.. _bond-interface: #### Bond #### The bonding interface provides a method for aggregating multiple network interfaces into a single logical "bonded" interface, or LAG, or ether-channel, or port-channel. The behavior of the bonded interfaces depends upon the mode; generally speaking, modes provide either hot standby or load balancing services. Additionally, link integrity monitoring may be performed. Configuration ############# Address ------- .. cfgcmd:: set interfaces bonding address
Configure interface `` with one or more interface addresses. * **address** can be specified multiple times as IPv4 and/or IPv6 address, e.g. 192.0.2.1/24 and/or 2001:db8::1/64 * **dhcp** interface address is received by DHCP from a DHCP server on this segment. * **dhcpv6** interface address is received by DHCPv6 from a DHCPv6 server on this segment. Example: .. code-block:: none set interfaces bonding bond0 address 192.0.2.1/24 set interfaces bonding bond0 address 192.0.2.2/24 set interfaces bonding bond0 address 2001:db8::ffff/64 set interfaces bonding bond0 address 2001:db8:100::ffff/64 .. cfgcmd:: set interfaces bonding ipv6 address autoconf :abbr:`SLAAC (Stateless Address Autoconfiguration)` :rfc:`4862`. IPv6 hosts can configure themselves automatically when connected to an IPv6 network using the Neighbor Discovery Protocol via :abbr:`ICMPv6 (Internet Control Message Protocol version 6)` router discovery messages. When first connected to a network, a host sends a link-local router solicitation multicast request for its configuration parameters; routers respond to such a request with a router advertisement packet that contains Internet Layer configuration parameters. .. note:: This method automatically disables IPv6 traffic forwarding on the interface in question. .. cfgcmd:: set interfaces bonding ipv6 address eui64 :abbr:`EUI-64 (64-Bit Extended Unique Identifier)` as specified in :rfc:`4291` allows a host to assign iteslf a unique 64-Bit IPv6 address. .. code-block:: none set interfaces bonding bond0 ipv6 address eui64 2001:db8:beef::/64 Link Administration ------------------- .. cfgcmd:: set interfaces bonding description Assign given `` to interface. Description will also be passed to SNMP monitoring systems. .. cfgcmd:: set interfaces bonding disable Disable given ``. It will be placed in administratively down (``A/D``) state. .. cfgcmd:: set interfaces bonding mac Configure user defined :abbr:`MAC (Media Access Control)` address on given ``. .. cfgcmd:: set interfaces bonding mode Specifies one of the bonding policies. The default is 802.3ad. Possible values are: * **802.3ad** - IEEE 802.3ad Dynamic link aggregation. Creates aggregation groups that share the same speed and duplex settings. Utilizes all slaves in the active aggregator according to the 802.3ad specification. Slave selection for outgoing traffic is done according to the transmit hash policy, which may be changed from the default simple XOR policy via the :cfgcmd:`hash-policy` option, documented below. .. note:: Not all transmit policies may be 802.3ad compliant, particularly in regards to the packet mis-ordering requirements of section 43.2.4 of the 802.3ad standard. * **active-backup** - Active-backup policy: Only one slave in the bond is active. A different slave becomes active if, and only if, the active slave fails. The bond's MAC address is externally visible on only one port (network adapter) to avoid confusing the switch. When a failover occurs in active-backup mode, bonding will issue one or more gratuitous ARPs on the newly active slave. One gratuitous ARP is issued for the bonding master interface and each VLAN interfaces configured above it, provided that the interface has at least one IP address configured. Gratuitous ARPs issued for VLAN interfaces are tagged with the appropriate VLAN id. This mode provides fault tolerance. The :cfgcmd:`primary` option, documented below, affects the behavior of this mode. * **broadcast** - Broadcast policy: transmits everything on all slave interfaces. This mode provides fault tolerance. * **round-robin** - Round-robin policy: Transmit packets in sequential order from the first available slave through the last. This mode provides load balancing and fault tolerance. * **transmit-load-balance** - Adaptive transmit load balancing: channel bonding that does not require any special switch support. Incoming traffic is received by the current slave. If the receiving slave fails, another slave takes over the MAC address of the failed receiving slave. * **adaptive-load-balance** - Adaptive load balancing: includes transmit-load-balance plus receive load balancing for IPV4 traffic, and does not require any special switch support. The receive load balancing is achieved by ARP negotiation. The bonding driver intercepts the ARP Replies sent by the local system on their way out and overwrites the source hardware address with the unique hardware address of one of the slaves in the bond such that different peers use