path: root/docs/troubleshooting/index.rst

.. _troubleshooting:

###############
Troubleshooting
###############

Sometimes things break or don't work as expected. This section describes
several troubleshooting tools provided by VyOS that can help when something
goes wrong.

******************
Connectivity Tests
******************

Basic Connectivity Tests
========================

Verifying connectivity can be done with the familiar `ping` and `traceroute`
commands. The options for each are shown (the options for each command were
displayed using the built-in help as described in the :ref:`cli`
section and are omitted from the output here):

.. opcmd:: ping <destination>

   Send ICMP echo requests to destination host. There are multiple options to
   ping.

   .. code-block:: none

     vyos@vyos:~$ ping 10.1.1.1
     Possible completions:
       <Enter>       Execute the current command
       adaptive      Ping options
       allow-broadcast
       audible
       bypass-route
       count
       deadline
       flood
       interface
       interval
       mark
       no-loopback
       numeric
       pattern
       quiet
       record-route
       size
       timestamp
       tos
       ttl
       verbose


.. opcmd:: traceroute <destination>

   Trace path to target.

   .. code-block:: none

     vyos@vyos:~$ traceroute
     Possible completions:
       <hostname>    Track network path to specified node
       <x.x.x.x>
       <h:h:h:h:h:h:h:h>
       ipv4          Track network path to <hostname|IPv4 address>
       ipv6          Track network path to <hostname|IPv6 address>


Advanced Connectivity Tests
===========================

.. opcmd:: monitor traceroute <destination>

   However, another helper is available which combines ping and traceroute
   into a single tool. An example of its output is shown:

   .. code-block:: none

     vyos@vyos:~$ mtr 10.62.212.12

                                My traceroute  [v0.85]
     vyos (0.0.0.0)
     Keys:  Help   Display mode   Restart statistics   Order of fields   quit
                                       Packets               Pings
     Host                            Loss%   Snt   Last   Avg  Best  Wrst StDev
     1. 10.11.110.4                   0.0%    34    0.5   0.5   0.4   0.8   0.1
     2. 10.62.255.184                 0.0%    34    1.1   1.0   0.9   1.4   0.1
     3. 10.62.255.71                  0.0%    34    1.4   1.4   1.3   2.0   0.1
     4. 10.62.212.12                  0.0%    34    1.6   1.6   1.6   1.7   0.0

   .. note:: The output consumes the screen and will replace your command
      prompt.

   Several options are available for changing the display output. Press `h` to
   invoke the built in help system. To quit, just press `q` and you'll be
   returned to the VyOS command prompt.

IPv6 Topology Discovery
=======================

IPv6 uses different techniques to discover its Neighbors/topology.

Router Discovery
----------------

.. opcmd:: force ipv6-rd interface <interface> [address <ipv6-address>]

   Discover routers via eth0.

   Example:

   .. code-block:: none

     vyos@vyos:~$ force ipv6-rd interface eth0
     Soliciting ff02::2 (ff02::2) on eth0...

     Hop limit                 :           60 (      0x3c)
     Stateful address conf.    :           No
     Stateful other conf.      :           No
     Mobile home agent         :           No
     Router preference         :         high
     Neighbor discovery proxy  :           No
     Router lifetime           :         1800 (0x00000708) seconds
     Reachable time            :  unspecified (0x00000000)
     Retransmit time           :  unspecified (0x00000000)
      Prefix                   : 240e:fe:8ca7:ea01::/64
       On-link                 :          Yes
       Autonomous address conf.:          Yes
       Valid time              :      2592000 (0x00278d00) seconds
       Pref. time              :        14400 (0x00003840) seconds
      Prefix                   : fc00:470:f1cd:101::/64
       On-link                 :          Yes
       Autonomous address conf.:          Yes
       Valid time              :      2592000 (0x00278d00) seconds
       Pref. time              :        14400 (0x00003840) seconds
      Recursive DNS server     : fc00:470:f1cd::ff00
       DNS server lifetime     :          600 (0x00000258) seconds
      Source link-layer address: 00:98:2B:F8:3F:11
      from fe80::298:2bff:fef8:3f11

Neighbor Discovery
------------------

.. opcmd:: force ipv6-nd interface <interface> address <ipv6-address>


   Example:

   .. code-block:: none

     vyos@vyos:~$ force ipv6-nd interface eth0 address fc00:470:f1cd:101::1

     Soliciting fc00:470:f1cd:101::1 (fc00:470:f1cd:101::1) on eth0...
     Target link-layer address: 00:98:2B:F8:3F:11 from fc00:470:f1cd:101::1


***************
Interface names
***************

If you find the names of your interfaces have changed, this could be because
your MAC addresses have changed.

* For example, you have a VyOS VM with 4 Ethernet interfaces named
  eth0, eth1, eth2 and eth3. Then, you migrate your VyOS VM to a different
  host and find your interfaces now are eth4, eth5, eth6 and eth7.

