.. _routing-static: ###### Static ###### Static routes are manually configured routes, which, in general, cannot be updated dynamically from information VyOS learns about the network topology from other routing protocols. However, if a link fails, the router will remove routes, including static routes, from the :abbr:`RIPB (Routing Information Base)` that used this interface to reach the next hop. In general, static routes should only be used for very simple network topologies, or to override the behavior of a dynamic routing protocol for a small number of routes. The collection of all routes the router has learned from its configuration or from its dynamic routing protocols is stored in the RIB. Unicast routes are directly used to determine the forwarding table used for unicast packet forwarding. ************* Static Routes ************* .. cfgcmd:: set protocols static route next-hop
Configure next-hop `
` for an IPv4 static route. Multiple static routes can be created. .. cfgcmd:: set protocols static route next-hop
disable Disable this IPv4 static route entry. .. cfgcmd:: set protocols static route next-hop
distance Defines next-hop distance for this route, routes with smaller administrative distance are elected prior to those with a higher distance. Range is 1 to 255, default is 1. .. note:: Routes with a distance of 255 are effectively disabled and not installed into the kernel. .. cfgcmd:: set protocols static route6 next-hop
Configure next-hop `
` for an IPv6 static route. Multiple static routes can be created. .. cfgcmd:: set protocols static route6 next-hop
disable Disable this IPv6 static route entry. .. cfgcmd:: set protocols static route6 next-hop
distance Defines next-hop distance for this route, routes with smaller administrative distance are elected prior to those with a higher distance. Range is 1 to 255, default is 1. .. note:: Routes with a distance of 255 are effectively disabled and not installed into the kernel. Interface Routes ================ .. cfgcmd:: set protocols static route interface Allows you to configure the next-hop interface for an interface-based IPv4 static route. `` will be the next-hop interface where traffic is routed for the given ``. .. cfgcmd:: set protocols static route interface disable Disables interface-based IPv4 static route. .. cfgcmd:: set protocols static route interface distance Defines next-hop distance for this route, routes with smaller administrative distance are elected prior to those with a higher distance. Range is 1 to 255, default is 1. .. cfgcmd:: set protocols static route6 interface Allows you to configure the next-hop interface for an interface-based IPv6 static route. `` will be the next-hop interface where traffic is routed for the given ``. .. cfgcmd:: set protocols static route6 interface disable Disables interface-based IPv6 static route. .. cfgcmd:: set protocols static route6 interface distance Defines next-hop distance for this route, routes with smaller administrative distance are elected prior to those with a higher distance. Range is 1 to 255, default is 1. Blackhole ========= .. cfgcmd:: set protocols static route blackhole Use this command to configure a "black-hole" route on the router. A black-hole route is a route for which the system silently discard packets that are matched. This prevents networks leaking out public interfaces, but it does not prevent them from being used as a more specific route inside your network. .. cfgcmd:: set protocols static route blackhole distance Defines blackhole distance for this route, routes with smaller administrative distance are elected prior to those with a higher distance. .. cfgcmd:: set protocols static route6 blackhole Use this command to configure a "black-hole" route on the router. A black-hole route is a route for which the system silently discard packets that are matched. This prevents networks leaking out public interfaces, but it does not prevent them from being used as a more specific route inside your network. .. cfgcmd:: set protocols static route6 blackhole distance Defines blackhole distance for this route, routes with smaller administrative distance are elected prior to those with a higher distance. Alternate Routing Tables ======================== TBD Alternate routing tables are used with policy based routing by utilizing :ref:`vrf`. .. _routing-arp: ### ARP ### :abbr:`ARP (Address Resolution Protocol)` is a communication protocol used for discovering the link layer address, such as a MAC address, associated with a given internet layer address, typically an IPv4 address. This mapping is a critical function in the Internet protocol suite. ARP was defined in 1982 by :rfc:`826` which is Internet Standard STD 37. In Internet Protocol Version 6 (IPv6) networks, the functionality of ARP is provided by the Neighbor Discovery Protocol (NDP). To manipulate or display ARP_ table entries, the following commands are implemented. ********* Configure ********* .. cfgcmd:: set protocols static arp
hwaddr This will configure a static ARP entry always resolving `
` to ``. Example: .. code-block:: none set protocols static arp 192.0.2.100 hwaddr 00:53:27:de:23:aa ********* Operation ********* .. opcmd:: show protocols static arp Display all known ARP table entries spanning across all interfaces .. code-block:: none vyos@vyos:~$ show protocols static arp Address HWtype HWaddress Flags Mask Iface 10.1.1.1 ether 00:53:00:de:23:2e C eth1 10.1.1.100 ether 00:53:00:de:23:aa CM eth1 .. opcmd:: show protocols static arp interface eth1 Display all known ARP table entries on a given interface only (`eth1`): .. code-block:: none vyos@vyos:~$ show protocols static arp interface eth1 Address HWtype HWaddress Flags Mask Iface 10.1.1.1 ether 00:53:00:de:23:2e C eth1 10.1.1.100 ether 00:53:00:de:23:aa CM eth1 .. _ARP: https://en.wikipedia.org/wiki/Address_Resolution_Protocol