1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
|
.. _ethernet-interface:
########
Ethernet
########
Configuration
#############
Common interface configuration
------------------------------
.. cmdinclude:: ../_include/interface-address-with-dhcp.txt
:var0: ethernet
:var1: eth0
.. cmdinclude:: ../_include/interface-description.txt
:var0: ethernet
:var1: eth0
.. cmdinclude:: ../_include/interface-ipv6-addr-autoconf.txt
:var0: ethernet
:var1: eth0
.. cmdinclude:: ../_include/interface-ipv6-addr-eui64.txt
:var0: ethernet
:var1: eth0
Speed/Duplex
------------
.. cfgcmd:: set interfaces ethernet <interface> duplex <auto | full | half>
Configure physical interface duplex setting.
* auto - interface duplex setting is auto-negotiated
* full - always use full-duplex
* half - always use half-duplex
VyOS default will be `auto`.
.. cfgcmd:: set interfaces ethernet <interface> speed <auto | 10 | 100 | 1000 | 2500 | 5000 | 10000 | 25000 | 40000 | 50000 | 100000>
Configure physical interface speed setting.
* auto - interface speed is auto-negotiated
* 10 - 10 MBit/s
* 100 - 100 MBit/s
* 1000 - 1 GBit/s
* 2500 - 2.5 GBit/s
* 5000 - 5 GBit/s
* 10000 - 10 GBit/s
* 25000 - 25 GBit/s
* 40000 - 40 GBit/s
* 50000 - 50 GBit/s
* 100000 - 100 GBit/s
VyOS default will be `auto`.
Link Administration
-------------------
.. cfgcmd:: set interfaces ethernet <interface> description <description>
Assign given `<description>` to interface. Description will also be passed
to SNMP monitoring systems.
.. cfgcmd:: set interfaces ethernet <interface> disable
Disable given `<interface>`. It will be placed in administratively down
(``A/D``) state.
.. cfgcmd:: set interfaces ethernet <interface> disable-flow-control
Disable Ethernet flow control (pause frames).
.. cfgcmd:: set interfaces ethernet <interface> mac <mac-address>
Configure user defined :abbr:`MAC (Media Access Control)` address on given
`<interface>`.
.. cfgcmd:: set interfaces ethernet <interface> mtu <mtu>
Configure :abbr:`MTU (Maximum Transmission Unit)` on given `<interface>`. It
is the size (in bytes) of the largest ethernet frame sent on this link.
Prefix Delegation (DHCPv6-PD)
-----------------------------
VyOS 1.3 (equuleus) supports DHCPv6-PD. DHCPv6 Prefix Delegation is supported
by most ISPs who provide native IPv6 for consumers on fixed networks.
.. cfgcmd:: set interfaces ethernet <interface> dhcpv6-option pd <id> length <length>
Some ISPs by default only delegate a /64 prefix. To request for a specific
prefix size use this option to request for a bigger delegation for this pd
`<id>`. This value
is in the range from 32 - 64 so you could request up to /32 down to a /64
delegation.
Default value is 64.
.. cfgcmd:: set interfaces ethernet <interface> dhcpv6-option pd <id> interface <delegatee> address <address>
Specify the interface address used locally on the interfcae where the prefix
has been delegated to. ID must be a decimal integer.
It will be combined with the delegated prefix and the sla-id to form a complete
interface address. The default is to use the EUI-64 address of the interface.
Example:
Using ``<id>`` value 65535 will assign IPv6 address ``<prefix>::ffff`` to the
interface.
.. cfgcmd:: set interfaces ethernet <interface> dhcpv6-option pd <id> interface <delegatee> sla-id <id>
Specify the identifier value of the site-level aggregator (SLA) on the
interface. ID must be a decimal number greater then 0 which fits in the length
of SLA IDs (see below). For example, if ID is 1 and the client is delegated
an IPv6 prefix 2001:db8:ffff::/48, dhcp6c will combine the two values into a
single IPv6 prefix, 2001:db8:ffff:1::/64, and will configure the prefix on
the specified interface.
Operation
=========
.. opcmd:: show interfaces ethernet
Show brief interface information.
