1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
|
.. _nat66:
############
NAT66(NPTv6)
############
:abbr:`NPTv6 (IPv6-to-IPv6 Network Prefix Translation)` is an address
translation technology based on IPv6 networks, used to convert an IPv6
address prefix in an IPv6 message into another IPv6 address prefix.
We call this address translation method NAT66. Devices that support the NAT66
function are called NAT66 devices, which can provide NAT66 source
and destination address translation functions.
Overview
========
Different NAT Types
-------------------
.. _source-nat66:
SNAT66
^^^^^^
:abbr:`SNPTv6 (Source IPv6-to-IPv6 Network Prefix Translation)` The conversion
function is mainly used in the following scenarios:
* A single internal network and external network. Use the NAT66 device to
connect a single internal network and public network, and the hosts in
the internal network use IPv6 address prefixes that only support
routing within the local range. When a host in the internal network
accesses the external network, the source IPv6 address prefix in
the message will be converted into a global unicast IPv6 address
prefix by the NAT66 device.
* Redundancy and load sharing. There are multiple NAT66 devices at the edge
of an IPv6 network to another IPv6 network. The path through the NAT66
device to another IPv6 network forms an equivalent route, and traffic
can be load-shared on these NAT66 devices. In this case, you
can configure the same source address translation rules on these
NAT66 devices, so that any NAT66 device can handle IPv6 traffic between
different sites.
* Multi-homed. In a multi-homed network environment, the NAT66 device
connects to an internal network and simultaneously connects to
different external networks. Address translation can be configured
on each external network side interface of the NAT66 device to
convert the same internal network address into different external
network addresses, and realize the mapping of the same internal
address to multiple external addresses.
.. _destination-nat66:
DNAT66
^^^^^^
The :abbr:`DNPTv6 (Destination IPv6-to-IPv6 Network Prefix Translation)`
destination address translation function is used in scenarios where the
server in the internal network provides services to the external network,
such as providing Web services or FTP services to the external network.
By configuring the mapping relationship between the internal server
address and the external network address on the external network
side interface of the NAT66 device, external network users can
access the internal network server through the designated
external network address.
Prefix Conversion
------------------
Source Prefix
^^^^^^^^^^^^^
Every SNAT66 rule has a translation command defined. The prefix defined
for the translation is the prefix used when the address information in
a packet is replaced.、
The :ref:`source-nat66` rule replaces the source address of the packet
and calculates the converted address using the prefix specified in the rule.
Example:
* Convert the address prefix of a single `fc01::/64` network to `fc00::/64`
* Output from `eth0` network interface
.. code-block:: none
set nat66 source rule 1 outbound-interface 'eth0'
set nat66 source rule 1 source prefix 'fc01::/64'
set nat66 source rule 1 translation address 'fc00::/64'
Destination Prefix
^^^^^^^^^^^^^^^^^^
For the :ref:`destination-nat66` rule, the destination address of
the packet isreplaced by the address calculated from the specified
address or prefix in the `translation address` command
Example:
* Convert the address prefix of a single `fc00::/64` network
to `fc01::/64`
* Input from `eth0` network interface
.. code-block:: none
set nat66 destination rule 1 inbound-interface 'eth0'
set nat66 destination rule 1 destination address 'fc00::/64'
set nat66 destination rule 1 translation address 'fc01::/64'
Configuration Examples
======================
Use the following topology to build a nat66 based isolated
network between internal and external networks (dynamic prefix is
not supported):
.. figure:: /_static/images/vyos_1_4_nat66_simple.png
:alt: VyOS NAT66 Simple Configure
R1:
.. code-block:: none
set interfaces ethernet eth0 ipv6 address autoconf
set interfaces ethernet eth1 address 'fc01::1/64'
set nat66 destination rule 1 destination address 'fc00:470:f1cd:101::/64'
set nat66 destination rule 1 inbound-interface 'eth0'
set nat66 destination rule 1 translation address 'fc01::/64'
set nat66 source rule 1 outbound-interface 'eth0'
set nat66 source rule 1 source prefix 'fc01::/64'
set nat66 source rule 1 translation address 'fc00:470:f1cd:101::/64'
R2:
.. code-block:: none
set interfaces bridge br1 address 'fc01::2/64'
set interfaces bridge br1 member interface eth0
set interfaces bridge br1 member interface eth1
set protocols static route6 ::/0 next-hop fc01::1
set service router-advert interface br1 prefix ::/0
Use the following topology to translate internal user local addresses (``fc::/7``)
to DHCPv6-PD provided prefixes from an ISP connected to a VyOS HA pair.
