snmp: T3606: Install MIBs into well known location

FRR also expects the MIBs in /usr/share/snmp/mibs

1 files changed, 1882 insertions, 0 deletions

diff --git a/mibs/DISMAN-EVENT-MIB.txt b/mibs/DISMAN-EVENT-MIB.txt
new file mode 100644
index 000000000..f00c7cc89
--- /dev/null
+++ b/mibs/DISMAN-EVENT-MIB.txt
@@ -0,0 +1,1882 @@
+DISMAN-EVENT-MIB DEFINITIONS ::= BEGIN
+
+IMPORTS
+    MODULE-IDENTITY, OBJECT-TYPE,
+    Integer32, Unsigned32,
+    NOTIFICATION-TYPE, Counter32,
+    Gauge32, mib-2, zeroDotZero         FROM SNMPv2-SMI
+    TEXTUAL-CONVENTION, RowStatus,
+    TruthValue                FROM SNMPv2-TC
+
+    MODULE-COMPLIANCE, OBJECT-GROUP,
+    NOTIFICATION-GROUP             FROM SNMPv2-CONF
+    sysUpTime                 FROM SNMPv2-MIB
+    SnmpTagValue              FROM SNMP-TARGET-MIB
+    SnmpAdminString           FROM SNMP-FRAMEWORK-MIB;
+
+dismanEventMIB MODULE-IDENTITY
+    LAST-UPDATED "200010160000Z"            -- 16 October 2000
+    ORGANIZATION "IETF Distributed Management Working Group"
+    CONTACT-INFO "Ramanathan Kavasseri
+                  Cisco Systems, Inc.
+                  170 West Tasman Drive,
+                  San Jose CA 95134-1706.
+                  Phone: +1 408 526 4527
+                  Email: ramk@cisco.com"
+    DESCRIPTION
+     "The MIB module for defining event triggers and actions
+     for network management purposes."
+-- Revision History
+
+       REVISION     "200010160000Z"            -- 16 October 2000
+       DESCRIPTION  "This is the initial version of this MIB.
+                    Published as RFC 2981"
+    ::= { mib-2 88 }
+
+dismanEventMIBObjects OBJECT IDENTIFIER ::= { dismanEventMIB 1 }
+
+-- Management Triggered Event (MTE) objects
+
+mteResource           OBJECT IDENTIFIER ::= { dismanEventMIBObjects 1 }
+mteTrigger            OBJECT IDENTIFIER ::= { dismanEventMIBObjects 2 }
+mteObjects            OBJECT IDENTIFIER ::= { dismanEventMIBObjects 3 }
+mteEvent              OBJECT IDENTIFIER ::= { dismanEventMIBObjects 4 }
+
+--
+-- Textual Conventions
+--
+
+FailureReason ::= TEXTUAL-CONVENTION
+    STATUS      current
+    DESCRIPTION
+        "Reasons for failures in an attempt to perform a management
+        request.
+
+        The first group of errors, numbered less than 0, are related
+        to problems in sending the request.  The existence of a
+        particular error code here does not imply that all
+        implementations are capable of sensing that error and
+
+        returning that code.
+
+        The second group, numbered greater than 0, are copied
+        directly from SNMP protocol operations and are intended to
+        carry exactly the meanings defined for the protocol as returned
+        in an SNMP response.
+
+        localResourceLack       some local resource such as memory
+                                lacking or
+                                mteResourceSampleInstanceMaximum
+                                exceeded
+        badDestination          unrecognized domain name or otherwise
+                                invalid destination address
+        destinationUnreachable  can't get to destination address
+        noResponse              no response to SNMP request
+        badType                 the data syntax of a retrieved object
+                                as not as expected
+        sampleOverrun           another sample attempt occurred before
+                                the previous one completed"
+    SYNTAX      INTEGER { localResourceLack(-1),
+                          badDestination(-2),
+                          destinationUnreachable(-3),
+                          noResponse(-4),
+                          badType(-5),
+                          sampleOverrun(-6),
+                          noError(0),
+                          tooBig(1),
+                          noSuchName(2),
+                          badValue(3),
+                          readOnly(4),
+                          genErr(5),
+                          noAccess(6),
+                          wrongType(7),
+                          wrongLength(8),
+                          wrongEncoding(9),
+                          wrongValue(10),
+                          noCreation(11),
+                          inconsistentValue(12),
+                          resourceUnavailable(13),
+                          commitFailed(14),
+                          undoFailed(15),
+                          authorizationError(16),
+                          notWritable(17),
+                          inconsistentName(18) }
+--
+
+-- Resource Control Section
+--
+
+mteResourceSampleMinimum OBJECT-TYPE
+    SYNTAX      Integer32 (1..2147483647)
+    UNITS       "seconds"
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The minimum mteTriggerFrequency this system will
+        accept.  A system may use the larger values of this minimum to
+        lessen the impact of constant sampling.  For larger
+        sampling intervals the system samples less often and
+        suffers less overhead.  This object provides a way to enforce
+        such lower overhead for all triggers created after it is
+        set.
+
+        Unless explicitly resource limited, a system's value for
+        this object SHOULD be 1, allowing as small as a 1 second
+        interval for ongoing trigger sampling.
+
+        Changing this value will not invalidate an existing setting
+        of mteTriggerFrequency."
+    ::= { mteResource 1 }
+
+mteResourceSampleInstanceMaximum OBJECT-TYPE
+    SYNTAX      Unsigned32
+    UNITS       "instances"
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The maximum number of instance entries this system will
+        support for sampling.
+
+        These are the entries that maintain state, one for each
+        instance of each sampled object as selected by
+        mteTriggerValueID.  Note that wildcarded objects result
+        in multiple instances of this state.
+
+        A value of 0 indicates no preset limit, that is, the limit
+        is dynamic based on system operation and resources.
+
+        Unless explicitly resource limited, a system's value for
+        this object SHOULD be 0.
+
+        Changing this value will not eliminate or inhibit existing
+        sample state but could prevent allocation of additional state
+        information."
+    ::= { mteResource 2 }
+
+mteResourceSampleInstances OBJECT-TYPE
+    SYNTAX      Gauge32
+    UNITS       "instances"
+    MAX-ACCESS  read-only
+    STATUS      current
+    DESCRIPTION
+        "The number of currently active instance entries as
+        defined for mteResourceSampleInstanceMaximum."
+    ::= { mteResource 3 }
+
+mteResourceSampleInstancesHigh OBJECT-TYPE
+    SYNTAX      Gauge32
+    UNITS       "instances"
+    MAX-ACCESS  read-only
+    STATUS      current
+    DESCRIPTION
+        "The highest value of mteResourceSampleInstances that has
+        occurred since initialization of the management system."
+    ::= { mteResource 4 }
+
+mteResourceSampleInstanceLacks OBJECT-TYPE
+    SYNTAX      Counter32
+    UNITS       "instances"
+    MAX-ACCESS  read-only
+    STATUS      current
+    DESCRIPTION
+        "The number of times this system could not take a new sample
+        because that allocation would have exceeded the limit set by
+        mteResourceSampleInstanceMaximum."
+    ::= { mteResource 5 }
+
+--
+-- Trigger Section
+--
+
+-- Counters
+
+mteTriggerFailures OBJECT-TYPE
+    SYNTAX      Counter32
+    UNITS       "failures"
+    MAX-ACCESS  read-only
+    STATUS      current
+    DESCRIPTION
+        "The number of times an attempt to check for a trigger
+        condition has failed.  This counts individually for each
+        attempt in a group of targets or each attempt for a
+
+        wildcarded object."
+    ::= { mteTrigger 1 }
+
+--
+-- Trigger Table
+--
+
+mteTriggerTable OBJECT-TYPE
+    SYNTAX      SEQUENCE OF MteTriggerEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "A table of management event trigger information."
+    ::= { mteTrigger 2 }
+
+mteTriggerEntry OBJECT-TYPE
+    SYNTAX      MteTriggerEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "Information about a single trigger.  Applications create and
+        delete entries using mteTriggerEntryStatus."
