#
# Synchronizer settings
#
Sync {
	Mode FTFW {
		#
		# Size of the buffer that hold destroy messages for 
		# possible resends (in bytes)
		#
		ResendBufferSize 262144

		#
		# Entries committed to the connection tracking table 
		# starts with a limited timeout of N seconds until the
		# takeover process is completed.
		#
		CommitTimeout 180

		# Set Acknowledgement window size
		ACKWindowSize 20
	}

	#
	# Multicast IP and interface where messages are
	# broadcasted (dedicated link). IMPORTANT: Make sure
	# that iptables accepts traffic for destination
	# 225.0.0.50, eg:
	#
	#	iptables -I INPUT -d 225.0.0.50 -j ACCEPT
	#	iptables -I OUTPUT -d 225.0.0.50 -j ACCEPT
	#
	Multicast {
		IPv4_address 225.0.0.50
		IPv4_interface 192.168.100.100 # IP of dedicated link
		Interface eth2
		Group 3780

		# The multicast sender uses a buffer to enqueue the packets
		# that are going to be transmitted. The default size of this
		# socket buffer is available at /proc/sys/net/core/wmem_default.
		# This value determines the chances to have an overrun in the
		# sender queue. The overrun results packet loss, thus, losing
		# state information that would have to be retransmitted. If you
		# notice some packet loss, you may want to increase the size
		# of the sender buffer.
		#
		# McastSndSocketBuffer 1249280
		#
		# The multicast receiver uses a buffer to enqueue the packets
		# that the socket is pending to handle. The default size of this
		# socket buffer is available at /proc/sys/net/core/rmem_default.
		# This value determines the chances to have an overrun in the
		# receiver queue. The overrun results packet loss, thus, losing
		# state information that would have to be retransmitted. If you
		# notice some packet loss, you may want to increase the size of
		# the receiver buffer.
		#
		# McastRcvSocketBuffer 1249280
	}

	# Enable/Disable message checksumming
	Checksum on

	# If you have a multiprimary setup (active-active) without connection
	# persistency, ie. you can't know which firewall handles a packet
	# that is part of a connection, then you need direct commit of
	# conntrack entries to the kernel conntrack table. OSPF setups must
	# set on this option. Default is Off.
	#
	# CacheWriteThrough On
}

#
# General settings
#
General {
	#
	# Number of buckets in the caches: hash table
	#
	HashSize 8192

	#
	# Maximum number of conntracks: 
	# it must be >= $ cat /proc/sys/net/ipv4/netfilter/ip_conntrack_max
	#
	HashLimit 65535

	#
	# Logfile: on (/var/log/conntrackd.log), off, or a filename
	# Default: off
	#
	#LogFile on

	#
	# Syslog: on, off or a facility name (daemon (default) or local0..7)
	# Default: off
	#
	#Syslog on

	#
	# Lockfile
	# 
	LockFile /var/lock/conntrack.lock

	#
	# Unix socket configuration
	#
	UNIX {
		Path /tmp/sync.sock
		Backlog 20
	}

	#
	# Netlink socket buffer size
	#
	SocketBufferSize 262142

	#
	# Increase the socket buffer up to maximum if required
	#
	SocketBufferSizeMaxGrown 655355

	#
	# Event filtering: This clause allows you to filter certain traffic,
	# There are currently three filter-sets: Protocol, Address and
	# State. The filter is attached to an action that can be: Accept or
	# Ignore. Thus, you can define the event filtering policy of the
	# filter-sets in positive or negative logic depending on your needs.
	#
	Filter {
		#
		# Accept only certain protocols: You may want to replicate
		# the state of flows depending on their layer 4 protocol.
		#
		Protocol Accept {
			TCP
		}

		#
		# Ignore traffic for a certain set of IP's: Usually all the
		# IP assigned to the firewall since local traffic must be
		# ignored, only forwarded connections are worth to replicate.
		#
		Address Ignore {
			IPv4_address 127.0.0.1 # loopback
			IPv4_address 192.168.0.1
			IPv4_address 192.168.1.1
			IPv4_address 192.168.100.100 # dedicated link ip
			IPv4_address 192.168.0.100 # virtual IP 1
			IPv4_address 192.168.1.100 # virtual IP 2
		}

		#
		# Uncomment this line below if you want to filter by flow state.
		# This option introduces a trade-off in the replication: it
		# reduces CPU consumption at the cost of having lazy backup 
		# firewall replicas. The existing TCP states are: SYN_SENT,
		# SYN_RECV, ESTABLISHED, FIN_WAIT, CLOSE_WAIT, LAST_ACK,
		# TIME_WAIT, CLOSED, LISTEN.
		#
		# State Accept {
		#	ESTABLISHED CLOSED TIME_WAIT CLOSE_WAIT for TCP
		# }
	}
}