snmp: T3606: Install MIBs into well known location

FRR also expects the MIBs in /usr/share/snmp/mibs

1 files changed, 0 insertions, 1443 deletions

diff --git a/data/mibs/IPV6-MIB.txt b/data/mibs/IPV6-MIB.txt
deleted file mode 100644
index 6957af27f..000000000
--- a/data/mibs/IPV6-MIB.txt
+++ /dev/null
@@ -1,1443 +0,0 @@
- IPV6-MIB DEFINITIONS ::= BEGIN
-
- IMPORTS
-     MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE,
-     mib-2, Counter32, Unsigned32, Integer32,
-     Gauge32                               FROM SNMPv2-SMI
-     DisplayString, PhysAddress, TruthValue, TimeStamp,
-     VariablePointer, RowPointer           FROM SNMPv2-TC
-     MODULE-COMPLIANCE, OBJECT-GROUP,
-     NOTIFICATION-GROUP                    FROM SNMPv2-CONF
-     Ipv6IfIndex, Ipv6Address, Ipv6AddressPrefix,
-     Ipv6AddressIfIdentifier,
-     Ipv6IfIndexOrZero                     FROM IPV6-TC;
-
- ipv6MIB MODULE-IDENTITY
-     LAST-UPDATED "9802052155Z"
-     ORGANIZATION "IETF IPv6 Working Group"
-     CONTACT-INFO
-       "           Dimitry Haskin
-
-           Postal: Bay Networks, Inc.
-                   660 Techology Park Drive.
-                   Billerica, MA  01821
-
-                   US
-
-              Tel: +1-978-916-8124
-           E-mail: dhaskin@baynetworks.com
-
-                   Steve Onishi
-
-           Postal: Bay Networks, Inc.
-                   3 Federal Street
-                   Billerica, MA 01821
-                   US
-
-              Tel: +1-978-916-3816
-           E-mail: sonishi@baynetworks.com"
-     DESCRIPTION
-       "The MIB module for entities implementing the IPv6
-        protocol."
-     ::= { mib-2 55 }
-
- -- the IPv6 general group
-
- ipv6MIBObjects OBJECT IDENTIFIER   ::= { ipv6MIB 1 }
-
- ipv6Forwarding OBJECT-TYPE
-     SYNTAX      INTEGER {
-                  forwarding(1),    -- acting as a router
-
-                                    -- NOT acting as
-                  notForwarding(2)  -- a router
-                 }
-      MAX-ACCESS read-write
-      STATUS     current
-      DESCRIPTION
-        "The indication of whether this entity is acting
-        as an IPv6 router in respect to the forwarding of
-        datagrams received by, but not addressed to, this
-        entity.  IPv6 routers forward datagrams.  IPv6
-        hosts do not (except those source-routed via the
-        host).
-
-        Note that for some managed nodes, this object may
-        take on only a subset of the values possible.
-        Accordingly, it is appropriate for an agent to
-        return a `wrongValue' response if a management
-        station attempts to change this object to an
-        inappropriate value."
-      ::= { ipv6MIBObjects 1 }
-
- ipv6DefaultHopLimit OBJECT-TYPE
-     SYNTAX      INTEGER(0..255)
-     MAX-ACCESS  read-write
-      STATUS     current
-     DESCRIPTION
-        "The default value inserted into the Hop Limit
-        field of the IPv6 header of datagrams originated
-        at this entity, whenever a Hop Limit value is not
-        supplied by the transport layer protocol."
-     DEFVAL  { 64 }
-     ::= { ipv6MIBObjects 2 }
-
-ipv6Interfaces OBJECT-TYPE
-     SYNTAX      Unsigned32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-       "The number of IPv6 interfaces (regardless of
-        their current state) present on this system."
-     ::= { ipv6MIBObjects 3 }
-
-ipv6IfTableLastChange OBJECT-TYPE
-     SYNTAX      TimeStamp
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-       "The value of sysUpTime at the time of the last
-       insertion or removal of an entry in the
-       ipv6IfTable. If the number of entries has been
-       unchanged since the last re-initialization of
-       the local network management subsystem, then this
-       object contains a zero value."
-     ::= { ipv6MIBObjects 4 }
-
--- the IPv6 Interfaces table
-
-ipv6IfTable OBJECT-TYPE
-     SYNTAX     SEQUENCE OF Ipv6IfEntry
-     MAX-ACCESS not-accessible
-     STATUS     current
-     DESCRIPTION
-       "The IPv6 Interfaces table contains information
-       on the entity's internetwork-layer interfaces.
-       An IPv6 interface constitutes a logical network
-       layer attachment to the layer immediately below
-
-       IPv6 including internet layer 'tunnels', such as
-       tunnels over IPv4 or IPv6 itself."
-     ::= { ipv6MIBObjects 5 }
-
- ipv6IfEntry OBJECT-TYPE
-     SYNTAX     Ipv6IfEntry
-     MAX-ACCESS not-accessible
-     STATUS     current
-     DESCRIPTION
-       "An interface entry containing objects
-        about a particular IPv6 interface."
-     INDEX   { ipv6IfIndex }
-     ::= { ipv6IfTable 1 }
-
- Ipv6IfEntry ::= SEQUENCE {
-         ipv6IfIndex              Ipv6IfIndex,
-         ipv6IfDescr              DisplayString,
-         ipv6IfLowerLayer         VariablePointer,
-         ipv6IfEffectiveMtu       Unsigned32,
-         ipv6IfReasmMaxSize       Unsigned32,
-         ipv6IfIdentifier         Ipv6AddressIfIdentifier,
-         ipv6IfIdentifierLength   INTEGER,
-         ipv6IfPhysicalAddress    PhysAddress,
-         ipv6IfAdminStatus        INTEGER,
-         ipv6IfOperStatus         INTEGER,
-         ipv6IfLastChange         TimeStamp
-     }
-
- ipv6IfIndex OBJECT-TYPE
-     SYNTAX     Ipv6IfIndex
-     MAX-ACCESS not-accessible
-     STATUS     current
-     DESCRIPTION
-       "A unique non-zero value identifying
-        the particular IPv6 interface."
-     ::= { ipv6IfEntry 1 }
-
- ipv6IfDescr OBJECT-TYPE
-     SYNTAX     DisplayString
-     MAX-ACCESS read-write
-     STATUS     current
-     DESCRIPTION
-       "A textual string containing information about the
-       interface.  This string may be set by the network
-       management system."
