1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
252
253
254
255
256
257
258
259
260
261
262
263
264
265
266
267
268
269
270
271
272
273
274
275
276
277
278
279
280
281
282
283
284
285
286
287
288
289
290
291
292
293
294
295
296
297
298
299
300
301
302
303
304
305
306
307
308
309
310
311
312
313
314
315
316
317
318
319
320
321
322
323
324
325
326
327
328
329
330
331
332
333
334
335
|
.. _vpn-dmvpn:
#####
DMVPN
#####
:abbr:`DMVPN (Dynamic Multipoint Virtual Private Network)` is a dynamic
:abbr:`VPN (Virtual Private Network)` technology originally developed by Cisco.
While their implementation was somewhat proprietary, the underlying
technologies are actually standards based. The three technologies are:
* :abbr:`NHRP (Next Hop Resolution Protocol)` :rfc:`2332`
* :abbr:`mGRE (Multipoint Generic Routing Encapsulation)` :rfc:`1702`
* :abbr:`IPSec (IP Security)` - too many RFCs to list, but start with :rfc:`4301`
NHRP provides the dynamic tunnel endpoint discovery mechanism (endpoint
registration, and endpoint discovery/lookup), mGRE provides the tunnel
encapsulation itself, and the IPSec protocols handle the key exchange, and
crypto mechanism.
In short, DMVPN provides the capability for creating a dynamic-mesh VPN
network without having to pre-configure (static) all possible tunnel end-point
peers.
.. note:: DMVPN only automates the tunnel endpoint discovery and setup. A
complete solution also incorporates the use of a routing protocol. BGP is
particularly well suited for use with DMVPN.
.. figure:: ../_static/images/vpn_dmvpn_topology01.png
:scale: 40 %
:alt: Baseline DMVPN topology
Baseline DMVPN topology
*************
Configuration
*************
* Please refer to the :ref:`tunnel-interface` documentation for the individual
tunnel related options.
* Please refer to the :ref:`ipsec` documentation for the individual IPSec
related options.
.. cfgcmd:: set protocols nhrp tunnel <tunnel> cisco-authentication <secret>
Enables Cisco style authentication on NHRP packets. This embeds the secret
plaintext password to the outgoing NHRP packets. Incoming NHRP packets on
this interface are discarded unless the secret password is present. Maximum
length of the secret is 8 characters.
.. cfgcmd:: set protocols nhrp tunnel <tunnel> dynamic-map <address>
nbma-domain-name <fqdn>
Specifies that the :abbr:`NBMA (Non-broadcast multiple-access network)`
addresses of the next hop servers are defined in the domain name
nbma-domain-name. For each A record opennhrp creates a dynamic NHS entry.
Each dynamic NHS will get a peer entry with the configured network address
and the discovered NBMA address.
The first registration request is sent to the protocol broadcast address, and
the server's real protocol address is dynamically detected from the first
registration reply.
.. cfgcmd:: set protocols nhrp tunnel <tunnel> holding-time <timeout>
Specifies the holding time for NHRP Registration Requests and Resolution
Replies sent from this interface or shortcut-target. The holdtime is specified
in seconds and defaults to two hours.
.. cfgcmd:: set protocols nhrp tunnel <tunnel> map cisco
If the statically mapped peer is running Cisco IOS, specify the cisco keyword.
It is used to fix statically the Registration Request ID so that a matching
Purge Request can be sent if NBMA address has changed. This is to work around
broken IOS which requires Purge Request ID to match the original Registration
Request ID.
.. cfgcmd:: set protocols nhrp tunnel <tunnel> map nbma-address <address>
Creates static peer mapping of protocol-address to :abbr:`NBMA (Non-broadcast
multiple-access network)` address.
If the IP prefix mask is present, it directs opennhrp to use this peer as a
next hop server when sending Resolution Requests matching this subnet.
This is also known as the HUBs IP address or FQDN.
.. cfgcmd:: set protocols nhrp tunnel <tunnel> map register
The optional parameter register specifies that Registration Request should be
sent to this peer on startup.
This option is required when running a DMVPN spoke.
.. cfgcmd:: set protocols nhrp tunnel <tunnel> multicast <dynamic | nhs>
Determines how opennhrp daemon should soft switch the multicast traffic.
Currently, multicast traffic is captured by opennhrp daemon using a packet
socket, and resent back to proper destinations. This means that multicast
packet sending is CPU intensive.
Specfying nhs makes all multicast packets to be repeated to each statically
configured next hop.
Synamic instructs to forward to all peers which we have a direct connection
with. Alternatively, you can specify the directive multiple times for each
protocol-address the multicast traffic should be sent to.
.. warning:: It is very easy to misconfigure multicast repeating if you have
multiple NHSes.
