1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
|
.. _wireless:
Wireless Interfaces
-------------------
:abbr:`WLAN (Wireless LAN)` interface provide 802.11 (a/b/g/n/ac) wireless
support (commonly referred to as Wi-Fi) by means of compatible hardware. If your
hardware supports it, VyOS supports multiple logical wireless interfaces per
physical device.
There are three modes of operation for a wireless interface:
* :abbr:`WAP (Wireless Access-Point)` provides network access to connecting
stations if the physical hardware supports acting as a WAP
* A station acts as a Wi-Fi client accessing the network through an available
WAP
* Monitor, the system passively monitors any kind of wireless traffic
If the system detects an unconfigured wireless device, it will be automatically
added the configuration tree, specifying any detected settings (for example,
its MAC address) and configured to run in monitor mode.
To be able to use the wireless interfaces you will first need to set a
regulatory domain with the country code of your locaion.
.. option:: set system wifi-regulatory-domain DE
Configure system wide Wi-Fi regulatory domain. A reboot is required for this
change to be enabled.
Configuring Access-Point
^^^^^^^^^^^^^^^^^^^^^^^^
The following example creates a WAP. When configuring multiple WAP interfaces,
you must specify unique IP addresses, channels, Network IDs commonly refered
to as :addr:`SSID (Service Set Identifier), and MAC addresses.
The WAP in this example has the following characteristics:
* IP address ``192.0.2.1/24``
* Network ID (SSID) ``TEST``
* WPA passphrase ``12345678``
* Use 802.11n protocol
* Wireless channel ``1``
.. code-block:: sh
set interfaces wireless wlan0 address '192.0.2.1/24'
set interfaces wireless wlan0 type access-point
set interfaces wireless wlan0 channel 1
set interfaces wireless wlan0 mode n
set interfaces wireless wlan0 ssid 'TEST'
set interfaces wireless wlan0 security wpa mode wpa2
set interfaces wireless wlan0 security wpa cipher CCMP
set interfaces wireless wlan0 security wpa passphrase '12345678'
Resulting in
.. code-block:: sh
interfaces {
[...]
wireless wlan0 {
address 192.0.2.1/24
channel 1
mode n
security {
wpa {
cipher CCMP
mode wpa2
passphrase "12345678"
}
}
ssid "TEST"
type access-point
}
}
system {
[...]
wifi-regulatory-domain DE
}
To get it to work as a access point with this configuration you will need
to set up a DHCP server to work with that network. You can - of course - also
bridge the Wireless interface with any configured bridge (:ref:`bridge`) on
the system.
Configuring Wireless Station
^^^^^^^^^^^^^^^^^^^^^^^^^^^^
The example creates a wireless station (commonly referred to as Wi-Fi client)
that accesses the network through the WAP defined in the above example. The
default physical device (``phy0``) is used.
.. code-block:: sh
set interfaces wireless wlan0 type station
set interfaces wireless wlan0 address dhcp
set interfaces wireless wlan0 ssid Test
set interfaces wireless wlan0 security wpa
Resulting in
.. code-block:: sh
interfaces {
[...]
wireless wlan0 {
address dhcp
security {
wpa {
passphrase "12345678"
}
}
ssid TEST
type station
}
Operational Commands
^^^^^^^^^^^^^^^^^^^^
.. option:: show interfaces wireless info
Use this command to view operational status and wireless-specific information
about all wireless interfaces.
.. code-block:: sh
vyos@vyos:~$ show interfaces wireless info
Interface Type SSID Channel
mon.wlan0 monitor ? ?
wlan0 AP testing 3
.. option:: show interfaces wireless detail
Use this command to view operational status and detailes wireless-specific
information about all wireless interfaces.
.. code-block:: sh
vyos@vyos:~$ show interfaces wireless detail
wlan0: <NO?CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc pfifo_fast state DOWN0
link/ether 00:21:91:d1:18:ca brd ff:ff:ff:ff:ff:ff
RX: bytes packets errors dropped overrun mcast
0 0 0 0 0 0
TX: bytes packets errors dropped carrier collisions
0 0 0 0 0 0
|