-     ::= { ipv6IfEntry 2 }
-
- ipv6IfLowerLayer OBJECT-TYPE
-    SYNTAX      VariablePointer
-    MAX-ACCESS  read-only
-    STATUS      current
-    DESCRIPTION
-      "This object identifies the protocol layer over
-       which this network interface operates.  If this
-       network interface operates over the data-link
-       layer, then the value of this object refers to an
-       instance of ifIndex [6]. If this network interface
-       operates over an IPv4 interface, the value of this
-       object refers to an instance of ipAdEntAddr [3].
-
-       If this network interface operates over another
-       IPv6 interface, the value of this object refers to
-       an instance of ipv6IfIndex.  If this network
-       interface is not currently operating over an active
-       protocol layer, then the value of this object
-       should be set to the OBJECT ID { 0 0 }."
-    ::= { ipv6IfEntry 3 }
-
- ipv6IfEffectiveMtu OBJECT-TYPE
-    SYNTAX      Unsigned32
-    UNITS       "octets"
-    MAX-ACCESS  read-only
-    STATUS      current
-    DESCRIPTION
-      "The size of the largest IPv6 packet which can be
-      sent/received on the interface, specified in
-      octets."
- ::= { ipv6IfEntry 4 }
-
- ipv6IfReasmMaxSize OBJECT-TYPE
-    SYNTAX      Unsigned32 (0..65535)
-    UNITS       "octets"
-    MAX-ACCESS  read-only
-    STATUS      current
-    DESCRIPTION
-      "The size of the largest IPv6 datagram which this
-      entity can re-assemble from incoming IPv6 fragmented
-      datagrams received on this interface."
- ::= { ipv6IfEntry 5 }
-
- ipv6IfIdentifier OBJECT-TYPE
-     SYNTAX      Ipv6AddressIfIdentifier
-     MAX-ACCESS  read-write
-     STATUS      current
-     DESCRIPTION
-        "The Interface Identifier for this interface that
-
-        is (at least) unique on the link this interface is
-        attached to. The Interface Identifier is combined
-        with an address prefix to form an interface address.
-
-        By default, the Interface Identifier is autoconfigured
-        according to the rules of the link type this
-        interface is attached to."
-     ::= { ipv6IfEntry 6 }
-
- ipv6IfIdentifierLength OBJECT-TYPE
-     SYNTAX      INTEGER (0..64)
-     UNITS       "bits"
-     MAX-ACCESS  read-write
-     STATUS      current
-     DESCRIPTION
-       "The length of the Interface Identifier in bits."
-     ::= { ipv6IfEntry 7 }
-
- ipv6IfPhysicalAddress OBJECT-TYPE
-     SYNTAX      PhysAddress
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-       "The interface's physical address. For example, for
-       an IPv6 interface attached to an 802.x link, this
-       object normally contains a MAC address. Note that
-       in some cases this address may differ from the
-       address of the interface's protocol sub-layer.  The
-       interface's media-specific MIB must define the bit
-       and byte ordering and the format of the value of
-       this object. For interfaces which do not have such
-       an address (e.g., a serial line), this object should
-       contain an octet string of zero length."
-     ::= { ipv6IfEntry 8 }
-
-ipv6IfAdminStatus OBJECT-TYPE
-    SYNTAX  INTEGER {
-             up(1),       -- ready to pass packets
-             down(2)
-            }
-    MAX-ACCESS  read-write
-    STATUS      current
-    DESCRIPTION
-      "The desired state of the interface.  When a managed
-      system initializes,  all IPv6 interfaces start with
-      ipv6IfAdminStatus in the down(2) state.  As a result
-      of either explicit management action or per
-      configuration information retained by the managed
-
-      system,  ipv6IfAdminStatus is then changed to
-      the up(1) state (or remains in the down(2) state)."
-    ::= { ipv6IfEntry 9 }
-
-ipv6IfOperStatus OBJECT-TYPE
-    SYNTAX  INTEGER {
-             up(1),             -- ready to pass packets
-
-             down(2),
-             noIfIdentifier(3), -- no interface identifier
-
-                                -- status can not be
-                                -- determined for some
-             unknown(4),        -- reason
-
-                                -- some component is
-             notPresent(5)      -- missing
-            }
-    MAX-ACCESS  read-only
-    STATUS      current
-    DESCRIPTION
-      "The current operational state of the interface.
-      The noIfIdentifier(3) state indicates that no valid
-      Interface Identifier is assigned to the interface.
-      This state usually indicates that the link-local
-      interface address failed Duplicate Address Detection.
-      If ipv6IfAdminStatus is down(2) then ipv6IfOperStatus
-      should be down(2).  If ipv6IfAdminStatus is changed
-      to up(1) then ipv6IfOperStatus should change to up(1)
-      if the interface is ready to transmit and receive
-      network traffic; it should remain in the down(2) or
-      noIfIdentifier(3) state if and only if there is a
-      fault that prevents it from going to the up(1) state;
-      it should remain in the notPresent(5) state if
-      the interface has missing (typically, lower layer)
-      components."
-    ::= { ipv6IfEntry 10 }
-
-ipv6IfLastChange OBJECT-TYPE
-    SYNTAX      TimeStamp
-    MAX-ACCESS  read-only
-    STATUS      current
-    DESCRIPTION
-        "The value of sysUpTime at the time the interface
-        entered its current operational state.  If the
-        current state was entered prior to the last
-        re-initialization of the local network management
-
-        subsystem, then this object contains a zero
-        value."
-    ::= { ipv6IfEntry 11 }
-
- --  IPv6 Interface Statistics table
-
- ipv6IfStatsTable OBJECT-TYPE
-     SYNTAX     SEQUENCE OF Ipv6IfStatsEntry
-     MAX-ACCESS not-accessible
-     STATUS     current
-     DESCRIPTION
-         "IPv6 interface traffic statistics."
-     ::= { ipv6MIBObjects 6 }
-
- ipv6IfStatsEntry OBJECT-TYPE
-     SYNTAX     Ipv6IfStatsEntry
-     MAX-ACCESS not-accessible
-     STATUS     current
-     DESCRIPTION
-         "An interface statistics entry containing objects
-         at a particular IPv6 interface."