+    INDEX       { mteOwner, IMPLIED mteTriggerName }
+    ::= { mteTriggerTable 1 }
+
+MteTriggerEntry ::= SEQUENCE {
+    mteOwner                            SnmpAdminString,
+    mteTriggerName                      SnmpAdminString,
+    mteTriggerComment                   SnmpAdminString,
+    mteTriggerTest                      BITS,
+    mteTriggerSampleType                INTEGER,
+    mteTriggerValueID                   OBJECT IDENTIFIER,
+    mteTriggerValueIDWildcard           TruthValue,
+    mteTriggerTargetTag                 SnmpTagValue,
+    mteTriggerContextName               SnmpAdminString,
+    mteTriggerContextNameWildcard       TruthValue,
+    mteTriggerFrequency                 Unsigned32,
+    mteTriggerObjectsOwner              SnmpAdminString,
+    mteTriggerObjects                   SnmpAdminString,
+    mteTriggerEnabled                   TruthValue,
+    mteTriggerEntryStatus               RowStatus
+}
+
+mteOwner OBJECT-TYPE
+   SYNTAX      SnmpAdminString (SIZE(0..32))
+   MAX-ACCESS  not-accessible
+   STATUS      current
+   DESCRIPTION
+        "The owner of this entry. The exact semantics of this
+        string are subject to the security policy defined by the
+        security administrator."
+    ::= { mteTriggerEntry 1 }
+
+mteTriggerName OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (1..32))
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "A locally-unique, administratively assigned name for the
+        trigger within the scope of mteOwner."
+    ::= { mteTriggerEntry 2 }
+
+mteTriggerComment OBJECT-TYPE
+    SYNTAX      SnmpAdminString
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "A description of the trigger's function and use."
+    DEFVAL { ''H }
+    ::= { mteTriggerEntry 3 }
+
+mteTriggerTest OBJECT-TYPE
+    SYNTAX      BITS { existence(0), boolean(1), threshold(2) }
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "The type of trigger test to perform.  For 'boolean' and
+        'threshold'  tests, the object at mteTriggerValueID MUST
+        evaluate to an integer, that is, anything that ends up encoded
+        for transmission (that is, in BER, not ASN.1) as an integer.
+
+        For 'existence', the specific test is as selected by
+        mteTriggerExistenceTest.  When an object appears, vanishes
+        or changes value, the trigger fires. If the object's
+        appearance caused the trigger firing, the object MUST
+        vanish before the trigger can be fired again for it, and
+        vice versa. If the trigger fired due to a change in the
+        object's value, it will be fired again on every successive
+        value change for that object.
+
+        For 'boolean', the specific test is as selected by
+        mteTriggerBooleanTest.  If the test result is true the trigger
+        fires.  The trigger will not fire again until the value has
+        become false and come back to true.
+
+        For 'threshold' the test works as described below for
+
+        mteTriggerThresholdStartup, mteTriggerThresholdRising, and
+        mteTriggerThresholdFalling.
+
+        Note that combining 'boolean' and 'threshold' tests on the
+        same object may be somewhat redundant."
+    DEFVAL { { boolean } }
+    ::= { mteTriggerEntry 4 }
+
+mteTriggerSampleType OBJECT-TYPE
+    SYNTAX      INTEGER { absoluteValue(1), deltaValue(2) }
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "The type of sampling to perform.
+
+        An 'absoluteValue' sample requires only a single sample to be
+        meaningful, and is exactly the value of the object at
+        mteTriggerValueID at the sample time.
+
+        A 'deltaValue' requires two samples to be meaningful and is
+        thus not available for testing until the second and subsequent
+        samples after the object at mteTriggerValueID is first found
+        to exist.  It is the difference between the two samples.  For
+        unsigned values it is always positive, based on unsigned
+        arithmetic.  For signed values it can be positive or negative.
+
+        For SNMP counters to be meaningful they should be sampled as a
+        'deltaValue'.
+
+        For 'deltaValue' mteTriggerDeltaTable contains further
+        parameters.
+
+        If only 'existence' is set in mteTriggerTest this object has
+        no meaning."
+    DEFVAL { absoluteValue }
+    ::= { mteTriggerEntry 5 }
+
+mteTriggerValueID OBJECT-TYPE
+    SYNTAX      OBJECT IDENTIFIER
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "The object identifier of the MIB object to sample to see
+        if the trigger should fire.
+
+        This may be wildcarded by truncating all or part of the
+        instance portion, in which case the value is obtained
+        as if with a GetNext function, checking multiple values
+
+        if they exist.  If such wildcarding is applied,
+        mteTriggerValueIDWildcard must be 'true' and if not it must
+        be 'false'.
+
+        Bad object identifiers or a mismatch between truncating the
+        identifier and the value of mteTriggerValueIDWildcard result
+        in operation as one would expect when providing the wrong
+        identifier to a Get or GetNext operation.  The Get will fail
+        or get the wrong object.  The GetNext will indeed get whatever
+        is next, proceeding until it runs past the initial part of the
+        identifier and perhaps many unintended objects for confusing
+        results.  If the value syntax of those objects is not usable,
+        that results in a 'badType' error that terminates the scan.
+
+        Each instance that fills the wildcard is independent of any
+        additional instances, that is, wildcarded objects operate
+        as if there were a separate table entry for each instance
+        that fills the wildcard without having to actually predict
+        all possible instances ahead of time."
+    DEFVAL { zeroDotZero }
+    ::= { mteTriggerEntry 6 }
+
+mteTriggerValueIDWildcard OBJECT-TYPE
+    SYNTAX      TruthValue
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "Control for whether mteTriggerValueID is to be treated as
+        fully-specified or wildcarded, with 'true' indicating wildcard."
+    DEFVAL { false }
+    ::= { mteTriggerEntry 7 }
+
+mteTriggerTargetTag OBJECT-TYPE
+    SYNTAX      SnmpTagValue
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "The tag for the target(s) from which to obtain the condition
+        for a trigger check.
+
+        A length of 0 indicates the local system.  In this case,
+        access to the objects indicated by mteTriggerValueID is under
+        the security credentials of the requester that set
+        mteTriggerEntryStatus to 'active'.  Those credentials are the
+        input parameters for isAccessAllowed from the Architecture for
+        Describing SNMP Management Frameworks.
+
+        Otherwise access rights are checked according to the security
+
+        parameters resulting from the tag."
+    DEFVAL { ''H }
+    ::= { mteTriggerEntry 8 }
+
+mteTriggerContextName OBJECT-TYPE
+    SYNTAX      SnmpAdminString
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "The management context from which to obtain mteTriggerValueID.
+
+        This may be wildcarded by leaving characters off the end.  For
+        example use 'Repeater' to wildcard to 'Repeater1',
+        'Repeater2', 'Repeater-999.87b', and so on.  To indicate such
+        wildcarding is intended, mteTriggerContextNameWildcard must
+        be 'true'.
+
+        Each instance that fills the wildcard is independent of any
+        additional instances, that is, wildcarded objects operate
+        as if there were a separate table entry for each instance
+        that fills the wildcard without having to actually predict
+        all possible instances ahead of time.
+
+        Operation of this feature assumes that the local system has a
+        list of available contexts against which to apply the
+        wildcard.  If the objects are being read from the local
+        system, this is clearly the system's own list of contexts.
+        For a remote system a local version of such a list is not
+        defined by any current standard and may not be available, so
+        this function MAY not be supported."
+    DEFVAL { ''H }
+    ::= { mteTriggerEntry 9 }
+
+mteTriggerContextNameWildcard OBJECT-TYPE
+    SYNTAX      TruthValue
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "Control for whether mteTriggerContextName is to be treated as
+        fully-specified or wildcarded, with 'true' indicating wildcard."