  One way to fix this issue **taking control of the MAC addresses** is:

  Log into VyOS and run this command to display your interface settings.

  .. code-block:: none

     show interfaces detail

  Take note of MAC addresses.

  Now, in order to update a MAC address in the configuration, run this command
  specifying the interface name and MAC address you want.

  .. code-block:: none

     set interfaces eth0 hw-id 00:0c:29:da:a4:fe

  If it is a VM, go into the settings of the host and set the MAC address to
  the settings found in the config.boot file. You can also set the MAC to
  static if the host allows so.


* Another example could be when cloning VyOS VMs in GNS3 and you get into the
  same issue: interface names have changed.
  
  And **a more generic way to fix it** is just deleting every MAC address at
  the configuration file of the cloned machine. They will be correctly
  regenerated automatically.


**********
Monitoring
**********

VyOS features several monitoring tools.

.. code-block:: none

  vyos@vyos:~$ monitor
  Possible completions:
    bandwidth     Monitor interface bandwidth in real time
    bandwidth-test
                  Initiate or wait for bandwidth test
    cluster       Monitor clustering service
    command       Monitor an operational mode command (refreshes every 2 seconds)
    conntrack-sync
                  Monitor conntrack-sync
    content-inspection
                  Monitor Content-Inspection
    dhcp          Monitor Dynamic Host Control Protocol (DHCP)
    dns           Monitor a Domain Name Service (DNS) daemon
    firewall      Monitor Firewall
    https         Monitor the Secure Hypertext Transfer Protocol (HTTPS) service
    lldp          Monitor Link Layer Discovery Protocol (LLDP) daemon
    log           Monitor last lines of messages file
    nat           Monitor network address translation (NAT)
    ndp           Monitor the NDP information received by the router through the device
    openvpn       Monitor OpenVPN
    protocol      Monitor routing protocols
    snmp          Monitor Simple Network Management Protocol (SNMP) daemon
    stop-all      Stop all current background monitoring processes
    traceroute    Monitor the path to a destination in realtime
    traffic       Monitor traffic dumps
    vpn           Monitor VPN
    vrrp          Monitor Virtual Router Redundancy Protocol (VRRP)
    webproxy      Monitor Webproxy service


Traffic Dumps
=============

To monitor interface traffic, issue the :code:`monitor traffic interface <name>`
command, replacing `<name>` with your chosen interface.

.. code-block:: none

  vyos@vyos:~$ monitor traffic interface eth0
  tcpdump: verbose output suppressed, use -v or -vv for full protocol decode
  listening on eth0, link-type EN10MB (Ethernet), capture size 262144 bytes
  15:54:28.581601 IP 192.168.0.1 > vyos: ICMP echo request, id 1870, seq 3848, length 64
  15:54:28.581660 IP vyos > 192.168.0.1: ICMP echo reply, id 1870, seq 3848, length 64
  15:54:29.583399 IP 192.168.0.1 > vyos: ICMP echo request, id 1870, seq 3849, length 64
  15:54:29.583454 IP vyos > 192.168.0.1: ICMP echo reply, id 1870, seq 3849, length 64
  ^C
  4 packets captured
  4 packets received by filter
  0 packets dropped by kernel
  vyos@vyos:~$

To quit monitoring, press `Ctrl-c` and you'll be returned to the VyOS command
prompt.

Traffic can be filtered and saved.

.. code-block:: none

  vyos@vyos:~$ monitor traffic interface eth0
  Possible completions:
    <Enter>       Execute the current command
    filter        Monitor traffic matching filter conditions
    save          Save traffic dump from an interface to a file


Interface Bandwidth Usage
=========================

to take a quick view on the used bandwidth of an interface use the ``monitor
bandwidth`` command

.. code-block:: none

  vyos@vyos:~$ monitor bandwidth interface eth0

show the following:

.. code-block:: none

         B                      (RX Bytes/second)
    198.00 .|....|.....................................................
    165.00 .|....|.....................................................
    132.00 ||..|.|.....................................................
     99.00 ||..|.|.....................................................
     66.00 |||||||.....................................................
     33.00 |||||||.....................................................
           1   5   10   15   20   25   30   35   40   45   50   55   60

       KiB                      (TX Bytes/second)
      3.67 ......|.....................................................
      3.06 ......|.....................................................
      2.45 ......|.....................................................
      1.84 ......|.....................................................
      1.22 ......|.....................................................
      0.61 :::::||.....................................................
           1   5   10   15   20   25   30   35   40   45   50   55   60

Interface Performance
=====================

To take a look on the network bandwidth between two nodes, the ``monitor
bandwidth-test`` command is used to run iperf.

.. code-block:: none

  vyos@vyos:~$ monitor bandwidth-test
  Possible completions:
    accept        Wait for bandwidth test connections (port TCP/5001)
    initiate      Initiate a bandwidth test

* The ``accept`` command opens a listening iperf server on TCP Port 5001
* The ``initiate`` command connects to that server to perform the test.