-     AUGMENTS { ipv6IfEntry }
-     ::= { ipv6IfStatsTable 1 }
-
- Ipv6IfStatsEntry ::= SEQUENCE {
-         ipv6IfStatsInReceives
-             Counter32,
-         ipv6IfStatsInHdrErrors
-             Counter32,
-         ipv6IfStatsInTooBigErrors
-             Counter32,
-         ipv6IfStatsInNoRoutes
-             Counter32,
-         ipv6IfStatsInAddrErrors
-             Counter32,
-         ipv6IfStatsInUnknownProtos
-             Counter32,
-         ipv6IfStatsInTruncatedPkts
-             Counter32,
-         ipv6IfStatsInDiscards
-             Counter32,
-         ipv6IfStatsInDelivers
-             Counter32,
-         ipv6IfStatsOutForwDatagrams
-             Counter32,
-         ipv6IfStatsOutRequests
-             Counter32,
-         ipv6IfStatsOutDiscards
-
-             Counter32,
-         ipv6IfStatsOutFragOKs
-             Counter32,
-         ipv6IfStatsOutFragFails
-             Counter32,
-         ipv6IfStatsOutFragCreates
-             Counter32,
-         ipv6IfStatsReasmReqds
-             Counter32,
-         ipv6IfStatsReasmOKs
-             Counter32,
-         ipv6IfStatsReasmFails
-             Counter32,
-         ipv6IfStatsInMcastPkts
-             Counter32,
-         ipv6IfStatsOutMcastPkts
-             Counter32
-     }
-
- ipv6IfStatsInReceives OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-        "The total number of input datagrams received by
-        the interface, including those received in error."
-     ::= { ipv6IfStatsEntry 1 }
-
- ipv6IfStatsInHdrErrors OBJECT-TYPE
-     SYNTAX     Counter32
-     MAX-ACCESS read-only
-     STATUS     current
-     DESCRIPTION
-        "The number of input datagrams discarded due to
-        errors in their IPv6 headers, including version
-        number mismatch, other format errors, hop count
-        exceeded, errors discovered in processing their
-        IPv6 options, etc."
-     ::= { ipv6IfStatsEntry 2 }
-
- ipv6IfStatsInTooBigErrors OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-       "The number of input datagrams that could not be
-       forwarded because their size exceeded the link MTU
-       of outgoing interface."
-     ::= { ipv6IfStatsEntry 3 }
-
- ipv6IfStatsInNoRoutes OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-        "The number of input datagrams discarded because no
-         route could be found to transmit them to their
-         destination."
-     ::= { ipv6IfStatsEntry 4 }
-
- ipv6IfStatsInAddrErrors OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-        "The number of input datagrams discarded because
-        the IPv6 address in their IPv6 header's destination
-        field was not a valid address to be received at
-        this entity.  This count includes invalid
-        addresses (e.g., ::0) and unsupported addresses
-        (e.g., addresses with unallocated prefixes).  For
-        entities which are not IPv6 routers and therefore
-        do not forward datagrams, this counter includes
-        datagrams discarded because the destination address
-        was not a local address."
-     ::= { ipv6IfStatsEntry 5 }
-
- ipv6IfStatsInUnknownProtos OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-        "The number of locally-addressed datagrams
-        received successfully but discarded because of an
-        unknown or unsupported protocol. This counter is
-        incremented at the interface to which these
-        datagrams were addressed which might not be
-        necessarily the input interface for some of
-        the datagrams."
-     ::= { ipv6IfStatsEntry 6 }
-
- ipv6IfStatsInTruncatedPkts OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-        "The number of input datagrams discarded because
-         datagram frame didn't carry enough data."
-     ::= { ipv6IfStatsEntry 7 }
-
- ipv6IfStatsInDiscards OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-        "The number of input IPv6 datagrams for which no
-        problems were encountered to prevent their
-        continued processing, but which were discarded
-        (e.g., for lack of buffer space).  Note that this
-        counter does not include any datagrams discarded
-        while awaiting re-assembly."
-     ::= { ipv6IfStatsEntry 8 }
-
- ipv6IfStatsInDelivers OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-      "The total number of datagrams successfully
-      delivered to IPv6 user-protocols (including ICMP).
-      This counter is incremented at the interface to
-      which these datagrams were addressed which might
-      not be necessarily the input interface for some of
-      the datagrams."
-     ::= { ipv6IfStatsEntry 9 }
-
- ipv6IfStatsOutForwDatagrams OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-        "The number of output datagrams which this
-        entity received and forwarded to their final
-        destinations.  In entities which do not act
-        as IPv6 routers, this counter will include
-        only those packets which were Source-Routed
-        via this entity, and the Source-Route
-        processing was successful.  Note that for
-        a successfully forwarded datagram the counter
-        of the outgoing interface is incremented."
-     ::= { ipv6IfStatsEntry 10 }
-
- ipv6IfStatsOutRequests OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-      "The total number of IPv6 datagrams which local IPv6
-      user-protocols (including ICMP) supplied to IPv6 in
-      requests for transmission.  Note that this counter
-      does not include any datagrams counted in
-      ipv6IfStatsOutForwDatagrams."
-     ::= { ipv6IfStatsEntry 11 }
-
- ipv6IfStatsOutDiscards OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-         "The number of output IPv6 datagrams for which no
-         problem was encountered to prevent their
-         transmission to their destination, but which were
-         discarded (e.g., for lack of buffer space).  Note
-         that this counter would include datagrams counted
-         in ipv6IfStatsOutForwDatagrams if any such packets
-         met this (discretionary) discard criterion."
-     ::= { ipv6IfStatsEntry 12 }
-
- ipv6IfStatsOutFragOKs OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-        "The number of IPv6 datagrams that have been
-         successfully fragmented at this output interface."
-     ::= { ipv6IfStatsEntry 13 }
-
- ipv6IfStatsOutFragFails OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-        "The number of IPv6 datagrams that have been
-         discarded because they needed to be fragmented
-         at this output interface but could not be."
-     ::= { ipv6IfStatsEntry 14 }
-
- ipv6IfStatsOutFragCreates OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-        "The number of output datagram fragments that have
-         been generated as a result of fragmentation at
-         this output interface."
