 192.0.2.0/24 set nat source rule 30 source address 203.0.113.0/24 set nat source rule 30 source port 80,443 * **destination** - specify which packets the translation will be applied to, only based on the destination address and/or port number configured. .. note:: If no destination is specified the rule will match on any destination address and port. Example: * Configure SNAT rule (40) to only NAT packets with a destination address of 192.0.2.1. .. code-block:: none set nat source rule 40 destination address 192.0.2.1 Address Conversion ------------------ Every NAT rule has a translation command defined. The address defined for the translation is the address used when the address information in a packet is replaced. Source Address ^^^^^^^^^^^^^^ For :ref:`source-nat` rules the packets source address will be replaced with the address specified in the translation command. A port translation can also be specified and is part of the translation address. .. note:: The translation address must be set to one of the available addresses on the configured `outbound-interface` or it must be set to `masquerade` which will use the primary IP address of the `outbound-interface` as its translation address. .. note:: When using NAT for a large number of host systems it recommended that a minimum of 1 IP address is used to NAT every 256 private host systems. This is due to the limit of 65,000 port numbers available for unique translations and a reserving an average of 200-300 sessions per host system. Example: * Define a discrete source IP address of 100.64.0.1 for SNAT rule 20 * Use address `masquerade` (the interfaces primary address) on rule 30 * For a large amount of private machines behind the NAT your address pool might to be bigger. Use any address in the range 100.64.0.10 - 100.64.0.20 on SNAT rule 40 when doing the translation .. code-block:: none set nat source rule 20 translation address 100.64.0.1 set nat source rule 30 translation address 'masquerade' set nat source rule 40 translation address 100.64.0.10-100.64.0.20 Destination Address ^^^^^^^^^^^^^^^^^^^ For :ref:`destination-nat` rules the packets destination address will be replaced by the specified address in the `translation address` command. Example: * DNAT rule 10 replaces the destination address of an inbound packet with 192.0.2.10 .. code-block:: none set nat destination rule 10 translation address 192.0.2.10 Also, in :ref:`destination-nat`, redirection to localhost is supported. The redirect statement is a special form of dnat which always translates the destination address to the local host’s one. Example of redirection: .. code-block:: none set nat destination rule 10 translation redirect port 22 NAT Load Balance ---------------- Advanced configuration can be used in order to apply source or destination NAT, and within a single rule, be able to define multiple translated addresses, so NAT balances the translations among them. NAT Load Balance uses an algorithm that generates a hash and based on it, then it applies corresponding translation. This hash can be generated randomly, or can use data from the ip header: source-address, destination-address, source-port and/or destination-port. By default, it will generate the hash randomly. When defining the translated address, called ``backends``, a ``weight`` must be configured. This lets the user define load balance distribution according to their needs. Them sum of all the weights defined for the backends should be equal to 100. In oder words, the weight defined for the backend is the percentage of the connections that will receive such backend. .. cfgcmd:: set nat [source | destination] rule load-balance hash [source-address | destination-address | source-port | destination-port | random] .. cfgcmd:: set nat [source | destination] rule load-balance backend weight <1-100> Configuration Examples ====================== To setup SNAT, we need to know: * The internal IP addresses we want to translate * The outgoing interface to perform the translation on * The external IP address to translate to In the example used for the Quick Start configuration above, we demonstrate the following configuration: .. code-block:: none set nat source rule 100 outbound-interface interface-name 'eth0' set nat source rule 100 source address '192.168.0.0/24' set nat source rule 100 translation address 'masquerade' Which generates the following configuration: .. code-block:: none rule 100 { outbound-interface { interface-name eth0 } source { address 192.168.0.0/24 } translation { address masquerade } } In this example, we use **masquerade** as the translation address instead of an IP address. The **masquerade** target is effectively an alias to say "use whatever IP address is on the outgoing interface", rather than a statically configured IP address. This is useful if you use DHCP for your outgoing interface and do not know what the external address will be. When using NAT for a large number of host systems it recommended that a minimum of 1 IP address