different hardware addresses for the server. Receive traffic from connections created by the server is also balanced. When the local system sends an ARP Request the bonding driver copies and saves the peer's IP information from the ARP packet. When the ARP Reply arrives from the peer, its hardware address is retrieved and the bonding driver initiates an ARP reply to this peer assigning it to one of the slaves in the bond. A problematic outcome of using ARP negotiation for balancing is that each time that an ARP request is broadcast it uses the hardware address of the bond. Hence, peers learn the hardware address of the bond and the balancing of receive traffic collapses to the current slave. This is handled by sending updates (ARP Replies) to all the peers with their individually assigned hardware address such that the traffic is redistributed. Receive traffic is also redistributed when a new slave is added to the bond and when an inactive slave is re-activated. The receive load is distributed sequentially (round robin) among the group of highest speed slaves in the bond. When a link is reconnected or a new slave joins the bond the receive traffic is redistributed among all active slaves in the bond by initiating ARP Replies with the selected MAC address to each of the clients. The updelay parameter (detailed below) must be set to a value equal or greater than the switch's forwarding delay so that the ARP Replies sent to the peers will not be blocked by the switch. * **xor-hash** - XOR policy: Transmit based on the selected transmit hash policy. The default policy is a simple [(source MAC address XOR'd with destination MAC address XOR packet type ID) modulo slave count]. Alternate transmit policies may be selected via the :cfgcmd:`hash-policy` option, described below. This mode provides load balancing and fault tolerance. .. cfgcmd:: set interfaces bonding hash-policy * **layer2** - Uses XOR of hardware MAC addresses and packet type ID field to generate the hash. The formula is .. code-block:: none hash = source MAC XOR destination MAC XOR packet type ID slave number = hash modulo slave count This algorithm will place all traffic to a particular network peer on the same slave. This algorithm is 802.3ad compliant. * **layer2+3** - This policy uses a combination of layer2 and layer3 protocol information to generate the hash. Uses XOR of hardware MAC addresses and IP addresses to generate the hash. The formula is: .. code-block:: none hash = source MAC XOR destination MAC XOR packet type ID hash = hash XOR source IP XOR destination IP hash = hash XOR (hash RSHIFT 16) hash = hash XOR (hash RSHIFT 8) And then hash is reduced modulo slave count. If the protocol is IPv6 then the source and destination addresses are first hashed using ipv6_addr_hash. This algorithm will place all traffic to a particular network peer on the same slave. For non-IP traffic, the formula is the same as for the layer2 transmit hash policy. This policy is intended to provide a more balanced distribution of traffic than layer2 alone, especially in environments where a layer3 gateway device is required to reach most destinations. This algorithm is 802.3ad compliant. * **layer3+4** - This policy uses upper layer protocol information, when available, to generate the hash. This allows for traffic to a particular network peer to span multiple slaves, although a single connection will not span multiple slaves. The formula for unfragmented TCP and UDP packets is .. code-block:: none hash = source port, destination port (as in the header) hash = hash XOR source IP XOR destination IP hash = hash XOR (hash RSHIFT 16) hash = hash XOR (hash RSHIFT 8) And then hash is reduced modulo slave count. If the protocol is IPv6 then the source and destination addresses are first hashed using ipv6_addr_hash. For fragmented TCP or UDP packets and all other IPv4 and IPv6 protocol traffic, the source and destination port information is omitted. For non-IP traffic, the formula is the same as for the layer2 transmit hash policy. This algorithm is not fully 802.3ad compliant. A single TCP or UDP conversation containing both fragmented and unfragmented packets will see packets striped across two interfaces. This may result in out of order delivery. Most traffic types will not meet this criteria, as TCP rarely fragments traffic, and most UDP traffic is not involved in extended conversations. Other implementations of 802.3ad may or may not tolerate this noncompliance. .. cfgcmd:: set interfaces bonding primary An `` specifying which slave is the primary device. The specified device will always be the active slave while it is available. Only when the primary is off-line will alternate devices be used. This is useful when one slave is preferred over another, e.g., when one slave has higher throughput than another. The primary option is only valid for active-backup, transmit-load-balance, and adaptive-load-balance mode. .. cfgcmd:: set interfaces bonding arp-monitor interval