-     ::= { ipv6IfStatsEntry 15 }
-
- ipv6IfStatsReasmReqds OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-        "The number of IPv6 fragments received which needed
-         to be reassembled at this interface.  Note that this
-         counter is incremented at the interface to which
-         these fragments were addressed which might not
-         be necessarily the input interface for some of
-         the fragments."
-     ::= { ipv6IfStatsEntry 16 }
-
- ipv6IfStatsReasmOKs OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-       "The number of IPv6 datagrams successfully
-       reassembled.  Note that this counter is incremented
-       at the interface to which these datagrams were
-       addressed which might not be necessarily the input
-       interface for some of the fragments."
-     ::= { ipv6IfStatsEntry 17 }
-
- ipv6IfStatsReasmFails OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-        "The number of failures detected by the IPv6 re-
-        assembly algorithm (for whatever reason: timed
-        out, errors, etc.).  Note that this is not
-        necessarily a count of discarded IPv6 fragments
-        since some algorithms (notably the algorithm in
-        RFC 815) can lose track of the number of fragments
-        by combining them as they are received.
-        This counter is incremented at the interface to which
-        these fragments were addressed which might not be
-        necessarily the input interface for some of the
-        fragments."
-     ::= { ipv6IfStatsEntry 18 }
-
- ipv6IfStatsInMcastPkts OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS     current
-     DESCRIPTION
-        "The number of multicast packets received
-         by the interface"
-     ::= { ipv6IfStatsEntry 19 }
-
- ipv6IfStatsOutMcastPkts OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-        "The number of multicast packets transmitted
-         by the interface"
-     ::= { ipv6IfStatsEntry 20 }
-
- -- Address Prefix table
-
- -- The IPv6 Address Prefix table contains information on
- -- the entity's IPv6 Address Prefixes that are associated
- -- with IPv6 interfaces.
-
- ipv6AddrPrefixTable OBJECT-TYPE
-     SYNTAX  SEQUENCE OF Ipv6AddrPrefixEntry
-     MAX-ACCESS  not-accessible
-     STATUS      current
-     DESCRIPTION
-         "The list of IPv6 address prefixes of
-         IPv6 interfaces."
-     ::= { ipv6MIBObjects 7 }
-
- ipv6AddrPrefixEntry OBJECT-TYPE
-     SYNTAX  Ipv6AddrPrefixEntry
-     MAX-ACCESS  not-accessible
-     STATUS      current
-     DESCRIPTION
-         "An interface entry containing objects of
-         a particular IPv6 address prefix."
-     INDEX   { ipv6IfIndex,
-               ipv6AddrPrefix,
-               ipv6AddrPrefixLength }
-     ::= { ipv6AddrPrefixTable 1 }
-
- Ipv6AddrPrefixEntry ::= SEQUENCE {
-
-      ipv6AddrPrefix                     Ipv6AddressPrefix,
-      ipv6AddrPrefixLength               INTEGER (0..128),
-      ipv6AddrPrefixOnLinkFlag           TruthValue,
-      ipv6AddrPrefixAutonomousFlag       TruthValue,
-      ipv6AddrPrefixAdvPreferredLifetime Unsigned32,
-      ipv6AddrPrefixAdvValidLifetime     Unsigned32
-     }
-
- ipv6AddrPrefix OBJECT-TYPE
-     SYNTAX      Ipv6AddressPrefix
-     MAX-ACCESS  not-accessible
-     STATUS      current
-     DESCRIPTION
-       "The prefix associated with the this interface."
-     ::= { ipv6AddrPrefixEntry 1 }
-
- ipv6AddrPrefixLength OBJECT-TYPE
-     SYNTAX      INTEGER (0..128)
-     UNITS       "bits"
-     MAX-ACCESS  not-accessible
-     STATUS      current
-     DESCRIPTION
-       "The length of the prefix (in bits)."
-     ::= { ipv6AddrPrefixEntry 2 }
-
- ipv6AddrPrefixOnLinkFlag OBJECT-TYPE
-     SYNTAX      TruthValue
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-       "This object has the value 'true(1)', if this
-       prefix can be used  for on-link determination
-       and the value 'false(2)' otherwise."
-     ::= { ipv6AddrPrefixEntry 3 }
-
- ipv6AddrPrefixAutonomousFlag OBJECT-TYPE
-     SYNTAX      TruthValue
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-       "Autonomous address configuration flag. When
-       true(1), indicates that this prefix can be used
-       for autonomous address configuration (i.e. can
-       be used to form a local interface address).
-       If false(2), it is not used to autoconfigure
-       a local interface address."
-     ::= { ipv6AddrPrefixEntry 4 }
-
- ipv6AddrPrefixAdvPreferredLifetime OBJECT-TYPE
-     SYNTAX      Unsigned32
-     UNITS       "seconds"
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-        "It is the length of time in seconds that this
-        prefix will remain preferred, i.e. time until
-        deprecation.  A value of 4,294,967,295 represents
-        infinity.
-
-        The address generated from a deprecated prefix
-        should no longer be used as a source address in
-        new communications, but packets received on such
-        an interface are processed as expected."
-     ::= { ipv6AddrPrefixEntry 5 }
-
- ipv6AddrPrefixAdvValidLifetime OBJECT-TYPE
-     SYNTAX      Unsigned32
-     UNITS       "seconds"
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-       "It is the length of time in seconds that this
-       prefix will remain valid, i.e. time until
-       invalidation.  A value of 4,294,967,295 represents
-       infinity.
-
-       The address generated from an invalidated prefix
-       should not appear as the destination or source
-       address of a packet."
-     ::= { ipv6AddrPrefixEntry 6 }
-
- -- the IPv6 Address table
-
- -- The IPv6 address table contains this node's IPv6
- -- addressing information.
-
- ipv6AddrTable OBJECT-TYPE
-    SYNTAX      SEQUENCE OF Ipv6AddrEntry
-    MAX-ACCESS  not-accessible
-    STATUS      current
-    DESCRIPTION
-      "The table of addressing information relevant to
-      this node's interface addresses."
-    ::= { ipv6MIBObjects 8 }
-
- ipv6AddrEntry OBJECT-TYPE
-    SYNTAX      Ipv6AddrEntry
-    MAX-ACCESS  not-accessible
-    STATUS      current
-    DESCRIPTION
-        "The addressing information for one of this
-        node's interface addresses."