is used to NAT every 256 host systems. This is due to the limit of 65,000 port numbers available for unique translations and a reserving an average of 200-300 sessions per host system. Example: For an ~8,000 host network a source NAT pool of 32 IP addresses is recommended. A pool of addresses can be defined by using a hyphen between two IP addresses: .. code-block:: none set nat source rule 100 translation address '203.0.113.32-203.0.113.63' .. _avoidng_leaky_nat: Avoiding "leaky" NAT -------------------- Linux netfilter will not NAT traffic marked as INVALID. This often confuses people into thinking that Linux (or specifically VyOS) has a broken NAT implementation because non-NATed traffic is seen leaving an external interface. This is actually working as intended, and a packet capture of the "leaky" traffic should reveal that the traffic is either an additional TCP "RST", "FIN,ACK", or "RST,ACK" sent by client systems after Linux netfilter considers the connection closed. The most common is the additional TCP RST some host implementations send after terminating a connection (which is implementation-specific). In other words, connection tracking has already observed the connection be closed and has transition the flow to INVALID to prevent attacks from attempting to reuse the connection. You can avoid the "leaky" behavior by using a firewall policy that drops "invalid" state packets. Having control over the matching of INVALID state traffic, e.g. the ability to selectively log, is an important troubleshooting tool for observing broken protocol behavior. For this reason, VyOS does not globally drop invalid state traffic, instead allowing the operator to make the determination on how the traffic is handled. .. _hairpin_nat_reflection: Hairpin NAT/NAT Reflection -------------------------- A typical problem with using NAT and hosting public servers is the ability for internal systems to reach an internal server using it's external IP address. The solution to this is usually the use of split-DNS to correctly point host systems to the internal address when requests are made internally. Because many smaller networks lack DNS infrastructure, a work-around is commonly deployed to facilitate the traffic by NATing the request from internal hosts to the source address of the internal interface on the firewall. This technique is commonly referred to as NAT Reflection or Hairpin NAT. Example: * Redirect Microsoft RDP traffic from the outside (WAN, external) world via :ref:`destination-nat` in rule 100 to the internal, private host 192.0.2.40. * Redirect Microsoft RDP traffic from the internal (LAN, private) network via :ref:`destination-nat` in rule 110 to the internal, private host 192.0.2.40. We also need a :ref:`source-nat` rule 110 for the reverse path of the traffic. The internal network 192.0.2.0/24 is reachable via interface `eth0.10`. .. code-block:: none set nat destination rule 100 description 'Regular destination NAT from external' set nat destination rule 100 destination port '3389' set nat destination rule 100 inbound-interface interface-name 'pppoe0' set nat destination rule 100 protocol 'tcp' set nat destination rule 100 translation address '192.0.2.40' set nat destination rule 110 description 'NAT Reflection: INSIDE' set nat destination rule 110 destination port '3389' set nat destination rule 110 inbound-interface interface-name 'eth0.10' set nat destination rule 110 protocol 'tcp' set nat destination rule 110 translation address '192.0.2.40' set nat source rule 110 description 'NAT Reflection: INSIDE' set nat source rule 110 destination address '192.0.2.0/24' set nat source rule 110 outbound-interface interface-name 'eth0.10' set nat source rule 110 protocol 'tcp' set nat source rule 110 source address '192.0.2.0/24' set nat source rule 110 translation address 'masquerade' Which results in a configuration of: .. code-block:: none vyos@vyos# show nat destination { rule 100 { description "Regular destination NAT from external" destination { port 3389 } inbound-interface { interface-name pppoe0 } protocol tcp translation { address 192.0.2.40 } } rule 110 { description "NAT Reflection: INSIDE" destination { port 3389 } inbound-interface { interface-name eth0.10 } protocol tcp translation { address 192.0.2.40 } } } source { rule 110 { description "NAT Reflection: INSIDE" destination { address 192.0.2.0/24 } outbound-interface { interface-name eth0.10 } protocol tcp source { address 192.0.2.0/24 } translation { address masquerade } } } Destination NAT --------------- DNAT is typically referred to as a **Port Forward**. When using VyOS as a NAT router and firewall, a common configuration task is to redirect incoming traffic to a system behind the firewall. In this example, we will be using the example Quick Start configuration above as a starting point. To setup a destination NAT rule we need to gather: * The interface traffic will be coming in on; * The protocol and port we wish to forward; * The IP address of the internal system