.. code-block:: none
vyos@vyos:~$ show interfaces ethernet
Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
Interface IP Address S/L Description
--------- ---------- --- -----------
eth0 172.18.201.10/24 u/u LAN
eth1 172.18.202.11/24 u/u WAN
eth2 - u/D
.. opcmd:: show interfaces ethernet <interface>
Show detailed information on given `<interface>`
.. code-block:: none
vyos@vyos:~$ show interfaces ethernet eth0
eth0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP group default qlen 1000
link/ether 00:50:44:00:f5:c9 brd ff:ff:ff:ff:ff:ff
inet6 fe80::250:44ff:fe00:f5c9/64 scope link
valid_lft forever preferred_lft forever
RX: bytes packets errors dropped overrun mcast
56735451 179841 0 0 0 142380
TX: bytes packets errors dropped carrier collisions
5601460 62595 0 0 0 0
.. opcmd:: show interfaces ethernet <interface> physical
Show information about physical `<interface>`
.. code-block:: none
vyos@vyos:~$ show interfaces ethernet eth0 physical
Settings for eth0:
Supported ports: [ TP ]
Supported link modes: 1000baseT/Full
10000baseT/Full
Supported pause frame use: No
Supports auto-negotiation: No
Supported FEC modes: Not reported
Advertised link modes: Not reported
Advertised pause frame use: No
Advertised auto-negotiation: No
Advertised FEC modes: Not reported
Speed: 10000Mb/s
Duplex: Full
Port: Twisted Pair
PHYAD: 0
Transceiver: internal
Auto-negotiation: off
MDI-X: Unknown
Supports Wake-on: uag
Wake-on: d
Link detected: yes
driver: vmxnet3
version: 1.4.16.0-k-NAPI
firmware-version:
expansion-rom-version:
bus-info: 0000:0b:00.0
supports-statistics: yes
supports-test: no
supports-eeprom-access: no
supports-register-dump: yes
supports-priv-flags: no
.. opcmd:: show interfaces ethernet <interface> physical offload
Show available offloading functions on given `<interface>`
.. code-block:: none
vyos@vyos:~$ show interfaces ethernet eth0 physical offload
rx-checksumming on
tx-checksumming on
tx-checksum-ip-generic on
scatter-gather off
tx-scatter-gather off
tcp-segmentation-offload off
tx-tcp-segmentation off
tx-tcp-mangleid-segmentation off
tx-tcp6-segmentation off
udp-fragmentation-offload off
generic-segmentation-offload off
generic-receive-offload off
large-receive-offload off
rx-vlan-offload on
tx-vlan-offload on
ntuple-filters off
receive-hashing on
tx-gre-segmentation on
tx-gre-csum-segmentation on
tx-udp_tnl-segmentation on
tx-udp_tnl-csum-segmentation on
tx-gso-partial on
tx-nocache-copy off
rx-all off
.. opcmd:: show interfaces ethernet <interface> transceiver
Show transceiver information from plugin modules, e.g SFP+, QSFP
.. code-block:: none
vyos@vyos:~$ show interfaces ethernet eth5 transceiver
Identifier : 0x03 (SFP)
Extended identifier : 0x04 (GBIC/SFP defined by 2-wire interface ID)
Connector : 0x07 (LC)
Transceiver codes : 0x00 0x00 0x00 0x01 0x00 0x00 0x00 0x00 0x00
Transceiver type : Ethernet: 1000BASE-SX
Encoding : 0x01 (8B/10B)
BR, Nominal : 1300MBd
Rate identifier : 0x00 (unspecified)
Length (SMF,km) : 0km
Length (SMF) : 0m
Length (50um) : 550m
Length (62.5um) : 270m
Length (Copper) : 0m
Length (OM3) : 0m
Laser wavelength : 850nm
Vendor name : CISCO-FINISAR
Vendor OUI : 00:90:65
Vendor PN : FTRJ-8519-7D-CS4
Vendor rev : A
Option values : 0x00 0x1a
Option : RX_LOS implemented
Option : TX_FAULT implemented
Option : TX_DISABLE implemented
BR margin, max : 0%
BR margin, min : 0%
Vendor SN : FNS092xxxxx
Date code : 0506xx
|