+    DEFVAL { false }
+    ::= { mteTriggerEntry 10 }
+
+mteTriggerFrequency OBJECT-TYPE
+    SYNTAX      Unsigned32
+    UNITS       "seconds"
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "The number of seconds to wait between trigger samples.  To
+        encourage consistency in sampling, the interval is measured
+        from the beginning of one check to the beginning of the next
+        and the timer is restarted immediately when it expires, not
+        when the check completes.
+
+        If the next sample begins before the previous one completed the
+        system may either attempt to make the check or treat this as an
+        error condition with the error 'sampleOverrun'.
+
+        A frequency of 0 indicates instantaneous recognition of the
+        condition.  This is not possible in many cases, but may
+        be supported in cases where it makes sense and the system is
+        able to do so.  This feature allows the MIB to be used in
+        implementations where such interrupt-driven behavior is
+        possible and is not likely to be supported for all MIB objects
+        even then since such sampling generally has to be tightly
+        integrated into low-level code.
+
+        Systems that can support this SHOULD document those cases
+        where it can be used.  In cases where it can not, setting this
+        object to 0 should be disallowed."
+    DEFVAL { 600 }
+    ::= { mteTriggerEntry 11 }
+
+mteTriggerObjectsOwner OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "To go with mteTriggerObjects, the mteOwner of a group of
+        objects from mteObjectsTable."
+    DEFVAL { ''H }
+    ::= { mteTriggerEntry 12 }
+
+mteTriggerObjects OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "The mteObjectsName of a group of objects from
+        mteObjectsTable.  These objects are to be added to any
+        Notification resulting from the firing of this trigger.
+
+        A list of objects may also be added based on the event or on
+        the value of mteTriggerTest.
+
+        A length of 0 indicates no additional objects."
+    DEFVAL { ''H }
+    ::= { mteTriggerEntry 13 }
+
+mteTriggerEnabled OBJECT-TYPE
+    SYNTAX      TruthValue
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "A control to allow a trigger to be configured but not used.
+        When the value is 'false' the trigger is not sampled."
+    DEFVAL { false }
+    ::= { mteTriggerEntry 14 }
+
+mteTriggerEntryStatus OBJECT-TYPE
+    SYNTAX      RowStatus
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "The control that allows creation and deletion of entries.
+        Once made active an entry may not be modified except to
+        delete it."
+    ::= { mteTriggerEntry 15 }
+
+--
+-- Trigger Delta Table
+--
+
+mteTriggerDeltaTable OBJECT-TYPE
+    SYNTAX      SEQUENCE OF MteTriggerDeltaEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "A table of management event trigger information for delta
+        sampling."
+    ::= { mteTrigger 3 }
+
+mteTriggerDeltaEntry OBJECT-TYPE
+    SYNTAX      MteTriggerDeltaEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "Information about a single trigger's delta sampling.  Entries
+        automatically exist in this this table for each mteTriggerEntry
+        that has mteTriggerSampleType set to 'deltaValue'."
+    INDEX       { mteOwner, IMPLIED mteTriggerName }
+    ::= { mteTriggerDeltaTable 1 }
+
+MteTriggerDeltaEntry ::= SEQUENCE {
+    mteTriggerDeltaDiscontinuityID                OBJECT IDENTIFIER,
+    mteTriggerDeltaDiscontinuityIDWildcard        TruthValue,
+    mteTriggerDeltaDiscontinuityIDType            INTEGER
+}
+
+sysUpTimeInstance OBJECT IDENTIFIER ::= { sysUpTime 0 }
+
+mteTriggerDeltaDiscontinuityID OBJECT-TYPE
+    SYNTAX      OBJECT IDENTIFIER
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The OBJECT IDENTIFIER (OID) of a TimeTicks, TimeStamp, or
+        DateAndTime object that indicates a discontinuity in the value
+        at mteTriggerValueID.
+
+        The OID may be for a leaf object (e.g. sysUpTime.0) or may
+        be wildcarded to match mteTriggerValueID.
+
+        This object supports normal checking for a discontinuity in a
+        counter.  Note that if this object does not point to sysUpTime
+        discontinuity checking MUST still check sysUpTime for an overall
+        discontinuity.
+
+        If the object identified is not accessible the sample attempt
+        is in error, with the error code as from an SNMP request.
+
+        Bad object identifiers or a mismatch between truncating the
+        identifier and the value of mteDeltaDiscontinuityIDWildcard
+        result in operation as one would expect when providing the
+        wrong identifier to a Get operation.  The Get will fail or get
+        the wrong object.  If the value syntax of those objects is not
+        usable, that results in an error that terminates the sample
+        with a 'badType' error code."
+    DEFVAL { sysUpTimeInstance }
+    ::= { mteTriggerDeltaEntry 1 }
+
+mteTriggerDeltaDiscontinuityIDWildcard OBJECT-TYPE
+     SYNTAX      TruthValue
+     MAX-ACCESS  read-write
+     STATUS      current
+     DESCRIPTION
+        "Control for whether mteTriggerDeltaDiscontinuityID is to be
+        treated as fully-specified or wildcarded, with 'true'
+        indicating wildcard. Note that the value of this object will
+        be the same as that of the corresponding instance of
+        mteTriggerValueIDWildcard when the corresponding
+
+        mteTriggerSampleType is 'deltaValue'."
+    DEFVAL { false }
+    ::= { mteTriggerDeltaEntry 2 }
+
+mteTriggerDeltaDiscontinuityIDType OBJECT-TYPE
+    SYNTAX      INTEGER { timeTicks(1), timeStamp(2), dateAndTime(3) }
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The value 'timeTicks' indicates the
+        mteTriggerDeltaDiscontinuityID of this row is of syntax
+        TimeTicks.  The value 'timeStamp' indicates syntax TimeStamp.
+        The value 'dateAndTime' indicates syntax DateAndTime."
+    DEFVAL { timeTicks }
+    ::= { mteTriggerDeltaEntry 3 }
+
+--
+-- Trigger Existence Table
+--
+
+mteTriggerExistenceTable OBJECT-TYPE
+    SYNTAX      SEQUENCE OF MteTriggerExistenceEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "A table of management event trigger information for existence
+        triggers."
+    ::= { mteTrigger 4 }
+
+mteTriggerExistenceEntry OBJECT-TYPE
+    SYNTAX      MteTriggerExistenceEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "Information about a single existence trigger.  Entries
+        automatically exist in this this table for each mteTriggerEntry
+        that has 'existence' set in mteTriggerTest."
+    INDEX       { mteOwner, IMPLIED mteTriggerName }
+    ::= { mteTriggerExistenceTable 1 }
+
+MteTriggerExistenceEntry ::= SEQUENCE {
+    mteTriggerExistenceTest              BITS,
+    mteTriggerExistenceStartup           BITS,
+    mteTriggerExistenceObjectsOwner      SnmpAdminString,
+    mteTriggerExistenceObjects           SnmpAdminString,
+    mteTriggerExistenceEventOwner        SnmpAdminString,
+    mteTriggerExistenceEvent             SnmpAdminString
+}
+
+mteTriggerExistenceTest OBJECT-TYPE
+    SYNTAX      BITS { present(0), absent(1), changed(2) }
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The type of existence test to perform.  The trigger fires
+        when the object at mteTriggerValueID is seen to go from
+        present to absent, from absent to present, or to have it's
+        value changed, depending on which tests are selected:
+
+        present(0) - when this test is selected, the trigger fires
+        when the mteTriggerValueID object goes from absent to present.
+
+        absent(1)  - when this test is selected, the trigger fires
+        when the mteTriggerValueID object goes from present to absent.
+        changed(2) - when this test is selected, the trigger fires
+        the mteTriggerValueID object value changes.
+
+        Once the trigger has fired for either presence or absence it
+        will not fire again for that state until the object has been
+        to the other state. "
+    DEFVAL { { present, absent } }
+    ::= { mteTriggerExistenceEntry 1 }
+
+mteTriggerExistenceStartup OBJECT-TYPE
+    SYNTAX      BITS { present(0), absent(1) }
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "Control for whether an event may be triggered when this entry
+        is first set to 'active' and the test specified by
+        mteTriggerExistenceTest is true.  Setting an option causes
+        that trigger to fire when its test is true."