.. code-block:: none

  vyos@vyos:~$ monitor bandwidth-test initiate
  Possible completions:
    <hostname>    Initiate a bandwidth test to specified host (port TCP/5001)
    <x.x.x.x>
    <h:h:h:h:h:h:h:h>


Monitor command
===============

The ``monitor command`` command allows you to repeatedly run a command to view
a continuously refreshed output. The command is run and output every 2 seconds,
allowing you to monitor the output continuously without having to re-run the
command. This can be useful to follow routing adjacency formation.

.. code-block:: none

  vyos@router:~$ monitor command "show interfaces"

Will clear the screen and show you the output of ``show interfaces`` every
2 seconds.

.. code-block:: none

  Every 2.0s: /opt/vyatta/bin/vyatta-op-cmd-wrapper    Sun Mar 26 02:49:46 2019

  Codes: S - State, L - Link, u - Up, D - Down, A - Admin Down
  Interface        IP Address                        S/L  Description
  ---------        ----------                        ---  -----------
  eth0             192.168.1.1/24                    u/u
  eth0.5           198.51.100.4/24                   u/u  WAN
  lo               127.0.0.1/8                       u/u
                   ::1/128
  vti0             172.25.254.2/30                   u/u
  vti1             172.25.254.9/30                   u/u

****************
Terminal/Console
****************

Sometimes you need to clear counters or statistics to troubleshoot better.

To do this use the ``clear`` command in Operational mode.

to clear the console output

.. code-block:: none

  vyos@vyos:~$ clear console

to clear interface counters

.. code-block:: none

  # clear all interfaces
  vyos@vyos:~$ clear interface ethernet counters
  # clear specific interface
  vyos@vyos:~$ clear interface ehternet eth0 counters

The command follow the same logic as the ``set`` command in configuration mode.

.. code-block:: none

  # clear all counters of a interface type
  vyos@vyos:~$ clear interface <interface_type> counters
  # clear counter of a interface in interface_type
  vyos@vyos:~$ clear interface <interface_type> <interace_name> counters


to clear counters on firewall rulesets or single rules

.. code-block:: none

  vyos@vyos:~$ clear firewall name <ipv4 ruleset name> counters
  vyos@vyos:~$ clear firewall name <ipv4 ruleset name> rule <rule#> counters

  vyos@vyos:~$ clear firewall ipv6-name <ipv6 ruleset name> counters
  vyos@vyos:~$ clear firewall ipv6-name <ipv6 ruleset name> rule <rule#> counters


******************
System Information
******************

.. _boot-steps:

Boot Steps
==========

VyOS 1.2 uses `Debian Jessie`_ as the base Linux operating system. Jessie was
the first version of Debian that uses systemd_ as the default init system.

These are the boot steps for VyOS 1.2

1. The BIOS loads Grub (or isolinux for the Live CD)
2. Grub then starts the Linux boot and loads the Linux Kernel ``/boot/vmlinuz``
3. Kernel Launches Systemd ``/lib/systemd/systemd``
4. Systemd loads the VyOS service file
   ``/lib/systemd/system/vyos-router.service``
5. The service file launches the VyOS router init script
   ``/usr/libexec/vyos/init/vyos-router`` - this is part of the vyatta-cfg_
   Debian package

  1. Starts FRR_ - successor to `GNU Zebra`_ and Quagga_

  2. Initialises the boot configuration file - copies over
     ``config.boot.default`` if there is no configuration
  3. Runs the configuration migration, if the configuration is for an older
     version of VyOS
  4. Runs The pre-config script, if there is one
     ``/config/scripts/vyos-preconfig-bootup.script``
  5. If the config file was upgraded, runs any post upgrade scripts
     ``/config/scripts/post-upgrade.d``
  6. Starts ``rl-system`` and ``firewall``
  7. Mounts the ``/boot`` partition
  8. The boot configuration file is then applied by ``/opt/vyatta/sbin/
     vyatta-boot-config-loader/opt/vyatta/etc/config/config.boot``

    1. The config loader script writes log entries to
       ``/var/log/vyatta-config-loader.log``

  10. Runs ``telinit q`` to tell the init system to reload ``/etc/inittab``
  11. Finally it runs the post-config script
      ``/config/scripts/vyos-postconfig-bootup.script``

.. stop_vyoslinter

.. _Quagga: https://www.quagga.net/
.. _`GNU Zebra`: https://www.gnu.org/software/zebra/
.. _FRR: https://frrouting.org/
.. _vyatta-cfg: https://github.com/vyos/vyatta-cfg
.. _systemd: https://freedesktop.org/wiki/Software/systemd/
.. _`Debian Jessie`: https://www.debian.org/releases/jessie/
.. _tshark: https://www.wireshark.org/docs/man-pages/tshark.html
.. _`PCAP filter expressions`: http://www.tcpdump.org/manpages/pcap-filter.7.html

.. start_vyoslinter