-    INDEX   { ipv6IfIndex, ipv6AddrAddress }
-    ::= { ipv6AddrTable 1 }
-
- Ipv6AddrEntry ::=
-    SEQUENCE {
-         ipv6AddrAddress        Ipv6Address,
-         ipv6AddrPfxLength      INTEGER,
-         ipv6AddrType           INTEGER,
-         ipv6AddrAnycastFlag    TruthValue,
-         ipv6AddrStatus         INTEGER
-        }
-
- ipv6AddrAddress OBJECT-TYPE
-    SYNTAX      Ipv6Address
-    MAX-ACCESS  not-accessible
-    STATUS      current
-    DESCRIPTION
-      "The IPv6 address to which this entry's addressing
-      information pertains."
-    ::= { ipv6AddrEntry 1 }
-
- ipv6AddrPfxLength OBJECT-TYPE
-    SYNTAX      INTEGER(0..128)
-    UNITS       "bits"
-    MAX-ACCESS  read-only
-    STATUS      current
-    DESCRIPTION
-      "The length of the prefix (in bits) associated with
-      the IPv6 address of this entry."
-    ::= { ipv6AddrEntry 2 }
-
- ipv6AddrType OBJECT-TYPE
-    SYNTAX      INTEGER {
-                        -- address has been formed
-                        -- using stateless
-         stateless(1),  -- autoconfiguration
-
-                        -- address has been acquired
-                        -- by stateful means
-                        -- (e.g. DHCPv6, manual
-         stateful(2),   -- configuration)
-
-                        -- type can not be determined
-         unknown(3)     -- for some reason.
-       }
-    MAX-ACCESS  read-only
-    STATUS      current
-    DESCRIPTION
-       "The type of address. Note that 'stateless(1)'
-       refers to an address that was statelessly
-       autoconfigured; 'stateful(2)' refers to a address
-       which was acquired by via a stateful protocol
-       (e.g. DHCPv6, manual configuration)."
-    ::= { ipv6AddrEntry 3 }
-
- ipv6AddrAnycastFlag OBJECT-TYPE
-     SYNTAX      TruthValue
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-       "This object has the value 'true(1)', if this
-       address is an anycast address and the value
-       'false(2)' otherwise."
-     ::= { ipv6AddrEntry 4 }
-
- ipv6AddrStatus OBJECT-TYPE
-    SYNTAX      INTEGER {
-             preferred(1),
-             deprecated(2),
-             invalid(3),
-             inaccessible(4),
-             unknown(5)   -- status can not be determined
-                          -- for some reason.
-            }
-    MAX-ACCESS  read-only
-    STATUS      current
-    DESCRIPTION
-      "Address status.  The preferred(1) state indicates
-      that this is a valid address that can appear as
-      the destination or source address of a packet.
-      The deprecated(2) state indicates that this is
-      a valid but deprecated address that should no longer
-      be used as a source address in new communications,
-      but packets addressed to such an address are
-      processed as expected. The invalid(3) state indicates
-      that this is not valid address which should not
-
-      appear as the destination or source address of
-      a packet. The inaccessible(4) state indicates that
-      the address is not accessible because the interface
-      to which this address is assigned is not operational."
-    ::= { ipv6AddrEntry 5 }
-
- -- IPv6 Routing objects
-
- ipv6RouteNumber OBJECT-TYPE
-     SYNTAX      Gauge32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-       "The number of current ipv6RouteTable entries.
-       This is primarily to avoid having to read
-       the table in order to determine this number."
-     ::= { ipv6MIBObjects 9 }
-
- ipv6DiscardedRoutes OBJECT-TYPE
-     SYNTAX      Counter32
-     MAX-ACCESS  read-only
-     STATUS      current
-     DESCRIPTION
-       "The number of routing entries which were chosen
-        to be discarded even though they are valid.  One
-        possible reason for discarding such an entry could
-        be to free-up buffer space for other routing
-        entries."
-     ::= { ipv6MIBObjects 10 }
-
- -- IPv6 Routing table
-
- ipv6RouteTable OBJECT-TYPE
-     SYNTAX     SEQUENCE OF Ipv6RouteEntry
-     MAX-ACCESS not-accessible
-     STATUS     current
-     DESCRIPTION
-       "IPv6 Routing table. This table contains
-       an entry for each valid IPv6 unicast route
-       that can be used for packet forwarding
-       determination."
-     ::= { ipv6MIBObjects 11 }
-
- ipv6RouteEntry OBJECT-TYPE
-     SYNTAX     Ipv6RouteEntry
-     MAX-ACCESS not-accessible
-     STATUS     current
-     DESCRIPTION
-             "A routing entry."
-     INDEX   { ipv6RouteDest,
-               ipv6RoutePfxLength,
-               ipv6RouteIndex }
-     ::= { ipv6RouteTable 1 }
-
- Ipv6RouteEntry ::= SEQUENCE {
-         ipv6RouteDest           Ipv6Address,
-         ipv6RoutePfxLength      INTEGER,
-         ipv6RouteIndex          Unsigned32,
-         ipv6RouteIfIndex        Ipv6IfIndexOrZero,
-         ipv6RouteNextHop        Ipv6Address,
-         ipv6RouteType           INTEGER,
-         ipv6RouteProtocol       INTEGER,
-         ipv6RoutePolicy         Integer32,
-         ipv6RouteAge            Unsigned32,
-         ipv6RouteNextHopRDI     Unsigned32,
-         ipv6RouteMetric         Unsigned32,
-         ipv6RouteWeight         Unsigned32,
-         ipv6RouteInfo           RowPointer,
-         ipv6RouteValid          TruthValue
-     }
-
- ipv6RouteDest OBJECT-TYPE
-     SYNTAX     Ipv6Address
-     MAX-ACCESS not-accessible
-     STATUS     current
-     DESCRIPTION
-       "The destination IPv6 address of this route.
-       This object may not take a Multicast address
-       value."
-     ::= { ipv6RouteEntry 1 }
-
- ipv6RoutePfxLength OBJECT-TYPE
-     SYNTAX     INTEGER(0..128)
-     UNITS      "bits"
-     MAX-ACCESS not-accessible
-     STATUS     current
-     DESCRIPTION
-       "Indicates the prefix length of the destination
-       address."