+    DEFVAL { { present, absent } }
+    ::= { mteTriggerExistenceEntry 2 }
+
+mteTriggerExistenceObjectsOwner OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "To go with mteTriggerExistenceObjects, the mteOwner of a
+        group of objects from mteObjectsTable."
+    DEFVAL { ''H }
+    ::= { mteTriggerExistenceEntry 3 }
+
+mteTriggerExistenceObjects OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The mteObjectsName of a group of objects from
+        mteObjectsTable.  These objects are to be added to any
+        Notification resulting from the firing of this trigger for
+        this test.
+
+        A list of objects may also be added based on the overall
+        trigger, the event or other settings in mteTriggerTest.
+
+        A length of 0 indicates no additional objects."
+    DEFVAL { ''H }
+    ::= { mteTriggerExistenceEntry 4 }
+
+mteTriggerExistenceEventOwner OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "To go with mteTriggerExistenceEvent, the mteOwner of an event
+        entry from the mteEventTable."
+    DEFVAL { ''H }
+    ::= { mteTriggerExistenceEntry 5 }
+
+mteTriggerExistenceEvent OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The mteEventName of the event to invoke when mteTriggerType is
+        'existence' and this trigger fires.  A length of 0 indicates no
+        event."
+    DEFVAL { ''H }
+    ::= { mteTriggerExistenceEntry 6 }
+
+--
+-- Trigger Boolean Table
+--
+
+mteTriggerBooleanTable OBJECT-TYPE
+    SYNTAX      SEQUENCE OF MteTriggerBooleanEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "A table of management event trigger information for boolean
+        triggers."
+    ::= { mteTrigger 5 }
+
+mteTriggerBooleanEntry OBJECT-TYPE
+    SYNTAX      MteTriggerBooleanEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "Information about a single boolean trigger.  Entries
+        automatically exist in this this table for each mteTriggerEntry
+        that has 'boolean' set in mteTriggerTest."
+    INDEX       { mteOwner, IMPLIED mteTriggerName }
+    ::= { mteTriggerBooleanTable 1 }
+
+MteTriggerBooleanEntry ::= SEQUENCE {
+    mteTriggerBooleanComparison          INTEGER,
+    mteTriggerBooleanValue               Integer32,
+    mteTriggerBooleanStartup             TruthValue,
+    mteTriggerBooleanObjectsOwner        SnmpAdminString,
+    mteTriggerBooleanObjects             SnmpAdminString,
+    mteTriggerBooleanEventOwner          SnmpAdminString,
+    mteTriggerBooleanEvent               SnmpAdminString
+}
+
+mteTriggerBooleanComparison OBJECT-TYPE
+    SYNTAX      INTEGER { unequal(1), equal(2),
+                 less(3), lessOrEqual(4),
+                 greater(5), greaterOrEqual(6) }
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The type of boolean comparison to perform.
+
+        The value at mteTriggerValueID is compared to
+        mteTriggerBooleanValue, so for example if
+        mteTriggerBooleanComparison is 'less' the result would be true
+        if the value at mteTriggerValueID is less than the value of
+        mteTriggerBooleanValue."
+    DEFVAL { unequal }
+    ::= { mteTriggerBooleanEntry 1 }
+
+mteTriggerBooleanValue OBJECT-TYPE
+    SYNTAX      Integer32
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The value to use for the test specified by
+        mteTriggerBooleanTest."
+    DEFVAL { 0 }
+    ::= { mteTriggerBooleanEntry 2 }
+
+mteTriggerBooleanStartup OBJECT-TYPE
+    SYNTAX      TruthValue
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "Control for whether an event may be triggered when this entry
+        is first set to 'active' or a new instance of the object at
+        mteTriggerValueID is found and the test specified by
+        mteTriggerBooleanComparison is true.  In that case an event is
+        triggered if mteTriggerBooleanStartup is 'true'."
+    DEFVAL { true }
+    ::= { mteTriggerBooleanEntry 3 }
+
+mteTriggerBooleanObjectsOwner OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "To go with mteTriggerBooleanObjects, the mteOwner of a group
+        of objects from mteObjectsTable."
+    DEFVAL { ''H }
+    ::= { mteTriggerBooleanEntry 4 }
+
+mteTriggerBooleanObjects OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The mteObjectsName of a group of objects from
+        mteObjectsTable.  These objects are to be added to any
+        Notification resulting from the firing of this trigger for
+        this test.
+
+        A list of objects may also be added based on the overall
+        trigger, the event or other settings in mteTriggerTest.
+
+        A length of 0 indicates no additional objects."
+    DEFVAL { ''H }
+    ::= { mteTriggerBooleanEntry 5 }
+
+mteTriggerBooleanEventOwner OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "To go with mteTriggerBooleanEvent, the mteOwner of an event
+        entry from mteEventTable."
+    DEFVAL { ''H }
+    ::= { mteTriggerBooleanEntry 6 }
+
+mteTriggerBooleanEvent OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The mteEventName of the event to invoke when mteTriggerType is
+        'boolean' and this trigger fires.  A length of 0 indicates no
+        event."
+    DEFVAL { ''H }
+    ::= { mteTriggerBooleanEntry 7 }
+
+--
+-- Trigger Threshold Table
+--
+
+mteTriggerThresholdTable OBJECT-TYPE
+    SYNTAX      SEQUENCE OF MteTriggerThresholdEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "A table of management event trigger information for threshold
+        triggers."
+    ::= { mteTrigger 6 }
+
+mteTriggerThresholdEntry OBJECT-TYPE
+    SYNTAX      MteTriggerThresholdEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "Information about a single threshold trigger.  Entries
+        automatically exist in this table for each mteTriggerEntry
+        that has 'threshold' set in mteTriggerTest."
+    INDEX       { mteOwner, IMPLIED mteTriggerName }
+    ::= { mteTriggerThresholdTable 1 }
+
+MteTriggerThresholdEntry ::= SEQUENCE {
+    mteTriggerThresholdStartup                  INTEGER,
+    mteTriggerThresholdRising                   Integer32,
+    mteTriggerThresholdFalling                  Integer32,
+    mteTriggerThresholdDeltaRising              Integer32,
+    mteTriggerThresholdDeltaFalling             Integer32,
+    mteTriggerThresholdObjectsOwner             SnmpAdminString,
+    mteTriggerThresholdObjects                  SnmpAdminString,
+    mteTriggerThresholdRisingEventOwner         SnmpAdminString,
+    mteTriggerThresholdRisingEvent              SnmpAdminString,
+    mteTriggerThresholdFallingEventOwner        SnmpAdminString,
+    mteTriggerThresholdFallingEvent             SnmpAdminString,
+    mteTriggerThresholdDeltaRisingEventOwner    SnmpAdminString,
+    mteTriggerThresholdDeltaRisingEvent         SnmpAdminString,
+    mteTriggerThresholdDeltaFallingEventOwner   SnmpAdminString,
+    mteTriggerThresholdDeltaFallingEvent        SnmpAdminString
+}
+
+mteTriggerThresholdStartup OBJECT-TYPE
+    SYNTAX      INTEGER { rising(1), falling(2), risingOrFalling(3) }
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The event that may be triggered when this entry is first
+        set to 'active' and a new instance of the object at
+        mteTriggerValueID is found.  If the first sample after this
+        instance becomes active is greater than or equal to
+        mteTriggerThresholdRising and mteTriggerThresholdStartup is
+        equal to 'rising' or 'risingOrFalling', then one
+        mteTriggerThresholdRisingEvent is triggered for that instance.
+        If the first sample after this entry becomes active is less
+        than or equal to mteTriggerThresholdFalling and
+        mteTriggerThresholdStartup is equal to 'falling' or
+        'risingOrFalling', then one mteTriggerThresholdRisingEvent is
+        triggered for that instance."