.. figure:: /_static/images/vyos_1_5_nat66_dhcpv6_wdummy.png
:alt: VyOS NAT66 DHCPv6 using a dummy interface
Configure both routers (a and b) for DHCPv6-PD via dummy interface:
.. code-block:: none
set interfaces dummy dum1 description 'DHCPv6-PD NPT dummy'
set interfaces bonding bond0 vif 20 dhcpv6-options pd 0 interface dum1 address '0'
set interfaces bonding bond0 vif 20 dhcpv6-options pd 1 interface dum1 address '0'
set interfaces bonding bond0 vif 20 dhcpv6-options pd 2 interface dum1 address '0'
set interfaces bonding bond0 vif 20 dhcpv6-options pd 3 interface dum1 address '0'
set interfaces bonding bond0 vif 20 dhcpv6-options rapid-commit
commit
Get the DHCPv6-PD prefixes from both routers:
.. code-block:: none
trae@cr01a-vyos# run show interfaces dummy dum1 br
Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
Interface IP Address S/L Description
--------- ---------- --- -----------
dum1 2001:db8:123:b008::/64 u/u DHCPv6-PD NPT dummy
2001:db8:123:b00a::/64
2001:db8:123:b00b::/64
2001:db8:123:b009::/64
trae@cr01b-vyos# run show int dummy dum1 brief
Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
Interface IP Address S/L Description
--------- ---------- --- -----------
dum1 2001:db8:123:b00d::/64 u/u DHCPv6-PD NPT dummy
2001:db8:123:b00c::/64
2001:db8:123:b00e::/64
2001:db8:123:b00f::/64
Configure the A-side router for NPTv6 using the prefixes above:
.. code-block:: none
set nat66 source rule 10 description 'NPT to VLAN 10'
set nat66 source rule 10 outbound-interface name 'bond0.20'
set nat66 source rule 10 source prefix 'fd52:d62e:8011:a::/64'
set nat66 source rule 10 translation address '2001:db8:123:b008::/64'
set nat66 source rule 20 description 'NPT to VLAN 70'
set nat66 source rule 20 outbound-interface name 'bond0.20'
set nat66 source rule 20 source prefix 'fd52:d62e:8011:46::/64'
set nat66 source rule 20 translation address '2001:db8:123:b009::/64'
set nat66 source rule 30 description 'NPT to VLAN 200'
set nat66 source rule 30 outbound-interface name 'bond0.20'
set nat66 source rule 30 source prefix 'fd52:d62e:8011:c8::/64'
set nat66 source rule 30 translation address '2001:db8:123:b00a::/64'
set nat66 source rule 40 description 'NPT to VLAN 240'
set nat66 source rule 40 outbound-interface name 'bond0.20'
set nat66 source rule 40 source prefix 'fd52:d62e:8011:f0::/64'
set nat66 source rule 40 translation address '2001:db8:123:b00b::/64'
commit
Configure the B-side router for NPTv6 using the prefixes above:
.. code-block:: none
set nat66 source rule 10 description 'NPT to VLAN 10'
set nat66 source rule 10 outbound-interface name 'bond0.20'
set nat66 source rule 10 source prefix 'fd52:d62e:8011:a::/64'
set nat66 source rule 10 translation address '2001:db8:123:b00c::/64'
set nat66 source rule 20 description 'NPT to VLAN 70'
set nat66 source rule 20 outbound-interface name 'bond0.20'
set nat66 source rule 20 source prefix 'fd52:d62e:8011:46::/64'
set nat66 source rule 20 translation address '2001:db8:123:b00d::/64'
set nat66 source rule 30 description 'NPT to VLAN 200'
set nat66 source rule 30 outbound-interface name 'bond0.20'
set nat66 source rule 30 source prefix 'fd52:d62e:8011:c8::/64'
set nat66 source rule 30 translation address '2001:db8:123:b00e::/64'
set nat66 source rule 40 description 'NPT to VLAN 240'
set nat66 source rule 40 outbound-interface name 'bond0.20'
set nat66 source rule 40 source prefix 'fd52:d62e:8011:f0::/64'
set nat66 source rule 40 translation address '2001:db8:123:b00f::/64'
commit
Verify that connections are hitting the rule on both sides:
.. code-block:: none
trae@cr01a-vyos# run show nat66 source statistics
Rule Packets Bytes Interface
------ --------- ------- -----------
10 1 104 bond0.20
20 1 104 bond0.20
30 8093 669445 bond0.20
40 2446 216912 bond0.20
|
