1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
|
:lastproofread: 2023-01-20
.. _ethernet-interface:
########
Ethernet
########
This will be the most widely used interface on a router carrying traffic to the
real world.
*************
Configuration
*************
Common interface configuration
==============================
.. cmdinclude:: /_include/interface-common-with-dhcp.txt
:var0: ethernet
:var1: eth0
Ethernet options
================
.. cfgcmd:: set interfaces ethernet <interface> duplex <auto | full | half>
Configure physical interface duplex setting.
* auto - interface duplex setting is auto-negotiated
* full - always use full-duplex
* half - always use half-duplex
VyOS default will be `auto`.
.. cfgcmd:: set interfaces ethernet <interface> speed <auto | 10 | 100 | 1000 |
2500 | 5000 | 10000 | 25000 | 40000 | 50000 | 100000>
Configure physical interface speed setting.
* auto - interface speed is auto-negotiated
* 10 - 10 MBit/s
* 100 - 100 MBit/s
* 1000 - 1 GBit/s
* 2500 - 2.5 GBit/s
* 5000 - 5 GBit/s
* 10000 - 10 GBit/s
* 25000 - 25 GBit/s
* 40000 - 40 GBit/s
* 50000 - 50 GBit/s
* 100000 - 100 GBit/s
VyOS default will be `auto`.
Offloading
----------
.. cfgcmd:: set interfaces ethernet <interface> offload <gro | gso | sg | tso |
ufo | rps>
Enable different types of hardware offloading on the given NIC.
:abbr:`LRO (Large Receive Offload)` is a technique designed to boost the
efficiency of how your computer's network interface card (NIC) processes
incoming network traffic. Typically, network data arrives in smaller chunks
called packets. Processing each packet individually consumes CPU (central
processing unit) resources. Lots of small packets can lead to a performance
bottleneck. Instead of handing the CPU each packet as it comes in, LRO
instructs the NIC to combine multiple incoming packets into a single, larger
packet. This larger packet is then passed to the CPU for processing.
.. note:: Under some circumstances, LRO is known to modify the packet headers
of forwarded traffic, which breaks the end-to-end principle of computer
networking. LRO is also only able to offload TCP segments encapsulated in
IPv4 packets. Due to these limitations, it is recommended to use GRO
(Generic Receive Offload) where possible. More information on the
limitations of LRO can be found here: https://lwn.net/Articles/358910/
:abbr:`GSO (Generic Segmentation Offload)` is a pure software offload that is
meant to deal with cases where device drivers cannot perform the offloads
described above. What occurs in GSO is that a given skbuff will have its data
broken out over multiple skbuffs that have been resized to match the MSS
provided via skb_shinfo()->gso_size.
Before enabling any hardware segmentation offload a corresponding software
offload is required in GSO. Otherwise it becomes possible for a frame to be
re-routed between devices and end up being unable to be transmitted.
:abbr:`GRO (Generic receive offload)` is the complement to GSO. Ideally any
frame assembled by GRO should be segmented to create an identical sequence of
frames using GSO, and any sequence of frames segmented by GSO should be able
to be reassembled back to the original by GRO. The only exception to this is
IPv4 ID in the case that the DF bit is set for a given IP header. If the
value of the IPv4 ID is not sequentially incrementing it will be altered so
that it is when a frame assembled via GRO is segmented via GSO.
:abbr:`RPS (Receive Packet Steering)` is logically a software implementation
of :abbr:`RSS (Receive Side Scaling)`. Being in software, it is necessarily
called later in the datapath. Whereas RSS selects the queue and hence CPU that
will run the hardware interrupt handler, RPS selects the CPU to perform
protocol processing above the interrupt handler. This is accomplished by
placing the packet on the desired CPU's backlog queue and waking up the CPU
for processing. RPS has some advantages over RSS:
- it can be used with any NIC
- software filters can easily be added to hash over new protocols
- it does not increase hardware device interrupt rate, although it does
introduce inter-processor interrupts (IPIs)
.. note:: In order to use TSO/LRO with VMXNET3 adapters, the SG offloading
option must also be enabled.