+    DEFVAL { risingOrFalling }
+    ::= { mteTriggerThresholdEntry 1 }
+
+mteTriggerThresholdRising OBJECT-TYPE
+    SYNTAX      Integer32
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "A threshold value to check against if mteTriggerType is
+        'threshold'.
+
+        When the current sampled value is greater than or equal to
+        this threshold, and the value at the last sampling interval
+        was less than this threshold, one
+        mteTriggerThresholdRisingEvent is triggered.  That event is
+        also triggered if the first sample after this entry becomes
+        active is greater than or equal to this threshold and
+        mteTriggerThresholdStartup is equal to 'rising' or
+        'risingOrFalling'.
+
+        After a rising event is generated, another such event is not
+        triggered until the sampled value falls below this threshold
+        and reaches mteTriggerThresholdFalling."
+    DEFVAL { 0 }
+    ::= { mteTriggerThresholdEntry 2 }
+
+mteTriggerThresholdFalling OBJECT-TYPE
+    SYNTAX      Integer32
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "A threshold value to check against if mteTriggerType is
+        'threshold'.
+
+        When the current sampled value is less than or equal to this
+        threshold, and the value at the last sampling interval was
+        greater than this threshold, one
+        mteTriggerThresholdFallingEvent is triggered.  That event is
+        also triggered if the first sample after this entry becomes
+        active is less than or equal to this threshold and
+        mteTriggerThresholdStartup is equal to 'falling' or
+        'risingOrFalling'.
+
+        After a falling event is generated, another such event is not
+        triggered until the sampled value rises above this threshold
+        and reaches mteTriggerThresholdRising."
+    DEFVAL { 0 }
+    ::= { mteTriggerThresholdEntry 3 }
+
+mteTriggerThresholdDeltaRising OBJECT-TYPE
+    SYNTAX      Integer32
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "A threshold value to check against if mteTriggerType is
+        'threshold'.
+
+        When the delta value (difference) between the current sampled
+        value (value(n)) and the previous sampled value (value(n-1))
+        is greater than or equal to this threshold,
+        and the delta value calculated at the last sampling interval
+        (i.e. value(n-1) - value(n-2)) was less than this threshold,
+        one mteTriggerThresholdDeltaRisingEvent is triggered. That event
+        is also triggered if the first delta value calculated after this
+        entry becomes active, i.e. value(2) - value(1), where value(1)
+        is the first sample taken of that instance, is greater than or
+        equal to this threshold.
+
+        After a rising event is generated, another such event is not
+        triggered until the delta value falls below this threshold and
+        reaches mteTriggerThresholdDeltaFalling."
+    DEFVAL { 0 }
+    ::= { mteTriggerThresholdEntry 4 }
+
+mteTriggerThresholdDeltaFalling OBJECT-TYPE
+    SYNTAX      Integer32
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "A threshold value to check against if mteTriggerType is
+        'threshold'.
+
+        When the delta value (difference) between the current sampled
+        value (value(n)) and the previous sampled value (value(n-1))
+        is less than or equal to this threshold,
+        and the delta value calculated at the last sampling interval
+        (i.e. value(n-1) - value(n-2)) was greater than this threshold,
+        one mteTriggerThresholdDeltaFallingEvent is triggered. That event
+        is also triggered if the first delta value calculated after this
+        entry becomes active, i.e. value(2) - value(1), where value(1)
+        is the first sample taken of that instance, is less than or
+        equal to this threshold.
+
+        After a falling event is generated, another such event is not
+        triggered until the delta value falls below this threshold and
+        reaches mteTriggerThresholdDeltaRising."
+    DEFVAL { 0 }
+    ::= { mteTriggerThresholdEntry 5 }
+
+mteTriggerThresholdObjectsOwner OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "To go with mteTriggerThresholdObjects, the mteOwner of a group
+        of objects from mteObjectsTable."
+    DEFVAL { ''H }
+    ::= { mteTriggerThresholdEntry 6 }
+
+mteTriggerThresholdObjects OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The mteObjectsName of a group of objects from
+        mteObjectsTable.  These objects are to be added to any
+        Notification resulting from the firing of this trigger for
+        this test.
+
+        A list of objects may also be added based on the overall
+
+        trigger, the event or other settings in mteTriggerTest.
+
+        A length of 0 indicates no additional objects."
+    DEFVAL { ''H }
+    ::= { mteTriggerThresholdEntry 7 }
+
+mteTriggerThresholdRisingEventOwner OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "To go with mteTriggerThresholdRisingEvent, the mteOwner of an
+        event entry from mteEventTable."
+    DEFVAL { ''H }
+    ::= { mteTriggerThresholdEntry 8 }
+
+mteTriggerThresholdRisingEvent OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The mteEventName of the event to invoke when mteTriggerType is
+        'threshold' and this trigger fires based on
+        mteTriggerThresholdRising.  A length of 0 indicates no event."
+    DEFVAL { ''H }
+    ::= { mteTriggerThresholdEntry 9 }
+
+mteTriggerThresholdFallingEventOwner OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "To go with mteTriggerThresholdFallingEvent, the mteOwner of an
+        event entry from mteEventTable."
+    DEFVAL { ''H }
+    ::= { mteTriggerThresholdEntry 10 }
+
+mteTriggerThresholdFallingEvent OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The mteEventName of the event to invoke when mteTriggerType is
+        'threshold' and this trigger fires based on
+        mteTriggerThresholdFalling.  A length of 0 indicates no event."
+    DEFVAL { ''H }
+    ::= { mteTriggerThresholdEntry 11 }
+
+mteTriggerThresholdDeltaRisingEventOwner OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "To go with mteTriggerThresholdDeltaRisingEvent, the mteOwner
+        of an event entry from mteEventTable."
+    DEFVAL { ''H }
+    ::= { mteTriggerThresholdEntry 12 }
+
+mteTriggerThresholdDeltaRisingEvent OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The mteEventName of the event to invoke when mteTriggerType is
+        'threshold' and this trigger fires based on
+        mteTriggerThresholdDeltaRising. A length of 0 indicates
+        no event."
+    DEFVAL { ''H }
+    ::= { mteTriggerThresholdEntry 13 }
+
+mteTriggerThresholdDeltaFallingEventOwner OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "To go with mteTriggerThresholdDeltaFallingEvent, the mteOwner
+        of an event entry from mteEventTable."
+    DEFVAL { ''H }
+    ::= { mteTriggerThresholdEntry 14 }
+
+mteTriggerThresholdDeltaFallingEvent OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The mteEventName of the event to invoke when mteTriggerType is
+        'threshold' and this trigger fires based on
+        mteTriggerThresholdDeltaFalling.  A length of 0 indicates
+        no event."
+    DEFVAL { ''H }
+    ::= { mteTriggerThresholdEntry 15 }
+
+--
+-- Objects Table
+--
+
+mteObjectsTable OBJECT-TYPE
+    SYNTAX      SEQUENCE OF MteObjectsEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "A table of objects that can be added to notifications based
+        on the trigger, trigger test, or event, as pointed to by
+        entries in those tables."
+    ::= { mteObjects 1 }
+
+mteObjectsEntry OBJECT-TYPE
+    SYNTAX      MteObjectsEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "A group of objects.  Applications create and delete entries
+        using mteObjectsEntryStatus.
+
+        When adding objects to a notification they are added in the
+        lexical order of their index in this table.  Those associated
+        with a trigger come first, then trigger test, then event."
+    INDEX       { mteOwner, mteObjectsName, mteObjectsIndex }
+    ::= { mteObjectsTable 1 }
+
+MteObjectsEntry ::= SEQUENCE {
+    mteObjectsName                      SnmpAdminString,
+    mteObjectsIndex                     Unsigned32,
+    mteObjectsID                        OBJECT IDENTIFIER,
+    mteObjectsIDWildcard                TruthValue,
+    mteObjectsEntryStatus               RowStatus
+    }
+
+mteObjectsName OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (1..32))
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "A locally-unique, administratively assigned name for a group
+        of objects."