-     ::= { ipv6RouteEntry 2 }
-
- ipv6RouteIndex OBJECT-TYPE
-     SYNTAX     Unsigned32
-     MAX-ACCESS not-accessible
-     STATUS     current
-     DESCRIPTION
-       "The value which uniquely identifies the route
-       among the routes to the same network layer
-       destination.  The way this value is chosen is
-       implementation specific but it must be unique for
-       ipv6RouteDest/ipv6RoutePfxLength pair and remain
-       constant for the life of the route."
-     ::= { ipv6RouteEntry 3 }
-
- ipv6RouteIfIndex OBJECT-TYPE
-     SYNTAX     Ipv6IfIndexOrZero
-     MAX-ACCESS read-only
-     STATUS     current
-     DESCRIPTION
-       "The index value which uniquely identifies the local
-       interface through which the next hop of this
-       route should be reached.  The interface identified
-       by a particular value of this index is the same
-       interface as identified by the same value of
-       ipv6IfIndex.  For routes of the discard type this
-       value can be zero."
-     ::= { ipv6RouteEntry 4 }
-
- ipv6RouteNextHop OBJECT-TYPE
-     SYNTAX     Ipv6Address
-     MAX-ACCESS read-only
-     STATUS     current
-     DESCRIPTION
-       "On remote routes, the address of the next
-       system en route;  otherwise, ::0
-       ('00000000000000000000000000000000'H in ASN.1
-       string representation)."
-     ::= { ipv6RouteEntry 5 }
-
- ipv6RouteType OBJECT-TYPE
-     SYNTAX     INTEGER {
-        other(1),     -- none of the following
-
-                      -- an route indicating that
-                      -- packets to destinations
-                      -- matching this route are
-        discard(2),   -- to be discarded
-
-                      -- route to directly
-        local(3),     -- connected (sub-)network
-
-                      -- route to a remote
-
-        remote(4)     -- destination
-
-     }
-     MAX-ACCESS read-only
-     STATUS     current
-     DESCRIPTION
-        "The type of route. Note that 'local(3)' refers
-        to a route for which the next hop is the final
-        destination; 'remote(4)' refers to a route for
-        which  the  next  hop is not the final
-        destination; 'discard(2)' refers to a route
-        indicating that packets to destinations matching
-        this route are to be discarded (sometimes called
-        black-hole route)."
-     ::= { ipv6RouteEntry 6 }
-
- ipv6RouteProtocol OBJECT-TYPE
-     SYNTAX     INTEGER {
-       other(1),   -- none of the following
-
-                   -- non-protocol information,
-                   -- e.g., manually configured
-       local(2),   -- entries
-
-       netmgmt(3), -- static route
-
-                   -- obtained via Neighbor
-                   -- Discovery protocol,
-       ndisc(4),   -- e.g., result of Redirect
-
-                   -- the following are all
-                   -- dynamic routing protocols
-       rip(5),     -- RIPng
-       ospf(6),    -- Open Shortest Path First
-       bgp(7),     -- Border Gateway Protocol
-       idrp(8),    -- InterDomain Routing Protocol
-       igrp(9)     -- InterGateway Routing Protocol
-     }
-     MAX-ACCESS read-only
-     STATUS     current
-     DESCRIPTION
-       "The routing mechanism via which this route was
-       learned."
-     ::= { ipv6RouteEntry 7 }
-
- ipv6RoutePolicy OBJECT-TYPE
-     SYNTAX     Integer32
-     MAX-ACCESS read-only
-     STATUS     current
-     DESCRIPTION
-      "The general set of conditions that would cause the
-      selection of one multipath route (set of next hops
-      for a given destination) is referred to as 'policy'.
-      Unless the mechanism indicated by ipv6RouteProtocol
-      specified otherwise, the policy specifier is the
-      8-bit Traffic Class field of the IPv6 packet header
-      that is zero extended at the left to a 32-bit value.
-
-      Protocols defining 'policy' otherwise must either
-      define a set of values which are valid for
-      this object or must implement an integer-
-      instanced  policy table for which this object's
-      value acts as an index."
-     ::= { ipv6RouteEntry 8 }
-
- ipv6RouteAge OBJECT-TYPE
-     SYNTAX     Unsigned32
-     UNITS      "seconds"
-     MAX-ACCESS read-only
-     STATUS     current
-     DESCRIPTION
-        "The number of seconds since this route was last
-        updated or otherwise determined to be correct.
-        Note that no semantics of `too old' can be implied
-        except through knowledge of the routing protocol
-        by which the route was learned."
-     ::= { ipv6RouteEntry 9 }
-
- ipv6RouteNextHopRDI OBJECT-TYPE
-     SYNTAX     Unsigned32
-     MAX-ACCESS read-only
-     STATUS     current
-     DESCRIPTION
-        "The Routing Domain ID of the Next Hop.
-        The  semantics of this object are determined by
-        the routing-protocol specified in  the  route's
-        ipv6RouteProtocol value.   When  this object is
-        unknown or not relevant its value should be set
-        to zero."
-     ::= { ipv6RouteEntry 10 }
-
- ipv6RouteMetric OBJECT-TYPE
-     SYNTAX     Unsigned32
-     MAX-ACCESS read-only
-     STATUS     current
-     DESCRIPTION
-        "The routing metric for this route. The
-        semantics of this metric are determined by the
-        routing protocol specified in the route's
-        ipv6RouteProtocol value.  When this is unknown
-        or not relevant to the protocol indicated by
-        ipv6RouteProtocol, the object value should be
-        set to its maximum value (4,294,967,295)."
-     ::= { ipv6RouteEntry 11 }
-
- ipv6RouteWeight OBJECT-TYPE
-     SYNTAX     Unsigned32
-     MAX-ACCESS read-only
-     STATUS     current
-     DESCRIPTION
-        "The system internal weight value for this route.
-        The semantics of this value are determined by
-        the implementation specific rules. Generally,
-        within routes with the same ipv6RoutePolicy value,
-        the lower the weight value the more preferred is
-        the route."
-     ::= { ipv6RouteEntry 12 }
-
- ipv6RouteInfo OBJECT-TYPE
-     SYNTAX     RowPointer
-     MAX-ACCESS read-only
-     STATUS     current
-     DESCRIPTION
-        "A reference to MIB definitions specific to the
-        particular routing protocol which is responsible
-        for this route, as determined by the  value
-        specified  in the route's ipv6RouteProto value.