.. cfgcmd:: set protocols nhrp tunnel <tunnel> non-caching
Disables caching of peer information from forwarded NHRP Resolution Reply
packets. This can be used to reduce memory consumption on big NBMA subnets.
.. note:: Currently does not do much as caching is not implemented.
.. cfgcmd:: set protocols nhrp tunnel <tunnel> redirect
Enable sending of Cisco style NHRP Traffic Indication packets. If this is
enabled and opennhrp detects a forwarded packet, it will send a message to
the original sender of the packet instructing it to create a direct connection
with the destination. This is basically a protocol independent equivalent of
ICMP redirect.
.. cfgcmd:: set protocols nhrp tunnel <tunnel> shortcut
Enable creation of shortcut routes.
A received NHRP Traffic Indication will trigger the resolution and
establishment of a shortcut route.
.. cfgcmd:: set protocols nhrp tunnel <tunnel> shortcut-destination
This instructs opennhrp to reply with authorative answers on NHRP Resolution
Requests destinied to addresses in this interface (instead of forwarding the
packets). This effectively allows the creation of shortcut routes to subnets
located on the interface.
When specified, this should be the only keyword for the interface.
.. cfgcmd:: set protocols nhrp tunnel <tunnel> shortcut-target <address>
Defines an off-NBMA network prefix for which the GRE interface will act as a
gateway. This an alternative to defining local interfaces with
shortcut-destination flag.
.. cfgcmd:: set protocols nhrp tunnel <tunnel> shortcut-target <address>
holding-time <timeout>
Specifies the holding time for NHRP Registration Requests and Resolution
Replies sent from this interface or shortcut-target. The holdtime is specified
in seconds and defaults to two hours.
*******
Example
*******
This blueprint uses VyOS as the DMVPN Hub and Cisco (7206VXR) and VyOS as
multiple spoke sites. The lab was build using :abbr:`EVE-NG (Emulated Virtual
Environment NG)`.
.. figure:: /_static/images/blueprint-dmvpn.png
:alt: DMVPN network
DMVPN example network
Each node (Hub and Spoke) uses an IP address from the network 172.16.253.128/29.
The below referenced IP address `192.0.2.1` is used as example address
representing a global unicast address under which the HUB can be contacted by
each and every individual spoke.
Configuration
=============
Hub
---
.. code-block:: none
set interfaces ethernet eth0 address 192.0.2.1/24
set interfaces tunnel tun100 address '172.16.253.134/29'
set interfaces tunnel tun100 encapsulation 'gre'
set interfaces tunnel tun100 local-ip '192.0.2.1'
set interfaces tunnel tun100 multicast 'enable'
set interfaces tunnel tun100 parameters ip key '1'
set protocols nhrp tunnel tun100 cisco-authentication 'secret'
set protocols nhrp tunnel tun100 holding-time '300'
set protocols nhrp tunnel tun100 multicast 'dynamic'
set protocols nhrp tunnel tun100 redirect
set protocols nhrp tunnel tun100 shortcut
set vpn ipsec esp-group ESP-HUB compression 'disable'
set vpn ipsec esp-group ESP-HUB lifetime '1800'
set vpn ipsec esp-group ESP-HUB mode 'tunnel'
set vpn ipsec esp-group ESP-HUB pfs 'dh-group2'
set vpn ipsec esp-group ESP-HUB proposal 1 encryption 'aes256'
set vpn ipsec esp-group ESP-HUB proposal 1 hash 'sha1'
set vpn ipsec esp-group ESP-HUB proposal 2 encryption '3des'
set vpn ipsec esp-group ESP-HUB proposal 2 hash 'md5'
set vpn ipsec ike-group IKE-HUB ikev2-reauth 'no'
set vpn ipsec ike-group IKE-HUB key-exchange 'ikev1'
set vpn ipsec ike-group IKE-HUB lifetime '3600'
set vpn ipsec ike-group IKE-HUB proposal 1 dh-group '2'
set vpn ipsec ike-group IKE-HUB proposal 1 encryption 'aes256'
set vpn ipsec ike-group IKE-HUB proposal 1 hash 'sha1'
set vpn ipsec ike-group IKE-HUB proposal 2 dh-group '2'
set vpn ipsec ike-group IKE-HUB proposal 2 encryption 'aes128'
set vpn ipsec ike-group IKE-HUB proposal 2 hash 'sha1'
set vpn ipsec ipsec-interfaces interface 'eth0'
set vpn ipsec profile NHRPVPN authentication mode 'pre-shared-secret'
set vpn ipsec profile NHRPVPN authentication pre-shared-secret 'secret'
set vpn ipsec profile NHRPVPN bind tunnel 'tun100'
set vpn ipsec profile NHRPVPN esp-group 'ESP-HUB'
set vpn ipsec profile NHRPVPN ike-group 'IKE-HUB'
.. note:: Setting this up on AWS will require a "Custom Protocol Rule" for
protocol number "47" (GRE) Allow Rule in TWO places. Firstly on the VPC
Network ACL, and secondly on the security group network ACL attached to the
EC2 instance. This has been tested as working for the official AMI image on
the AWS Marketplace. (Locate the correct VPC and security group by navigating
through the details pane below your EC2 instance in the AWS console).