Authentication (EAPoL)
----------------------
.. cmdinclude:: /_include/interface-eapol.txt
:var0: ethernet
:var1: eth0
VLAN
====
Regular VLANs (802.1q)
----------------------
.. cmdinclude:: /_include/interface-vlan-8021q.txt
:var0: ethernet
:var1: eth0
QinQ (802.1ad)
--------------
.. cmdinclude:: /_include/interface-vlan-8021ad.txt
:var0: ethernet
:var1: eth0
Port Mirror (SPAN)
==================
.. cmdinclude:: ../../_include/interface-mirror.txt
:var0: ethernet
:var1: eth1
:var2: eth3
*********
Operation
*********
.. opcmd:: show interfaces ethernet
Show brief interface information.
.. code-block:: none
vyos@vyos:~$ show interfaces ethernet
Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
Interface IP Address S/L Description
--------- ---------- --- -----------
eth0 172.18.201.10/24 u/u LAN
eth1 172.18.202.11/24 u/u WAN
eth2 - u/D
.. opcmd:: show interfaces ethernet <interface>
Show detailed information on given `<interface>`
.. code-block:: none
vyos@vyos:~$ show interfaces ethernet eth0
eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:50:44:00:f5:c9 brd ff:ff:ff:ff:ff:ff
inet6 fe80::250:44ff:fe00:f5c9/64 scope link
valid_lft forever preferred_lft forever
RX: bytes packets errors dropped overrun mcast
56735451 179841 0 0 0 142380
TX: bytes packets errors dropped carrier collisions
5601460 62595 0 0 0 0
.. stop_vyoslinter
.. opcmd:: show interfaces ethernet <interface> physical
Show information about physical `<interface>`
.. code-block:: none
vyos@vyos:~$ show interfaces ethernet eth0 physical
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 1000baseT/Full
10000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
MDI-X: Unknown
Supports Wake-on: uag
Wake-on: d
Link detected: yes
driver: vmxnet3
version: 1.4.16.0-k-NAPI
firmware-version:
expansion-rom-version:
bus-info: 0000:0b:00.0
supports-statistics: yes
supports-test: no
supports-eeprom-access: no
supports-register-dump: yes
supports-priv-flags: no
.. start_vyoslinter
.. opcmd:: show interfaces ethernet <interface> physical offload
Show available offloading functions on given `<interface>`
.. code-block:: none
vyos@vyos:~$ show interfaces ethernet eth0 physical offload
rx-checksumming on
tx-checksumming on
tx-checksum-ip-generic on
scatter-gather off
tx-scatter-gather off
tcp-segmentation-offload off
tx-tcp-segmentation off
tx-tcp-mangleid-segmentation off
tx-tcp6-segmentation off
udp-fragmentation-offload off
generic-segmentation-offload off
generic-receive-offload off
large-receive-offload off
rx-vlan-offload on
tx-vlan-offload on
ntuple-filters off
receive-hashing on
tx-gre-segmentation on
tx-gre-csum-segmentation on
tx-udp_tnl-segmentation on
tx-udp_tnl-csum-segmentation on
tx-gso-partial on
tx-nocache-copy off
rx-all off
.. opcmd:: show interfaces ethernet <interface> transceiver
Show transceiver information from plugin modules, e.g SFP+, QSFP
.. code-block:: none
vyos@vyos:~$ show interfaces ethernet eth5 transceiver
Identifier : 0x03 (SFP)
Extended identifier : 0x04 (GBIC/SFP defined by 2-wire interface ID)
Connector : 0x07 (LC)
Transceiver codes : 0x00 0x00 0x00 0x01 0x00 0x00 0x00 0x00 0x00
Transceiver type : Ethernet: 1000BASE-SX
Encoding : 0x01 (8B/10B)
BR, Nominal : 1300MBd
Rate identifier : 0x00 (unspecified)
Length (SMF,km) : 0km
Length (SMF) : 0m
Length (50um) : 550m
Length (62.5um) : 270m
Length (Copper) : 0m
Length (OM3) : 0m
Laser wavelength : 850nm
Vendor name : CISCO-FINISAR
Vendor OUI : 00:90:65
Vendor PN : FTRJ-8519-7D-CS4
Vendor rev : A
Option values : 0x00 0x1a
Option : RX_LOS implemented
Option : TX_FAULT implemented
Option : TX_DISABLE implemented
BR margin, max : 0%
BR margin, min : 0%
Vendor SN : FNS092xxxxx
Date code : 0506xx
|