we wish to forward traffic to. In our example, we will be forwarding web server traffic to an internal web server on 192.168.0.100. HTTP traffic makes use of the TCP protocol on port 80. For other common port numbers, see: https://en.wikipedia.org/wiki/List_of_TCP_and_UDP_port_numbers Our configuration commands would be: .. code-block:: none set nat destination rule 10 description 'Port Forward: HTTP to 192.168.0.100' set nat destination rule 10 destination port '80' set nat destination rule 10 inbound-interface interface-name 'eth0' set nat destination rule 10 protocol 'tcp' set nat destination rule 10 translation address '192.168.0.100' Which would generate the following NAT destination configuration: .. code-block:: none nat { destination { rule 10 { description "Port Forward: HTTP to 192.168.0.100" destination { port 80 } inbound-interface { interface-name eth0 } protocol tcp translation { address 192.168.0.100 } } } } .. note:: If forwarding traffic to a different port than it is arriving on, you may also configure the translation port using `set nat destination rule [n] translation port`. This establishes our Port Forward rule, but if we created a firewall policy it will likely block the traffic. Firewall rules for Destination NAT ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ It is important to note that when creating firewall rules, the DNAT translation occurs **before** traffic traverses the firewall. In other words, the destination address has already been translated to 192.168.0.100. So in our firewall ruleset, we want to allow traffic which previously matched a destination nat rule. In order to avoid creating many rules, one for each destination nat rule, we can accept all **'dnat'** connections with one simple rule, using ``connection-status`` matcher: .. code-block:: none set firewall ipv4 forward filter rule 10 action accept set firewall ipv4 forward filter rule 10 connection-status nat destination set firewall ipv4 forward filter rule 10 state new enable This would generate the following configuration: .. code-block:: none ipv4 { forward { filter { rule 10 { action accept connection-status { nat destination } state { new enable } } } } } 1-to-1 NAT ---------- Another term often used for DNAT is **1-to-1 NAT**. For a 1-to-1 NAT configuration, both DNAT and SNAT are used to NAT all traffic from an external IP address to an internal IP address and vice-versa. Typically, a 1-to-1 NAT rule omits the destination port (all ports) and replaces the protocol with either **all** or **ip**. Then a corresponding SNAT rule is created to NAT outgoing traffic for the internal IP to a reserved external IP. This dedicates an external IP address to an internal IP address and is useful for protocols which don't have the notion of ports, such as GRE. Here's an extract of a simple 1-to-1 NAT configuration with one internal and one external interface: .. code-block:: none set interfaces ethernet eth0 address '192.168.1.1/24' set interfaces ethernet eth0 description 'Inside interface' set interfaces ethernet eth1 address '192.0.2.30/24' set interfaces ethernet eth1 description 'Outside interface' set nat destination rule 2000 description '1-to-1 NAT example' set nat destination rule 2000 destination address '192.0.2.30' set nat destination rule 2000 inbound-interface interface-name 'eth1' set nat destination rule 2000 translation address '192.168.1.10' set nat source rule 2000 description '1-to-1 NAT example' set nat source rule 2000 outbound-interface interface-name 'eth1' set nat source rule 2000 source address '192.168.1.10' set nat source rule 2000 translation address '192.0.2.30' Firewall rules are written as normal, using the internal IP address as the source of outbound rules and the destination of inbound rules. NAT before VPN -------------- Some application service providers (ASPs) operate a VPN gateway to provide access to their internal resources, and require that a connecting organisation translate all traffic to the service provider network to a source address provided by the ASP. Load Balance ------------ Here we provide two examples on how to apply NAT Load Balance. First scenario: apply destination NAT for all HTTP traffic comming through interface eth0, and user 4 backends. First backend should received 30% of the request, second backend should get 20%, third 15% and the fourth 35% We will use source and destination address for hash generation. .. code-block:: none set nat destination rule 10 inbound-interface inbound-interface eth0 set nat destination rule 10 protocol tcp set nat destination rule 10 destination port 80 set nat destination rule 10 load-balance hash source-address set nat destination rule 10 load-balance hash destination-address set nat destination rule 10 laod-balance backend 198.51.100.101 weight 30 set nat destination rule 10 laod-balance backend 198.51.100.102 weight 20 set nat destination rule 10 laod-balance backend 198.51.100.103 weight 15 set nat destination rule 10 laod-balance backend 