+    ::= { mteObjectsEntry 1 }
+
+mteObjectsIndex OBJECT-TYPE
+    SYNTAX      Unsigned32 (1..4294967295)
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "An arbitrary integer for the purpose of identifying
+        individual objects within a mteObjectsName group.
+
+        Objects within a group are placed in the notification in the
+        numerical order of this index.
+
+        Groups are placed in the notification in the order of the
+        selections for overall trigger, trigger test, and event.
+        Within trigger test they are in the same order as the
+        numerical values of the bits defined for mteTriggerTest.
+
+        Bad object identifiers or a mismatch between truncating the
+        identifier and the value of mteDeltaDiscontinuityIDWildcard
+        result in operation as one would expect when providing the
+        wrong identifier to a Get operation.  The Get will fail or get
+        the wrong object.  If the object is not available it is omitted
+        from the notification."
+    ::= { mteObjectsEntry 2 }
+
+mteObjectsID OBJECT-TYPE
+    SYNTAX      OBJECT IDENTIFIER
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "The object identifier of a MIB object to add to a
+        Notification that results from the firing of a trigger.
+
+        This may be wildcarded by truncating all or part of the
+        instance portion, in which case the instance portion of the
+        OID for obtaining this object will be the same as that used
+        in obtaining the mteTriggerValueID that fired.  If such
+        wildcarding is applied, mteObjectsIDWildcard must be
+        'true' and if not it must be 'false'.
+
+        Each instance that fills the wildcard is independent of any
+        additional instances, that is, wildcarded objects operate
+        as if there were a separate table entry for each instance
+        that fills the wildcard without having to actually predict
+        all possible instances ahead of time."
+    DEFVAL { zeroDotZero }
+    ::= { mteObjectsEntry 3 }
+
+mteObjectsIDWildcard OBJECT-TYPE
+    SYNTAX      TruthValue
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "Control for whether mteObjectsID is to be treated as
+        fully-specified or wildcarded, with 'true' indicating wildcard."
+    DEFVAL { false }
+    ::= { mteObjectsEntry 4 }
+
+mteObjectsEntryStatus OBJECT-TYPE
+    SYNTAX      RowStatus
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "The control that allows creation and deletion of entries.
+        Once made active an entry MAY not be modified except to
+        delete it."
+    ::= { mteObjectsEntry 5 }
+
+--
+-- Event Section
+--
+
+-- Counters
+
+mteEventFailures OBJECT-TYPE
+    SYNTAX      Counter32
+    MAX-ACCESS  read-only
+    STATUS      current
+    DESCRIPTION
+        "The number of times an attempt to invoke an event
+        has failed.  This counts individually for each
+        attempt in a group of targets or each attempt for a
+        wildcarded trigger object."
+    ::= { mteEvent 1 }
+
+--
+-- Event Table
+--
+
+mteEventTable OBJECT-TYPE
+    SYNTAX      SEQUENCE OF MteEventEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "A table of management event action information."
+    ::= { mteEvent 2 }
+
+mteEventEntry OBJECT-TYPE
+    SYNTAX      MteEventEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "Information about a single event.  Applications create and
+        delete entries using mteEventEntryStatus."
+    INDEX       { mteOwner, IMPLIED mteEventName }
+    ::= { mteEventTable 1 }
+
+MteEventEntry ::= SEQUENCE {
+    mteEventName                        SnmpAdminString,
+    mteEventComment                     SnmpAdminString,
+    mteEventActions                     BITS,
+    mteEventEnabled                     TruthValue,
+    mteEventEntryStatus                 RowStatus
+    }
+
+mteEventName OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (1..32))
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "A locally-unique, administratively assigned name for the
+        event."
+    ::= { mteEventEntry 1 }
+
+mteEventComment OBJECT-TYPE
+    SYNTAX      SnmpAdminString
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "A description of the event's function and use."
+    DEFVAL { ''H }
+    ::= { mteEventEntry 2 }
+
+mteEventActions OBJECT-TYPE
+    SYNTAX      BITS { notification(0), set(1) }
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "The actions to perform when this event occurs.
+
+        For 'notification', Traps and/or Informs are sent according
+        to the configuration in the SNMP Notification MIB.
+
+        For 'set', an SNMP Set operation is performed according to
+        control values in this entry."
+    DEFVAL { {} }  -- No bits set.
+    ::= { mteEventEntry 3 }
+
+mteEventEnabled OBJECT-TYPE
+    SYNTAX      TruthValue
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "A control to allow an event to be configured but not used.
+        When the value is 'false' the event does not execute even if
+
+        triggered."
+    DEFVAL { false }
+    ::= { mteEventEntry 4 }
+
+mteEventEntryStatus OBJECT-TYPE
+    SYNTAX      RowStatus
+    MAX-ACCESS  read-create
+    STATUS      current
+    DESCRIPTION
+        "The control that allows creation and deletion of entries.
+        Once made active an entry MAY not be modified except to
+        delete it."
+    ::= { mteEventEntry 5 }
+
+--
+-- Event Notification Table
+--
+
+mteEventNotificationTable OBJECT-TYPE
+    SYNTAX      SEQUENCE OF MteEventNotificationEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "A table of information about notifications to be sent as a
+        consequence of management events."
+    ::= { mteEvent 3 }
+
+mteEventNotificationEntry OBJECT-TYPE
+    SYNTAX      MteEventNotificationEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "Information about a single event's notification.  Entries
+        automatically exist in this this table for each mteEventEntry
+        that has 'notification' set in mteEventActions."
+    INDEX       { mteOwner, IMPLIED mteEventName }
+    ::= { mteEventNotificationTable 1 }
+
+MteEventNotificationEntry ::= SEQUENCE {
+    mteEventNotification                OBJECT IDENTIFIER,
+    mteEventNotificationObjectsOwner    SnmpAdminString,
+    mteEventNotificationObjects         SnmpAdminString
+    }
+
+mteEventNotification OBJECT-TYPE
+    SYNTAX      OBJECT IDENTIFIER
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The object identifier from the NOTIFICATION-TYPE for the
+        notification to use if metEventActions has 'notification' set."
+    DEFVAL { zeroDotZero }
+    ::= { mteEventNotificationEntry 1 }
+
+mteEventNotificationObjectsOwner OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "To go with mteEventNotificationObjects, the mteOwner of a
+        group of objects from mteObjectsTable."
+    DEFVAL { ''H }
+    ::= { mteEventNotificationEntry 2 }
+
+mteEventNotificationObjects OBJECT-TYPE
+    SYNTAX      SnmpAdminString (SIZE (0..32))
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The mteObjectsName of a group of objects from
+        mteObjectsTable if mteEventActions has 'notification' set.
+        These objects are to be added to any Notification generated by
+        this event.
+
+        Objects may also be added based on the trigger that stimulated
+        the event.
+
+        A length of 0 indicates no additional objects."
+    DEFVAL { ''H }
+    ::= { mteEventNotificationEntry 3 }
+
+--
+-- Event Set Table
+--
+
+mteEventSetTable OBJECT-TYPE
+    SYNTAX      SEQUENCE OF MteEventSetEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "A table of management event action information."
+    ::= { mteEvent 4 }
+
+mteEventSetEntry OBJECT-TYPE
+    SYNTAX      MteEventSetEntry
+    MAX-ACCESS  not-accessible
+    STATUS      current
+    DESCRIPTION
+        "Information about a single event's set option.  Entries
+        automatically exist in this this table for each mteEventEntry
+        that has 'set' set in mteEventActions."
