console-server: T2490: initial support

1 files changed, 78 insertions, 0 deletions

diff --git a/data/templates/ser2net/ser2net.conf.tmpl b/data/templates/ser2net/ser2net.conf.tmpl
new file mode 100644
index 000000000..202fe8104
--- /dev/null
+++ b/data/templates/ser2net/ser2net.conf.tmpl
@@ -0,0 +1,78 @@
+### Autogenerated by ser2net.py ###
+
+# This is the configuration file for ser2net.  It has the following format:
+#  <TCP port>:<state>:<timeout>:<device>:<options>
+#     TCP port
+#            Name   or  number of the TCP/IP port to accept con-
+#            nections from for this device.  A port number may
+#            be of the form [host,]port, such as 127.0.0.1,2000
+#            or localhost,2000.  If this is specified, it will
+#            only bind to the IP address specified. Otherwise
+#            it will bind to all the ports on the machine.
+#
+#     state  Either raw or rawlp or telnet or off.  off disables
+#            the  port  from  accepting  connections.  It can be
+#            turned on later from the control port.  raw enables
+#            the port and  transfers  all data as-is between the
+#            port  and  the long.  rawlp  enables  the port  and
+#            transfers  all input data to device, device is open
+#            without  any  termios  setting.  It  allow  to  use
+#            /dev/lpX  devices  and  printers connected to them.
+#            telnet enables the port and runs the telnet  proto-
+#            col  on the port to set up telnet parameters.  This
+#            is most useful for using telnet.
+#
+#     timeout
+#            The time (in seconds) before the port will be  dis-
+#            connected  if  there  is no activity on it.  A zero
+#            value disables this funciton.
+#
+#     device The  name  of  the  device   to  connect  to.  This
+#            must be in the form of /dev/<device>.
+#
+#     options
+#            Sets  operational  parameters  for the serial port.
+#            Options 300, 1200, 2400, 4800, 9600, 19200, 38400,
+#            57600, 115200 set the various baud rates.  EVEN,
+#            ODD, NONE set the parity.  1STOPBIT, 2STOPBITS set
+#            the number of stop bits.  7DATABITS, 8DATABITS set
+#            the number of data bits.  [-]XONXOFF turns on (-
+#            off) XON/XOFF support.  [-]RTSCTS turns on (- off)
+#            hardware flow control, [-]LOCAL turns off (- on)
+#            monitoring of the modem lines, and
+#            [-]HANGUP_WHEN_DONE turns on (- off) lowering the
+#            modem control lines when the connextion is done.
+#            NOBREAK disables automatic setting of the break
+#            setting of the serial port.
+#            The "remctl" option allow remote control (ala RFC
+#            2217) of serial-port configuration.  A banner name
+#            may also be specified, that banner will be printed
+#            for the line.  If no banner is given, then no
+#            banner is printed.
+#
+# or...
+
+#  BANNER:<banner name>:banner
+#    This will create a banner, if the banner name is given in the
+#    options of a line, that banner will be printed.  This takes the
+#    standard "C" \x characters (\r is carraige return, \n is newline,
+#    etc.).  It also accepts \d, which prints the device name, \p,
+#    which prints the TCP port number, and \s which prints the serial
+#    parameters (eg 9600N81).  Banners can span lines if the last
+#    character on a line is '\'.  Note that you *must* use \r\n to
+#    start a new line.
+#
+# Note that the same device can be listed multiple times under different
+# ports, this allows the same serial port to have both telnet and raw
+# protocols.
+
+# The original config file shipped with the upstream sources can be
+# found in /usr/share/doc/ser2net/examples
+
+BANNER:banner:\r\nser2net port \p device \d [\s] (VyOS)\r\n\r\n
+
+#3001:telnet:600:/dev/ttyS1:19200 8DATABITS NONE 1STOPBIT banner
+
+{% for d in devices %}
+localhost,{{ d.port }}:telnet:{{ d.timeout }}:{{ d.serial_port }}:{{ d.speed }} {{ d.data_bits}}DATABITS {{ d.parity | upper }} {{ d.stop_bits}}STOPBIT banner
+{% endfor %}