198.51.100.104 weight 35 Second scenario: apply source NAT for all outgoing connections from LAN 10.0.0.0/8, using 3 public addresses and equal distribution. We will generate the hash randomly. .. code-block:: none set nat source rule 10 outbound-interface interface-name eth0 set nat source rule 10 source address 10.0.0.0/8 set nat source rule 10 load-balance hash random set nat source rule 10 load-balance backend 192.0.2.251 weight 33 set nat source rule 10 load-balance backend 192.0.2.252 weight 33 set nat source rule 10 load-balance backend 192.0.2.253 weight 34 Example Network ^^^^^^^^^^^^^^^ Here's one example of a network environment for an ASP. The ASP requests that all connections from this company should come from 172.29.41.89 - an address that is assigned by the ASP and not in use at the customer site. .. figure:: /_static/images/nat_before_vpn_topology.png :scale: 100 % :alt: NAT before VPN Topology NAT before VPN Topology Configuration ^^^^^^^^^^^^^ The required configuration can be broken down into 4 major pieces: * A dummy interface for the provider-assigned IP; * NAT (specifically, Source NAT); * IPSec IKE and ESP Groups; * IPSec VPN tunnels. Dummy interface """"""""""""""" The dummy interface allows us to have an equivalent of the Cisco IOS Loopback interface - a router-internal interface we can use for IP addresses the router must know about, but which are not actually assigned to a real network. We only need a single step for this interface: .. code-block:: none set interfaces dummy dum0 address '172.29.41.89/32' NAT Configuration """"""""""""""""" .. code-block:: none set nat source rule 110 description 'Internal to ASP' set nat source rule 110 destination address '172.27.1.0/24' set nat source rule 110 source address '192.168.43.0/24' set nat source rule 110 translation address '172.29.41.89' set nat source rule 120 description 'Internal to ASP' set nat source rule 120 destination address '10.125.0.0/16' set nat source rule 120 source address '192.168.43.0/24' set nat source rule 120 translation address '172.29.41.89' IPSec IKE and ESP """"""""""""""""" The ASP has documented their IPSec requirements: * IKE Phase: * aes256 Encryption * sha256 Hashes * ESP Phase: * aes256 Encryption * sha256 Hashes * DH Group 14 Additionally, we want to use VPNs only on our eth1 interface (the external interface in the image above) .. code-block:: none set vpn ipsec ike-group my-ike key-exchange 'ikev1' set vpn ipsec ike-group my-ike lifetime '7800' set vpn ipsec ike-group my-ike proposal 1 dh-group '14' set vpn ipsec ike-group my-ike proposal 1 encryption 'aes256' set vpn ipsec ike-group my-ike proposal 1 hash 'sha256' set vpn ipsec esp-group my-esp lifetime '3600' set vpn ipsec esp-group my-esp mode 'tunnel' set vpn ipsec esp-group my-esp pfs 'disable' set vpn ipsec esp-group my-esp proposal 1 encryption 'aes256' set vpn ipsec esp-group my-esp proposal 1 hash 'sha256' set vpn ipsec interface 'eth1' IPSec VPN Tunnels """"""""""""""""" We'll use the IKE and ESP groups created above for this VPN. Because we need access to 2 different subnets on the far side, we will need two different tunnels. If you changed the names of the ESP group and IKE group in the previous step, make sure you use the correct names here too. .. code-block:: none set vpn ipsec authentication psk vyos id '203.0.113.46' set vpn ipsec authentication psk vyos id '198.51.100.243' set vpn ipsec authentication psk vyos secret 'MYSECRETPASSWORD' set vpn ipsec site-to-site peer branch authentication local-id '203.0.113.46' set vpn ipsec site-to-site peer branch authentication mode 'pre-shared-secret' set vpn ipsec site-to-site peer branch authentication remote-id '198.51.100.243' set vpn ipsec site-to-site peer branch connection-type 'initiate' set vpn ipsec site-to-site peer branch default-esp-group 'my-esp' set vpn ipsec site-to-site peer branch ike-group 'my-ike' set vpn ipsec site-to-site peer branch ikev2-reauth 'inherit' set vpn ipsec site-to-site peer branch local-address '203.0.113.46' set vpn ipsec site-to-site peer branch remote-address '198.51.100.243' set vpn ipsec site-to-site peer branch tunnel 0 local prefix '172.29.41.89/32' set vpn ipsec site-to-site peer branch tunnel 0 remote prefix '172.27.1.0/24' set vpn ipsec site-to-site peer branch tunnel 1 local prefix '172.29.41.89/32' set vpn ipsec site-to-site peer branch tunnel 1 remote prefix '10.125.0.0/16' Testing and Validation """""""""""""""""""""" If you've completed all the above steps you no doubt want to see if it's all working. Start by checking for IPSec SAs (Security Associations) with: .. code-block:: none $ show vpn ipsec sa Peer ID / IP Local ID / IP ------------ ------------- 198.51.100.243 203.0.113.46 Tunnel State Bytes Out/In Encrypt Hash NAT-T A-Time L-Time Proto ------ ----- ------------- ------- ---- ----- ------ ------ ----- 0 up 0.0/0.0 aes256 sha256 no 1647 3600 all 1 up 0.0/0.0 aes256 sha256 no 865 3600 all That looks good - we defined 2 tunnels and they're both up and running.