1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
|
.. cfgcmd:: set interfaces {{ var0 }} <interface> {{ var2 }} {{ var3 }}
{{ var5 }} {{ var6 }} ip arp-cache-timeout
Once a neighbor has been found, the entry is considered to be valid for at
least for this specifc time. An entry's validity will be extended if it
receives positive feedback from higher level protocols.
This defaults to 30 seconds.
Example:
.. code-block:: none
set interfaces {{ var0 }} {{ var1 }} {{ var2 }} {{ var4 }} {{ var5 }} {{ var7 }} ip arp-cache-timeout 180
.. cfgcmd:: set interfaces {{ var0 }} <interface> {{ var2 }} {{ var3 }}
{{ var5 }} {{ var6 }} ip disable-arp-filter
If set the kernel can respond to arp requests with addresses from other
interfaces. This may seem wrong but it usually makes sense, because it
increases the chance of successful communication. IP addresses are owned by
the complete host on Linux, not by particular interfaces. Only for more
complex setups like load-balancing, does this behaviour cause problems.
If not set (default) allows you to have multiple network interfaces on the
same subnet, and have the ARPs for each interface be answered based on whether
or not the kernel would route a packet from the ARP'd IP out that interface
(therefore you must use source based routing for this to work).
In other words it allows control of which cards (usually 1) will respond to an
arp request.
Example:
.. code-block:: none
set interfaces {{ var0 }} {{ var1 }} {{ var2 }} {{ var4 }} {{ var5 }} {{ var7 }} ip disable-arp-filter
.. cfgcmd:: set interfaces {{ var0 }} <interface> {{ var2 }} {{ var3 }}
{{ var5 }} {{ var6 }} ip disable-forwarding
Configure interface-specific Host/Router behaviour. If set, the interface will
switch to host mode and IPv6 forwarding will be disabled on this interface.
.. code-block:: none
set interfaces {{ var0 }} {{ var1 }} {{ var2 }} {{ var4 }} {{ var5 }} {{ var7 }} ip disable-forwarding
.. cfgcmd:: set interfaces {{ var0 }} <interface> {{ var2 }} {{ var3 }}
{{ var5 }} {{ var6 }} ip enable-arp-accept
Define behavior for gratuitous ARP frames who's IP is not already present in
the ARP table. If configured create new entries in the ARP table.
Both replies and requests type gratuitous arp will trigger the ARP table to be
updated, if this setting is on.
If the ARP table already contains the IP address of the gratuitous arp frame,
the arp table will be updated regardless if this setting is on or off.
.. code-block:: none
set interfaces {{ var0 }} {{ var1 }} {{ var2 }} {{ var4 }} {{ var5 }} {{ var7 }} ip enable-arp-accept
.. cfgcmd:: set interfaces {{ var0 }} <interface> {{ var2 }} {{ var3 }}
{{ var5 }} {{ var6 }} ip enable-arp-announce
Define different restriction levels for announcing the local source IP address
from IP packets in ARP requests sent on interface.
Use any local address, configured on any interface if this is not set.
If configured, try to avoid local addresses that are not in the target's
subnet for this interface. This mode is useful when target hosts reachable via
this interface require the source IP address in ARP requests to be part of
their logical network configured on the receiving interface. When we generate
the request we will check all our subnets that include the target IP and will
preserve the source address if it is from such subnet. If there is no such
subnet we select source address according to the rules for level 2.
.. code-block:: none
set interfaces {{ var0 }} {{ var1 }} {{ var2 }} {{ var4 }} {{ var5 }} {{ var7 }} ip enable-arp-announce
.. cfgcmd:: set interfaces {{ var0 }} <interface> {{ var2 }} {{ var3 }}
{{ var5 }} {{ var6 }} ip enable-arp-ignore
Define different modes for sending replies in response to received ARP
requests that resolve local target IP addresses:
If configured, reply only if the target IP address is local address configured
on the incoming interface.
If this option is unset (default), reply for any local target IP address,
configured on any interface.
.. code-block:: none
set interfaces {{ var0 }} {{ var1 }} {{ var2 }} {{ var4 }} {{ var5 }} {{ var7 }} ip enable-arp-ignore
.. cfgcmd:: set interfaces {{ var0 }} <interface> {{ var2 }} {{ var3 }}
{{ var5 }} {{ var6 }} ip enable-proxy-arp
Use this command to enable proxy Address Resolution Protocol (ARP) on this
interface. Proxy ARP allows an Ethernet interface to respond with its own
:abbr:`MAC (Media Access Control)` address to ARP requests for destination IP
addresses on subnets attached to other interfaces on the system. Subsequent
packets sent to those destination IP addresses are forwarded appropriately by
the system.
Example:
.. code-block:: none
set interfaces {{ var0 }} {{ var1 }} {{ var2 }} {{ var4 }} {{ var5 }} {{ var7 }} ip enable-proxy-arp
.. cfgcmd:: set interfaces {{ var0 }} <interface> {{ var2 }} {{ var3 }}
{{ var5 }} {{ var6 }} ip proxy-arp-pvlan
Private VLAN proxy arp. Basically allow proxy arp replies back to the same
interface (from which the ARP request/solicitation was received).
This is done to support (ethernet) switch features, like :rfc:`3069`, where
the individual ports are NOT allowed to communicate with each other, but they
are allowed to talk to the upstream router. As described in :rfc:`3069`, it is
possible to allow these hosts to communicate through the upstream router by
proxy_arp'ing.
.. note:: Does not need to be used together with proxy_arp.
This technology is known by different names:
- In :rfc:`3069` it is called VLAN Aggregation
- Cisco and Allied Telesyn call it Private VLAN
- Hewlett-Packard call it Source-Port filtering or port-isolation
- Ericsson call it MAC-Forced Forwarding (RFC Draft)
.. cfgcmd:: set interfaces {{ var0 }} <interface> {{ var2 }} {{ var3 }}
{{ var5 }} {{ var6 }} ip source-validation <strict | loose | disable>
Enable policy for source validation by reversed path, as specified in
:rfc:`3704`. Current recommended practice in :rfc:`3704` is to enable strict
mode to prevent IP spoofing from DDos attacks. If using asymmetric routing
or other complicated routing, then loose mode is recommended.
- strict: Each incoming packet is tested against the FIB and if the interface
is not the best reverse path the packet check will fail. By default failed
packets are discarded.
- loose: Each incoming packet's source address is also tested against the FIB
and if the source address is not reachable via any interface the packet
check will fail.
- disable: No source validation
|
