blob: a4188c682dbdbd58d56a456d445c2969c8b0d283 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
|
.. include:: /_include/need_improvement.txt
.. _routing-ospf:
####
OSPF
####
:abbr:`OSPF (Open Shortest Path First)` is a routing protocol for Internet
Protocol (IP) networks. It uses a link state routing (LSR) algorithm and falls
into the group of interior gateway protocols (IGPs), operating within a single
autonomous system (AS). It is defined as OSPF Version 2 in :rfc:`2328` (1998)
for IPv4. Updates for IPv6 are specified as OSPF Version 3 in :rfc:`5340`
(2008). OSPF supports the :abbr:`CIDR (Classless Inter-Domain Routing)`
addressing model.
OSPF is a widely used IGP in large enterprise networks.
OSPFv2 (IPv4)
#############
In order to have a VyOS system exchanging routes with OSPF neighbors, you will
at least need to configure an OSPF area and some network.
.. code-block:: none
set protocols ospf area 0 network 192.168.0.0/24
That is the minimum configuration you will need.
It is a good practice to define the router ID too.
.. code-block:: none
set protocols ospf parameters router-id 10.1.1.1
Below you can see a typical configuration using 2 nodes, redistribute loopback
address and the node 1 sending the default route:
**Node 1**
.. code-block:: none
set interfaces loopback lo address 10.1.1.1/32
set protocols ospf area 0 network 192.168.0.0/24
set protocols ospf default-information originate always
set protocols ospf default-information originate metric 10
set protocols ospf default-information originate metric-type 2
set protocols ospf log-adjacency-changes
set protocols ospf parameters router-id 10.1.1.1
set protocols ospf redistribute connected metric-type 2
set protocols ospf redistribute connected route-map CONNECT
set policy route-map CONNECT rule 10 action permit
set policy route-map CONNECT rule 10 match interface lo
**Node 2**
.. code-block:: none
set interfaces loopback lo address 10.2.2.2/32
set protocols ospf area 0 network 192.168.0.0/24
set protocols ospf log-adjacency-changes
set protocols ospf parameters router-id 10.2.2.2
set protocols ospf redistribute connected metric-type 2
set protocols ospf redistribute connected route-map CONNECT
set policy route-map CONNECT rule 10 action permit
set policy route-map CONNECT rule 10 match interface lo
OSPFv3 (IPv6)
#############
A typical configuration using 2 nodes.
**Node 1:**
.. code-block:: none
set protocols ospfv3 area 0.0.0.0 interface eth1
set protocols ospfv3 area 0.0.0.0 range 2001:db8:1::/64
set protocols ospfv3 parameters router-id 192.168.1.1
set protocols ospfv3 redistribute connected
**Node 2:**
.. code-block:: none
set protocols ospfv3 area 0.0.0.0 interface eth1
set protocols ospfv3 area 0.0.0.0 range 2001:db8:2::/64
set protocols ospfv3 parameters router-id 192.168.2.1
set protocols ospfv3 redistribute connected
**To see the redistributed routes:**
.. code-block:: none
show ipv6 ospfv3 redistribute
.. note:: You cannot easily redistribute IPv6 routes via OSPFv3 on a WireGuard
interface link. This requires you to configure link-local addresses manually
on the WireGuard interfaces, see :vytask:`T1483`.
Example configuration for WireGuard interfaces:
**Node 1**
.. code-block:: none
set interfaces wireguard wg01 address 'fe80::216:3eff:fe51:fd8c/64'
set interfaces wireguard wg01 address '192.168.0.1/24'
set interfaces wireguard wg01 peer ospf02 allowed-ips '::/0'
set interfaces wireguard wg01 peer ospf02 allowed-ips '0.0.0.0/0'
set interfaces wireguard wg01 peer ospf02 endpoint '10.1.1.101:12345'
set interfaces wireguard wg01 peer ospf02 pubkey 'ie3...='
set interfaces wireguard wg01 port '12345'
set protocols ospfv3 parameters router-id 192.168.1.1
set protocols ospfv3 area 0.0.0.0 interface 'wg01'
set protocols ospfv3 area 0.0.0.0 interface 'lo'
**Node 2**
.. code-block:: none
set interfaces wireguard wg01 address 'fe80::216:3eff:fe0a:7ada/64'
set interfaces wireguard wg01 address '192.168.0.2/24'
set interfaces wireguard wg01 peer ospf01 allowed-ips '::/0'
set interfaces wireguard wg01 peer ospf01 allowed-ips '0.0.0.0/0'
set interfaces wireguard wg01 peer ospf01 endpoint '10.1.1.100:12345'
set interfaces wireguard wg01 peer ospf01 pubkey 'NHI...='
set interfaces wireguard wg01 port '12345'
set protocols ospfv3 parameters router-id 192.168.1.2
set protocols ospfv3 area 0.0.0.0 interface 'wg01'
set protocols ospfv3 area 0.0.0.0 interface 'lo'
**Status**
.. code-block:: none
vyos@ospf01:~$ sh ipv6 ospfv3 neighbor
Neighbor ID Pri DeadTime State/IfState Duration I/F[State]
192.168.0.2 1 00:00:37 Full/PointToPoint 00:18:03 wg01[PointToPoint]
vyos@ospf02# run sh ipv6 ospfv3 neighbor
Neighbor ID Pri DeadTime State/IfState Duration I/F[State]
192.168.0.1 1 00:00:39 Full/PointToPoint 00:19:44 wg01[PointToPoint]
|