-        If this information is not present,  its  value
-        should be set to the OBJECT ID { 0 0 },
-        which is a syntactically valid object  identifier,
-        and any implementation conforming to ASN.1
-        and the Basic Encoding Rules must  be  able  to
-        generate and recognize this value."
-     ::= { ipv6RouteEntry 13 }
-
- ipv6RouteValid OBJECT-TYPE
-     SYNTAX     TruthValue
-     MAX-ACCESS read-write
-     STATUS     current
-     DESCRIPTION
-        "Setting this object to the value 'false(2)' has
-        the effect of invalidating the corresponding entry
-        in the ipv6RouteTable object.  That is, it
-        effectively disassociates the destination
-
-        identified with said entry from the route
-        identified with said entry.  It is an
-        implementation-specific matter as to whether the
-        agent removes an invalidated entry from the table.
-        Accordingly, management stations must be prepared
-        to receive tabular information from agents that
-        corresponds to entries not currently in use.
-        Proper interpretation of such entries requires
-        examination of the relevant ipv6RouteValid
-        object."
-     DEFVAL  { true }
-     ::= { ipv6RouteEntry 14 }
-
- -- IPv6 Address Translation table
-
- ipv6NetToMediaTable OBJECT-TYPE
-     SYNTAX      SEQUENCE OF Ipv6NetToMediaEntry
-     MAX-ACCESS  not-accessible
-     STATUS      current
-     DESCRIPTION
-       "The IPv6 Address Translation table used for
-       mapping from IPv6 addresses to physical addresses.
-
-       The IPv6 address translation table contain the
-       Ipv6Address to `physical' address equivalencies.
-       Some interfaces do not use translation tables
-       for determining address equivalencies; if all
-       interfaces are of this type, then the Address
-       Translation table is empty, i.e., has zero
-       entries."
-     ::= { ipv6MIBObjects 12 }
-
- ipv6NetToMediaEntry OBJECT-TYPE
-     SYNTAX     Ipv6NetToMediaEntry
-     MAX-ACCESS not-accessible
-     STATUS     current
-     DESCRIPTION
-       "Each entry contains one IPv6 address to `physical'
-       address equivalence."
-     INDEX   { ipv6IfIndex,
-               ipv6NetToMediaNetAddress }
-     ::= { ipv6NetToMediaTable 1 }
-
- Ipv6NetToMediaEntry ::= SEQUENCE {
-         ipv6NetToMediaNetAddress
-             Ipv6Address,
-         ipv6NetToMediaPhysAddress
-
-             PhysAddress,
-         ipv6NetToMediaType
-             INTEGER,
-         ipv6IfNetToMediaState
-             INTEGER,
-         ipv6IfNetToMediaLastUpdated
-             TimeStamp,
-         ipv6NetToMediaValid
-             TruthValue
-     }
-
- ipv6NetToMediaNetAddress OBJECT-TYPE
-     SYNTAX     Ipv6Address
-     MAX-ACCESS not-accessible
-     STATUS     current
-     DESCRIPTION
-        "The IPv6 Address corresponding to
-        the media-dependent `physical' address."
-     ::= { ipv6NetToMediaEntry 1 }
-
- ipv6NetToMediaPhysAddress OBJECT-TYPE
-     SYNTAX     PhysAddress
-     MAX-ACCESS read-only
-     STATUS     current
-     DESCRIPTION
-       "The media-dependent `physical' address."
-     ::= { ipv6NetToMediaEntry 2 }
-
- ipv6NetToMediaType OBJECT-TYPE
-     SYNTAX     INTEGER {
-                 other(1),    -- none of the following
-                 dynamic(2),  -- dynamically resolved
-                 static(3),   -- statically configured
-                 local(4)     -- local interface
-                }
-     MAX-ACCESS read-only
-     STATUS     current
-     DESCRIPTION
-             "The type of the mapping. The 'dynamic(2)' type
-             indicates that the IPv6 address to physical
-             addresses mapping has been dynamically
-             resolved using the IPv6 Neighbor Discovery
-             protocol. The static(3)' types indicates that
-             the mapping has been statically configured.
-             The local(4) indicates that the mapping is
-             provided for an entity's own interface address."
-     ::= { ipv6NetToMediaEntry 3 }
-
-ipv6IfNetToMediaState OBJECT-TYPE
-    SYNTAX      INTEGER {
-             reachable(1), -- confirmed reachability
-
-             stale(2),     -- unconfirmed reachability
-
-             delay(3),     -- waiting for reachability
-                           -- confirmation before entering
-                           -- the probe state
-
-             probe(4),     -- actively probing
-
-             invalid(5),   -- an invalidated mapping
-
-             unknown(6)    -- state can not be determined
-                           -- for some reason.
-            }
-    MAX-ACCESS  read-only
-    STATUS      current
-    DESCRIPTION
-        "The Neighbor Unreachability Detection [8] state
-        for the interface when the address mapping in
-        this entry is used."
-    ::= { ipv6NetToMediaEntry 4 }
-
-ipv6IfNetToMediaLastUpdated OBJECT-TYPE
-    SYNTAX      TimeStamp
-    MAX-ACCESS  read-only
-    STATUS      current
-    DESCRIPTION
-        "The value of sysUpTime at the time this entry
-        was last updated.  If this entry was updated prior
-        to the last re-initialization of the local network
-        management subsystem, then this object contains
-        a zero value."
-    ::= { ipv6NetToMediaEntry 5 }
-
- ipv6NetToMediaValid OBJECT-TYPE
-     SYNTAX     TruthValue
-     MAX-ACCESS read-write
-     STATUS     current
-     DESCRIPTION
-      "Setting this object to the value 'false(2)' has
-      the effect of invalidating the corresponding entry
-      in the ipv6NetToMediaTable.  That is, it effectively
-      disassociates the interface identified with said
-      entry from the mapping identified with said entry.
-      It is an implementation-specific matter as to
-
-      whether the agent removes an invalidated entry
-      from the table.  Accordingly, management stations
-      must be prepared to receive tabular information
-      from agents that corresponds to entries not
-      currently in use.  Proper interpretation of such
-      entries requires examination of the relevant
-      ipv6NetToMediaValid object."
-     DEFVAL  { true }
-     ::= { ipv6NetToMediaEntry 6 }
-
--- definition of IPv6-related notifications.