+    INDEX       { mteOwner, IMPLIED mteEventName }
+    ::= { mteEventSetTable 1 }
+
+MteEventSetEntry ::= SEQUENCE {
+    mteEventSetObject                   OBJECT IDENTIFIER,
+    mteEventSetObjectWildcard           TruthValue,
+    mteEventSetValue                    Integer32,
+    mteEventSetTargetTag                SnmpTagValue,
+    mteEventSetContextName              SnmpAdminString,
+    mteEventSetContextNameWildcard      TruthValue
+    }
+
+mteEventSetObject OBJECT-TYPE
+    SYNTAX      OBJECT IDENTIFIER
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The object identifier from the MIB object to set if
+        mteEventActions has 'set' set.
+
+        This object identifier may be wildcarded by leaving
+        sub-identifiers off the end, in which case
+        nteEventSetObjectWildCard must be 'true'.
+
+        If mteEventSetObject is wildcarded the instance used to set the
+        object to which it points is the same as the instance from the
+        value of mteTriggerValueID that triggered the event.
+
+        Each instance that fills the wildcard is independent of any
+        additional instances, that is, wildcarded objects operate
+        as if there were a separate table entry for each instance
+        that fills the wildcard without having to actually predict
+        all possible instances ahead of time.
+
+        Bad object identifiers or a mismatch between truncating the
+        identifier and the value of mteSetObjectWildcard
+        result in operation as one would expect when providing the
+        wrong identifier to a Set operation.  The Set will fail or set
+        the wrong object.  If the value syntax of the destination
+        object is not correct, the Set fails with the normal SNMP
+        error code."
+    DEFVAL { zeroDotZero }
+    ::= { mteEventSetEntry 1 }
+
+mteEventSetObjectWildcard OBJECT-TYPE
+    SYNTAX      TruthValue
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "Control over whether mteEventSetObject is to be treated as
+        fully-specified or wildcarded, with 'true' indicating wildcard
+        if mteEventActions has 'set' set."
+    DEFVAL { false }
+    ::= { mteEventSetEntry 2 }
+
+mteEventSetValue OBJECT-TYPE
+    SYNTAX      Integer32
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The value to which to set the object at mteEventSetObject
+        if mteEventActions has 'set' set."
+    DEFVAL { 0 }
+    ::= { mteEventSetEntry 3 }
+
+mteEventSetTargetTag OBJECT-TYPE
+    SYNTAX      SnmpTagValue
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The tag for the target(s) at which to set the object at
+        mteEventSetObject to mteEventSetValue if mteEventActions
+        has 'set' set.
+
+        Systems limited to self management MAY reject a non-zero
+        length for the value of this object.
+
+        A length of 0 indicates the local system.  In this case,
+        access to the objects indicated by mteEventSetObject is under
+        the security credentials of the requester that set
+        mteTriggerEntryStatus to 'active'.  Those credentials are the
+        input parameters for isAccessAllowed from the Architecture for
+        Describing SNMP Management Frameworks.
+
+        Otherwise access rights are checked according to the security
+        parameters resulting from the tag."
+    DEFVAL { ''H }
+    ::= { mteEventSetEntry 4 }
+
+mteEventSetContextName OBJECT-TYPE
+    SYNTAX      SnmpAdminString
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "The management context in which to set mteEventObjectID.
+        if mteEventActions has 'set' set.
+
+        This may be wildcarded by leaving characters off the end.  To
+        indicate such wildcarding mteEventSetContextNameWildcard must
+        be 'true'.
+
+        If this context name is wildcarded the value used to complete
+        the wildcarding of mteTriggerContextName will be appended."
+    DEFVAL { ''H }
+    ::= { mteEventSetEntry 5 }
+
+mteEventSetContextNameWildcard OBJECT-TYPE
+    SYNTAX      TruthValue
+    MAX-ACCESS  read-write
+    STATUS      current
+    DESCRIPTION
+        "Control for whether mteEventSetContextName is to be treated as
+        fully-specified or wildcarded, with 'true' indicating wildcard
+        if mteEventActions has 'set' set."
+    DEFVAL { false }
+    ::= { mteEventSetEntry 6 }
+
+--
+-- Notifications
+--
+
+dismanEventMIBNotificationPrefix OBJECT IDENTIFIER ::=
+    { dismanEventMIB 2 }
+dismanEventMIBNotifications OBJECT IDENTIFIER ::=
+    { dismanEventMIBNotificationPrefix 0 }
+dismanEventMIBNotificationObjects OBJECT IDENTIFIER
+   ::= { dismanEventMIBNotificationPrefix 1 }
+
+--
+-- Notification Objects
+--
+
+mteHotTrigger OBJECT-TYPE
+    SYNTAX      SnmpAdminString
+    MAX-ACCESS  accessible-for-notify
+    STATUS      current
+    DESCRIPTION
+        "The name of the trigger causing the notification."
+    ::= { dismanEventMIBNotificationObjects 1 }
+
+mteHotTargetName OBJECT-TYPE
+    SYNTAX      SnmpAdminString
+    MAX-ACCESS  accessible-for-notify
+    STATUS      current
+    DESCRIPTION
+        "The SNMP Target MIB's snmpTargetAddrName related to the
+        notification."
+    ::= { dismanEventMIBNotificationObjects 2 }
+
+mteHotContextName OBJECT-TYPE
+    SYNTAX      SnmpAdminString
+    MAX-ACCESS  accessible-for-notify
+    STATUS      current
+    DESCRIPTION
+        "The context name related to the notification.  This MUST be as
+        fully-qualified as possible, including filling in wildcard
+        information determined in processing."
+    ::= { dismanEventMIBNotificationObjects 3 }
+
+mteHotOID OBJECT-TYPE
+    SYNTAX      OBJECT IDENTIFIER
+    MAX-ACCESS  accessible-for-notify
+    STATUS      current
+    DESCRIPTION
+        "The object identifier of the destination object related to the
+        notification.  This MUST be as fully-qualified as possible,
+        including filling in wildcard information determined in
+        processing.
+
+        For a trigger-related notification this is from
+        mteTriggerValueID.
+
+        For a set failure this is from mteEventSetObject."
+    ::= { dismanEventMIBNotificationObjects 4 }
+
+mteHotValue OBJECT-TYPE
+    SYNTAX      Integer32
+    MAX-ACCESS  accessible-for-notify
+    STATUS      current
+    DESCRIPTION
+        "The value of the object at mteTriggerValueID when a
+        trigger fired."
+    ::= { dismanEventMIBNotificationObjects 5 }
+
+mteFailedReason OBJECT-TYPE
+    SYNTAX      FailureReason
+    MAX-ACCESS  accessible-for-notify
+    STATUS      current
+    DESCRIPTION
+        "The reason for the failure of an attempt to check for a
+        trigger condition or set an object in response to an event."
+    ::= { dismanEventMIBNotificationObjects 6 }
+
+--
+-- Notifications
+--
+
+mteTriggerFired NOTIFICATION-TYPE
+    OBJECTS { mteHotTrigger,
+              mteHotTargetName,
+              mteHotContextName,
+              mteHotOID,
+              mteHotValue }
+    STATUS  current
+    DESCRIPTION
+        "Notification that the trigger indicated by the object
+        instances has fired, for triggers with mteTriggerType
+        'boolean' or 'existence'."
+    ::= { dismanEventMIBNotifications 1 }
+
+mteTriggerRising NOTIFICATION-TYPE
+    OBJECTS { mteHotTrigger,
+              mteHotTargetName,
+              mteHotContextName,
+              mteHotOID,
+              mteHotValue }
+    STATUS  current
+    DESCRIPTION
+        "Notification that the rising threshold was met for triggers
+        with mteTriggerType 'threshold'."
+    ::= { dismanEventMIBNotifications 2 }
+
+mteTriggerFalling NOTIFICATION-TYPE
+    OBJECTS { mteHotTrigger,
+              mteHotTargetName,
+              mteHotContextName,
+              mteHotOID,
+              mteHotValue }
+    STATUS  current
+    DESCRIPTION
+        "Notification that the falling threshold was met for triggers
+        with mteTriggerType 'threshold'."