Spoke
-----
The individual spoke configurations only differ in the local IP address on the
``tun10`` interface. See the above diagram for the individual IP addresses.
spoke01-spoke04
^^^^^^^^^^^^^^^
.. code-block:: none
crypto keyring DMVPN
pre-shared-key address 192.0.2.1 key secret
!
crypto isakmp policy 10
encr aes 256
authentication pre-share
group 2
crypto isakmp invalid-spi-recovery
crypto isakmp keepalive 30 30 periodic
crypto isakmp profile DMVPN
keyring DMVPN
match identity address 192.0.2.1 255.255.255.255
!
crypto ipsec transform-set DMVPN-AES256 esp-aes 256 esp-sha-hmac
mode transport
!
crypto ipsec profile DMVPN
set security-association idle-time 720
set transform-set DMVPN-AES256
set isakmp-profile DMVPN
!
interface Tunnel10
! individual spoke tunnel IP must change
ip address 172.16.253.129 255.255.255.248
no ip redirects
ip nhrp authentication secret
ip nhrp map 172.16.253.134 192.0.2.1
ip nhrp map multicast 192.0.2.1
ip nhrp network-id 1
ip nhrp holdtime 600
ip nhrp nhs 172.16.253.134
ip nhrp registration timeout 75
tunnel source FastEthernet0/0
tunnel mode gre multipoint
tunnel key 1
!
interface FastEthernet0/0
ip address dhcp
duplex half
spoke05
^^^^^^^
VyOS can also run in DMVPN spoke mode.
.. code-block:: none
set interfaces ethernet eth0 address 'dhcp'
set interfaces tunnel tun100 address '172.16.253.133/29'
set interfaces tunnel tun100 local-ip 0.0.0.0
set interfaces tunnel tun100 encapsulation 'gre'
set interfaces tunnel tun100 multicast 'enable'
set interfaces tunnel tun100 parameters ip key '1'
set protocols nhrp tunnel tun100 cisco-authentication 'secret'
set protocols nhrp tunnel tun100 holding-time '300'
set protocols nhrp tunnel tun100 map 172.16.253.134/29 nbma-address '92.0.2.1'
set protocols nhrp tunnel tun100 map 172.16.253.134/29 register
set protocols nhrp tunnel tun100 multicast 'nhs'
set protocols nhrp tunnel tun100 redirect
set protocols nhrp tunnel tun100 shortcut
set vpn ipsec esp-group ESP-HUB compression 'disable'
set vpn ipsec esp-group ESP-HUB lifetime '1800'
set vpn ipsec esp-group ESP-HUB mode 'tunnel'
set vpn ipsec esp-group ESP-HUB pfs 'dh-group2'
set vpn ipsec esp-group ESP-HUB proposal 1 encryption 'aes256'
set vpn ipsec esp-group ESP-HUB proposal 1 hash 'sha1'
set vpn ipsec esp-group ESP-HUB proposal 2 encryption '3des'
set vpn ipsec esp-group ESP-HUB proposal 2 hash 'md5'
set vpn ipsec ike-group IKE-HUB close-action 'none'
set vpn ipsec ike-group IKE-HUB ikev2-reauth 'no'
set vpn ipsec ike-group IKE-HUB key-exchange 'ikev1'
set vpn ipsec ike-group IKE-HUB lifetime '3600'
set vpn ipsec ike-group IKE-HUB proposal 1 dh-group '2'
set vpn ipsec ike-group IKE-HUB proposal 1 encryption 'aes256'
set vpn ipsec ike-group IKE-HUB proposal 1 hash 'sha1'
set vpn ipsec ike-group IKE-HUB proposal 2 dh-group '2'
set vpn ipsec ike-group IKE-HUB proposal 2 encryption 'aes128'
set vpn ipsec ike-group IKE-HUB proposal 2 hash 'sha1'
set vpn ipsec ipsec-interfaces interface 'eth0'
set vpn ipsec profile NHRPVPN authentication mode 'pre-shared-secret'
set vpn ipsec profile NHRPVPN authentication pre-shared-secret 'secret'
set vpn ipsec profile NHRPVPN bind tunnel 'tun100'
set vpn ipsec profile NHRPVPN esp-group 'ESP-HUB'
set vpn ipsec profile NHRPVPN ike-group 'IKE-HUB'
|