--- Note that we need ipv6NotificationPrefix with the 0
--- sub-identifier to make this MIB to translate to
--- an SNMPv1 format in a reversible way. For example
--- it is needed for proxies that convert SNMPv1 traps
--- to SNMPv2 notifications without MIB knowledge.
-
-ipv6Notifications      OBJECT IDENTIFIER
-     ::= { ipv6MIB 2 }
-ipv6NotificationPrefix OBJECT IDENTIFIER
-     ::= { ipv6Notifications 0 }
-
-ipv6IfStateChange NOTIFICATION-TYPE
-     OBJECTS {
-              ipv6IfDescr,
-              ipv6IfOperStatus -- the new state of the If.
-             }
-     STATUS             current
-     DESCRIPTION
-        "An ipv6IfStateChange notification signifies
-        that there has been a change in the state of
-        an ipv6 interface.  This notification should
-        be generated when the interface's operational
-        status transitions to or from the up(1) state."
-     ::= { ipv6NotificationPrefix 1 }
-
--- conformance information
-
-ipv6Conformance OBJECT IDENTIFIER ::= { ipv6MIB 3 }
-
-ipv6Compliances OBJECT IDENTIFIER ::= { ipv6Conformance 1 }
-ipv6Groups      OBJECT IDENTIFIER ::= { ipv6Conformance 2 }
-
--- compliance statements
-
-ipv6Compliance MODULE-COMPLIANCE
-    STATUS  current
-    DESCRIPTION
-      "The compliance statement for SNMPv2 entities which
-      implement ipv6 MIB."
-    MODULE  -- this module
-        MANDATORY-GROUPS { ipv6GeneralGroup,
-                           ipv6NotificationGroup }
-          OBJECT    ipv6Forwarding
-            MIN-ACCESS  read-only
-            DESCRIPTION
-               "An agent is not required to provide write
-                access to this object"
-          OBJECT    ipv6DefaultHopLimit
-            MIN-ACCESS  read-only
-            DESCRIPTION
-               "An agent is not required to provide write
-                access to this object"
-          OBJECT    ipv6IfDescr
-            MIN-ACCESS  read-only
-            DESCRIPTION
-               "An agent is not required to provide write
-                access to this object"
-          OBJECT    ipv6IfIdentifier
-            MIN-ACCESS  read-only
-            DESCRIPTION
-               "An agent is not required to provide write
-                access to this object"
-          OBJECT    ipv6IfIdentifierLength
-            MIN-ACCESS  read-only
-            DESCRIPTION
-               "An agent is not required to provide write
-                access to this object"
-
-          OBJECT    ipv6IfAdminStatus
-            MIN-ACCESS  read-only
-            DESCRIPTION
-               "An agent is not required to provide write
-                access to this object"
-          OBJECT    ipv6RouteValid
-            MIN-ACCESS  read-only
-            DESCRIPTION
-               "An agent is not required to provide write
-                access to this object"
-          OBJECT    ipv6NetToMediaValid
-            MIN-ACCESS  read-only
-            DESCRIPTION
-               "An agent is not required to provide write
-
-                access to this object"
-    ::= { ipv6Compliances 1 }
-
-ipv6GeneralGroup OBJECT-GROUP
-    OBJECTS { ipv6Forwarding,
-              ipv6DefaultHopLimit,
-              ipv6Interfaces,
-              ipv6IfTableLastChange,
-              ipv6IfDescr,
-              ipv6IfLowerLayer,
-              ipv6IfEffectiveMtu,
-              ipv6IfReasmMaxSize,
-              ipv6IfIdentifier,
-              ipv6IfIdentifierLength,
-              ipv6IfPhysicalAddress,
-              ipv6IfAdminStatus,
-              ipv6IfOperStatus,
-              ipv6IfLastChange,
-              ipv6IfStatsInReceives,
-              ipv6IfStatsInHdrErrors,
-              ipv6IfStatsInTooBigErrors,
-              ipv6IfStatsInNoRoutes,
-              ipv6IfStatsInAddrErrors,
-              ipv6IfStatsInUnknownProtos,
-              ipv6IfStatsInTruncatedPkts,
-              ipv6IfStatsInDiscards,
-              ipv6IfStatsInDelivers,
-              ipv6IfStatsOutForwDatagrams,
-              ipv6IfStatsOutRequests,
-              ipv6IfStatsOutDiscards,
-              ipv6IfStatsOutFragOKs,
-              ipv6IfStatsOutFragFails,
-              ipv6IfStatsOutFragCreates,
-              ipv6IfStatsReasmReqds,
-              ipv6IfStatsReasmOKs,
-              ipv6IfStatsReasmFails,
-              ipv6IfStatsInMcastPkts,
-              ipv6IfStatsOutMcastPkts,
-              ipv6AddrPrefixOnLinkFlag,
-              ipv6AddrPrefixAutonomousFlag,
-              ipv6AddrPrefixAdvPreferredLifetime,
-              ipv6AddrPrefixAdvValidLifetime,
-              ipv6AddrPfxLength,
-              ipv6AddrType,
-              ipv6AddrAnycastFlag,
-              ipv6AddrStatus,
-              ipv6RouteNumber,
-              ipv6DiscardedRoutes,
-              ipv6RouteIfIndex,
-              ipv6RouteNextHop,
-              ipv6RouteType,
-              ipv6RouteProtocol,
-              ipv6RoutePolicy,
-              ipv6RouteAge,
-              ipv6RouteNextHopRDI,
-              ipv6RouteMetric,
-              ipv6RouteWeight,
-              ipv6RouteInfo,
-              ipv6RouteValid,
-              ipv6NetToMediaPhysAddress,
-              ipv6NetToMediaType,
-              ipv6IfNetToMediaState,
-              ipv6IfNetToMediaLastUpdated,
-              ipv6NetToMediaValid }
-    STATUS    current
-    DESCRIPTION
-         "The IPv6 group of objects providing for basic
-          management of IPv6 entities."
-    ::= { ipv6Groups 1 }
-
-ipv6NotificationGroup NOTIFICATION-GROUP
-    NOTIFICATIONS { ipv6IfStateChange }
-    STATUS    current
-    DESCRIPTION
-         "The notification that an IPv6 entity is required
-          to implement."
-    ::= { ipv6Groups 2 }
-
- END