+    ::= { dismanEventMIBNotifications 3 }
+
+mteTriggerFailure NOTIFICATION-TYPE
+    OBJECTS { mteHotTrigger,
+              mteHotTargetName,
+              mteHotContextName,
+              mteHotOID,
+              mteFailedReason }
+    STATUS  current
+    DESCRIPTION
+        "Notification that an attempt to check a trigger has failed.
+
+        The network manager must enable this notification only with
+        a certain fear and trembling, as it can easily crowd out more
+        important information.  It should be used only to help diagnose
+        a problem that has appeared in the error counters and can not
+        be found otherwise."
+    ::= { dismanEventMIBNotifications 4 }
+
+mteEventSetFailure NOTIFICATION-TYPE
+    OBJECTS { mteHotTrigger,
+              mteHotTargetName,
+              mteHotContextName,
+              mteHotOID,
+              mteFailedReason }
+    STATUS  current
+    DESCRIPTION
+        "Notification that an attempt to do a set in response to an
+        event has failed.
+
+        The network manager must enable this notification only with
+        a certain fear and trembling, as it can easily crowd out more
+        important information.  It should be used only to help diagnose
+        a problem that has appeared in the error counters and can not
+        be found otherwise."
+    ::= { dismanEventMIBNotifications 5 }
+
+--
+-- Conformance
+--
+
+dismanEventMIBConformance OBJECT IDENTIFIER ::= { dismanEventMIB 3 }
+dismanEventMIBCompliances OBJECT IDENTIFIER ::=
+    { dismanEventMIBConformance 1 }
+dismanEventMIBGroups      OBJECT IDENTIFIER ::=
+    { dismanEventMIBConformance 2 }
+
+-- Compliance
+
+dismanEventMIBCompliance MODULE-COMPLIANCE
+        STATUS current
+        DESCRIPTION
+                "The compliance statement for entities which implement
+                the Event MIB."
+        MODULE  -- this module
+                MANDATORY-GROUPS {
+                        dismanEventResourceGroup,
+                        dismanEventTriggerGroup,
+                        dismanEventObjectsGroup,
+                        dismanEventEventGroup,
+                        dismanEventNotificationObjectGroup,
+                        dismanEventNotificationGroup
+                }
+
+                OBJECT mteTriggerTargetTag
+                MIN-ACCESS  read-only
+                DESCRIPTION
+                        "Write access is not required, thus limiting
+                        monitoring to the local system or pre-configured
+                        remote systems."
+
+                OBJECT mteEventSetTargetTag
+                MIN-ACCESS  read-only
+                DESCRIPTION
+                        "Write access is not required, thus limiting
+                        setting to the local system or pre-configured
+                        remote systems."
+
+                OBJECT mteTriggerValueIDWildcard
+                MIN-ACCESS  read-only
+                DESCRIPTION
+                        "Write access is not required, thus allowing
+                        the system not to implement wildcarding."
+
+                OBJECT mteTriggerContextNameWildcard
+                MIN-ACCESS  read-only
+                DESCRIPTION
+                        "Write access is not required, thus allowing
+                        the system not to implement wildcarding."
+
+                OBJECT mteObjectsIDWildcard
+                MIN-ACCESS  read-only
+                DESCRIPTION
+                        "Write access is not required, thus allowing
+                        the system not to implement wildcarding."
+
+                OBJECT mteEventSetContextNameWildcard
+                MIN-ACCESS  read-only
+                DESCRIPTION
+                        "Write access is not required, thus allowing
+                        the system not to implement wildcarding."
+        ::= { dismanEventMIBCompliances 1 }
+
+-- Units of Conformance
+
+dismanEventResourceGroup OBJECT-GROUP
+        OBJECTS {
+                mteResourceSampleMinimum,
+                mteResourceSampleInstanceMaximum,
+                mteResourceSampleInstances,
+                mteResourceSampleInstancesHigh,
+                mteResourceSampleInstanceLacks
+        }
+        STATUS current
+        DESCRIPTION
+                "Event resource status and control objects."
+        ::= { dismanEventMIBGroups 1 }
+
+dismanEventTriggerGroup OBJECT-GROUP
+        OBJECTS {
+                mteTriggerFailures,
+                mteTriggerComment,
+                mteTriggerTest,
+                mteTriggerSampleType,
+                mteTriggerValueID,
+                mteTriggerValueIDWildcard,
+                mteTriggerTargetTag,
+                mteTriggerContextName,
+                mteTriggerContextNameWildcard,
+                mteTriggerFrequency,
+                mteTriggerObjectsOwner,
+                mteTriggerObjects,
+                mteTriggerEnabled,
+                mteTriggerEntryStatus,
+                mteTriggerDeltaDiscontinuityID,
+                mteTriggerDeltaDiscontinuityIDWildcard,
+                mteTriggerDeltaDiscontinuityIDType,
+                mteTriggerExistenceTest,
+                mteTriggerExistenceStartup,
+                mteTriggerExistenceObjectsOwner,
+                mteTriggerExistenceObjects,
+                mteTriggerExistenceEventOwner,
+                mteTriggerExistenceEvent,
+                mteTriggerBooleanComparison,
+                mteTriggerBooleanValue,
+                mteTriggerBooleanStartup,
+                mteTriggerBooleanObjectsOwner,
+                mteTriggerBooleanObjects,
+                mteTriggerBooleanEventOwner,
+                mteTriggerBooleanEvent,
+                mteTriggerThresholdStartup,
+                mteTriggerThresholdObjectsOwner,
+                mteTriggerThresholdObjects,
+                mteTriggerThresholdRising,
+                mteTriggerThresholdFalling,
+                mteTriggerThresholdDeltaRising,
+                mteTriggerThresholdDeltaFalling,
+                mteTriggerThresholdRisingEventOwner,
+                mteTriggerThresholdRisingEvent,
+                mteTriggerThresholdFallingEventOwner,
+                mteTriggerThresholdFallingEvent,
+                mteTriggerThresholdDeltaRisingEventOwner,
+                mteTriggerThresholdDeltaRisingEvent,
+                mteTriggerThresholdDeltaFallingEventOwner,
+                mteTriggerThresholdDeltaFallingEvent
+        }
+        STATUS current
+        DESCRIPTION
+                "Event triggers."
+        ::= { dismanEventMIBGroups 2 }
+
+dismanEventObjectsGroup OBJECT-GROUP
+        OBJECTS {
+                mteObjectsID,
+                mteObjectsIDWildcard,
+                mteObjectsEntryStatus
+        }
+        STATUS current
+        DESCRIPTION
+                "Supplemental objects."
+        ::= { dismanEventMIBGroups 3 }
+
+dismanEventEventGroup OBJECT-GROUP
+        OBJECTS {
+                mteEventFailures,
+                mteEventComment,
+                mteEventActions,
+                mteEventEnabled,
+                mteEventEntryStatus,
+                mteEventNotification,
+                mteEventNotificationObjectsOwner,
+                mteEventNotificationObjects,
+                mteEventSetObject,
+                mteEventSetObjectWildcard,
+                mteEventSetValue,
+                mteEventSetTargetTag,
+                mteEventSetContextName,
+                mteEventSetContextNameWildcard
+        }
+        STATUS current
+        DESCRIPTION
+                "Events."
+        ::= { dismanEventMIBGroups 4 }
+
+dismanEventNotificationObjectGroup OBJECT-GROUP
+        OBJECTS {
+                mteHotTrigger,
+                mteHotTargetName,
+                mteHotContextName,
+                mteHotOID,
+                mteHotValue,
+                mteFailedReason
+        }
+        STATUS current
+        DESCRIPTION
+                "Notification objects."
+        ::= { dismanEventMIBGroups 5 }
+
+dismanEventNotificationGroup NOTIFICATION-GROUP
+        NOTIFICATIONS {
+                mteTriggerFired,
+                mteTriggerRising,
+                mteTriggerFalling,
+                mteTriggerFailure,
+                mteEventSetFailure
+        }
+        STATUS current
+        DESCRIPTION
+                "Notifications."
+        ::= { dismanEventMIBGroups 6 }
+
+END