.. _ip-commands: ########### IP commands ########### IPv4 ==== System configuration commands ----------------------------- .. cfgcmd:: set system ip disable-forwarding Use this command to disable IPv4 forwarding on all interfaces. .. cfgcmd:: set system ip arp table-size Use this command to define the maximum number of entries to keep in the ARP cache (1024, 2048, 4096, 8192, 16384, 32768). .. cfgcmd:: set system ip multipath layer4-hashing Use this command to use Layer 4 information for IPv4 ECMP hashing. Operational commands -------------------- show commands ^^^^^^^^^^^^^ See below the different parameters available for the IPv4 **show** command: .. code-block:: none vyos@vyos:~$ show ip Possible completions: access-list Show all IP access-lists as-path-access-list Show all as-path-access-lists bgp Show Border Gateway Protocol (BGP) information community-list Show IP community-lists extcommunity-list Show extended IP community-lists forwarding Show IP forwarding status groups Show IP multicast group membership igmp Show IGMP (Internet Group Management Protocol) information large-community-list Show IP large-community-lists multicast Show IP multicast ospf Show IPv4 Open Shortest Path First (OSPF) routing information pim Show PIM (Protocol Independent Multicast) information ports Show IP ports in use by various system services prefix-list Show all IP prefix-lists protocol Show IP route-maps per protocol rip Show Routing Information Protocol (RIP) information route Show IP routes reset commands ^^^^^^^^^^^^^^ And the different IPv4 **reset** commands available: .. code-block:: none vyos@vyos:~$ reset ip Possible completions: arp Reset Address Resolution Protocol (ARP) cache bgp Clear Border Gateway Protocol (BGP) statistics or status igmp IGMP clear commands multicast IP multicast routing table route Reset IP route IPv6 ==== System configuration commands ----------------------------- .. cfgcmd:: set system ipv6 disable Use this command to disable assignment of IPv6 addresses on all interfaces. .. cfgcmd:: set system ipv6 disable-forwarding Use this command to disable IPv6 forwarding on all interfaces. .. cfgcmd:: set system ipv6 neighbor table-size Use this command to define the maximum number of entries to keep in the Neighbor cache (1024, 2048, 4096, 8192, 16384, 32768). .. cfgcmd:: set system ipv6 strict-dad Use this command to disable IPv6 operation on interface when Duplicate Address Detection fails on Link-Local address. .. cfgcmd:: set system ipv6 multipath layer4-hashing Use this command to user Layer 4 information for ECMP hashing. Operational commands -------------------- Show commands ^^^^^^^^^^^^^ .. opcmd:: show ipv6 neighbors Use this command to show IPv6 Neighbor Discovery Protocol information. .. opcmd:: show ipv6 groups Use this command to show IPv6 multicast group membership. .. opcmd:: show ipv6 forwarding Use this command to show IPv6 forwarding status. .. opcmd:: show ipv6 route Use this command to show IPv6 routes. Check the many parameters available for the `show ipv6 route` command: .. code-block:: none vyos@vyos:~$ show ipv6 route Possible completions: Execute the current command Show IPv6 routes of given address or prefix bgp Show IPv6 BGP routes cache Show kernel IPv6 route cache connected Show IPv6 connected routes forward Show kernel IPv6 route table isis Show IPv6 ISIS routes kernel Show IPv6 kernel routes ospfv3 Show IPv6 OSPF6 routes ripng Show IPv6 RIPNG routes static Show IPv6 static routes summary Show IPv6 routes summary table Show IP routes in policy table vrf Show IPv6 routes in VRF .. opcmd:: show ipv6 prefix-list Use this command to show all IPv6 prefix lists There are different parameters for getting prefix-list information: .. code-block:: none vyos@vyos:~$ show ipv6 prefix-list Possible completions: Execute the current command Show specified IPv6 prefix-list detail Show detail of IPv6 prefix-lists summary Show summary of IPv6 prefix-lists .. opcmd:: show ipv6 access-list Use this command to show all IPv6 access lists You can also specify which IPv6 access-list should be shown: .. code-block:: none vyos@vyos:~$ show ipv6 access-list Possible completions: Execute the current command Show specified IPv6 access-list .. opcmd:: show ipv6 bgp Use this command to show IPv6 Border Gateway Protocol information. In addition, you can specify many other parameters to get BGP information: .. code-block:: none vyos@vyos:~$ show ipv6 bgp Possible completions: Execute the current command Show BGP information for given address or prefix community Show routes matching the communities community-list Show routes matching the community-list filter-list Show routes conforming to the filter-list large-community Show routes matching the large-community-list large-community-list neighbors Show detailed information on TCP and BGP neighbor connections prefix-list Show routes matching the prefix-list regexp Show routes matching the AS path regular expression route-map Show BGP routes matching the specified route map summary Show summary of BGP neighbor status .. opcmd:: show ipv6 ospfv3 Use this command to get information about OSPFv3. You can get more specific OSPFv3 information by using the parameters shown below: .. code-block:: none vyos@vyos:~$ show ipv6 ospfv3 Possible completions: Execute the current command area Show OSPFv3 spf-tree information border-routers Show OSPFv3 border-router (ABR and ASBR) information database Show OSPFv3 Link state database information interface Show OSPFv3 interface information linkstate Show OSPFv3 linkstate routing information neighbor Show OSPFv3 neighbor information redistribute Show OSPFv3 redistribute External information route Show OSPFv3 routing table information .. opcmd:: show ipv6 ripng Use this command to get information about the RIPNG protocol .. opcmd:: show ipv6 ripng status Use this command to show the status of the RIPNG protocol Reset commands ^^^^^^^^^^^^^^ .. opcmd:: reset ipv6 bgp
Use this command to clear Border Gateway Protocol statistics or status. .. opcmd:: reset ipv6 neighbors
Use this command to reset IPv6 Neighbor Discovery Protocol cache for an address or interface. .. opcmd:: reset ipv6 route cache Use this command to flush the kernel IPv6 route cache. An address can be added to flush it only for that route.