1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
|
#
# Synchronizer settings
#
Sync {
Mode ALARM {
#
# If a conntrack entry is not modified in <= 15 seconds, then
# a message is broadcasted. This mechanism is used to
# resynchronize nodes that just joined the multicast group
#
RefreshTime 15
#
# If we don't receive a notification about the state of
# an entry in the external cache after N seconds, then
# remove it.
#
CacheTimeout 180
#
# Entries committed to the connection tracking table
# starts with a limited timeout of N seconds until the
# takeover process is completed.
#
CommitTimeout 180
#
# If the firewall replica goes from primary to backup,
# the conntrackd -t command is invoked in the script.
# This command resets the timers of the conntracks that
# live in the kernel to this new value. This is useful
# to purge the connection tracking table of zombie entries
# and avoid clashes with old entries if you trigger
# several consecutive hand-overs.
#
PurgeTimeout 15
}
#
# Multicast IP and interface where messages are
# broadcasted (dedicated link). IMPORTANT: Make sure
# that iptables accepts traffic for destination
# 225.0.0.50, eg:
#
# iptables -I INPUT -d 225.0.0.50 -j ACCEPT
# iptables -I OUTPUT -d 225.0.0.50 -j ACCEPT
#
Multicast {
#
# Multicast address: The address that you use as destination
# in the synchronization messages. You do not have to add
# this IP to any of your existing interfaces. If any doubt,
# do not modify this value.
#
IPv4_address 225.0.0.50
#
# The multicast group that identifies the cluster. If any
# doubt, do not modify this value.
#
Group 3780
#
# IP address of the interface that you are going to use to
# send the synchronization messages. Remember that you must
# use a dedicated link for the synchronization messages.
#
IPv4_interface 192.168.100.100
#
# The name of the interface that you are going to use to
# send the synchronization messages.
#
Interface eth2
# The multicast sender uses a buffer to enqueue the packets
# that are going to be transmitted. The default size of this
# socket buffer is available at /proc/sys/net/core/wmem_default.
# This value determines the chances to have an overrun in the
# sender queue. The overrun results packet loss, thus, losing
# state information that would have to be retransmitted. If you
# notice some packet loss, you may want to increase the size
# of the sender buffer.
#
# McastSndSocketBuffer 1249280
# The multicast receiver uses a buffer to enqueue the packets
# that the socket is pending to handle. The default size of this
# socket buffer is available at /proc/sys/net/core/rmem_default.
# This value determines the chances to have an overrun in the
# receiver queue. The overrun results packet loss, thus, losing
# state information that would have to be retransmitted. If you
# notice some packet loss, you may want to increase the size of
# the receiver buffer.
#
# McastRcvSocketBuffer 1249280
}
#
# Enable/Disable message checksumming. This is a good property to
# achieve fault-tolerance. In case of doubt, do not modify this value.
#
Checksum on
}
#
# General settings
#
General {
#
# Number of buckets in the caches: hash table.
#
HashSize 16384
#
# Maximum number of conntracks:
# it must be >= $ cat /proc/sys/net/ipv4/netfilter/ip_conntrack_max
#
HashLimit 65536
#
# Logfile: on (/var/log/conntrackd.log), off, or a filename
# Default: off
#
LogFile on
#
# Syslog: on, off or a facility name (daemon (default) or local0..7)
# Default: off
#
#Syslog on
#
# Lockfile
#
LockFile /var/lock/conntrack.lock
#
# Unix socket configuration
#
UNIX {
Path /var/run/conntrackd.ctl
Backlog 20
}
#
# Netlink socket buffer size
#
SocketBufferSize 262142
#
# Increase the socket buffer up to maximum if required
#
SocketBufferSizeMaxGrown 655355
#
# Event filtering: This clause allows you to filter certain traffic,
# There are currently three filter-sets: Protocol, Address and
# State. The filter is attached to an action that can be: Accept or
# Ignore. Thus, you can define the event filtering policy of the
# filter-sets in positive or negative logic depending on your needs.
#
Filter {
#
# Accept only certain protocols: You may want to replicate
# the state of flows depending on their layer 4 protocol.
#
Protocol Accept {
TCP
}
#
# Ignore traffic for a certain set of IP's: Usually all the
# IP assigned to the firewall since local traffic must be
# ignored, only forwarded connections are worth to replicate.
# Note that these values depends on the local IPs that are
# assigned to the firewall.
#
Address Ignore {
IPv4_address 127.0.0.1 # loopback
IPv4_address 192.168.0.100 # virtual IP 1
IPv4_address 192.168.1.100 # virtual IP 2
IPv4_address 192.168.0.1
IPv4_address 192.168.1.1
IPv4_address 192.168.100.100 # dedicated link ip
}
#
# Uncomment this line below if you want to filter by flow state.
# This option introduces a trade-off in the replication: it
# reduces CPU consumption at the cost of having lazy backup
# firewall replicas. The existing TCP states are: SYN_SENT,
# SYN_RECV, ESTABLISHED, FIN_WAIT, CLOSE_WAIT, LAST_ACK,
# TIME_WAIT, CLOSED, LISTEN.
#
# State Accept {
# ESTABLISHED CLOSED TIME_WAIT CLOSE_WAIT for TCP
# }
}
}
|
