summaryrefslogtreecommitdiff
path: root/data/templates/pppoe/ipv6-up.script.tmpl
diff options
context:
space:
mode:
Diffstat (limited to 'data/templates/pppoe/ipv6-up.script.tmpl')
-rw-r--r--data/templates/pppoe/ipv6-up.script.tmpl24
1 files changed, 11 insertions, 13 deletions
diff --git a/data/templates/pppoe/ipv6-up.script.tmpl b/data/templates/pppoe/ipv6-up.script.tmpl
index 097f1d4c3..511e288ea 100644
--- a/data/templates/pppoe/ipv6-up.script.tmpl
+++ b/data/templates/pppoe/ipv6-up.script.tmpl
@@ -3,17 +3,15 @@
# As PPPoE is an "on demand" interface we need to re-configure it when it
# becomes up
-if [ "$6" != "{{ intf }}" ]; then
+if [ "$6" != "{{ ifname }}" ]; then
exit
fi
-set -x
-
{% if ipv6_autoconf -%}
# add some info to syslog
-DIALER_PID=$(cat /var/run/{{ intf }}.pid)
+DIALER_PID=$(cat /var/run/{{ ifname }}.pid)
logger -t pppd[$DIALER_PID] "executing $0"
-logger -t pppd[$DIALER_PID] "configuring interface {{ intf }} via {{ source_interface }}"
+logger -t pppd[$DIALER_PID] "configuring interface {{ ifname }} via {{ source_interface }}"
# Configure interface-specific Host/Router behaviour.
# Note: It is recommended to have the same setting on all interfaces; mixed
@@ -22,7 +20,7 @@ logger -t pppd[$DIALER_PID] "configuring interface {{ intf }} via {{ source_inte
# 0 Forwarding disabled
# 1 Forwarding enabled
#
-echo 1 > /proc/sys/net/ipv6/conf/{{ intf }}/forwarding
+echo 1 > /proc/sys/net/ipv6/conf/{{ ifname }}/forwarding
# Accept Router Advertisements; autoconfigure using them.
#
@@ -36,15 +34,15 @@ echo 1 > /proc/sys/net/ipv6/conf/{{ intf }}/forwarding
# 2 Overrule forwarding behaviour. Accept Router Advertisements
# even if forwarding is enabled.
#
-echo 2 > /proc/sys/net/ipv6/conf/{{ intf }}/accept_ra
+echo 2 > /proc/sys/net/ipv6/conf/{{ ifname }}/accept_ra
# Autoconfigure addresses using Prefix Information in Router Advertisements.
-echo 1 > /proc/sys/net/ipv6/conf/{{ intf }}/autoconf
+echo 1 > /proc/sys/net/ipv6/conf/{{ ifname }}/autoconf
{% endif %}
{% if dhcpv6_pd_interfaces %}
# Start wide dhcpv6 client
-systemctl start dhcp6c@{{ intf }}.service
+systemctl start dhcp6c@{{ ifname }}.service
{% endif %}
@@ -54,9 +52,9 @@ systemctl start dhcp6c@{{ intf }}.service
SED_OPT="^ipv6 route"
VRF_NAME=""
-if [ -d /sys/class/net/{{ intf }}/upper_* ]; then
+if [ -d /sys/class/net/{{ ifname }}/upper_* ]; then
# Determine upper (VRF) interface
- VRF=$(basename $(ls -d /sys/class/net/{{ intf }}/upper_*))
+ VRF=$(basename $(ls -d /sys/class/net/{{ ifname }}/upper_*))
# Remove upper_ prefix from result string
VRF=${VRF#"upper_"}
# generate new SED command
@@ -80,8 +78,8 @@ done
{% endif %}
# Add default route to default or VRF routing table
-vtysh -c "conf t" ${VTY_OPT} -c "ipv6 route ::/0 {{ intf }} ${VRF_NAME}"
-logger -t pppd[$DIALER_PID] "added default route via {{ intf }} ${VRF_NAME}"
+vtysh -c "conf t" ${VTY_OPT} -c "ipv6 route ::/0 {{ ifname }} ${VRF_NAME}"
+logger -t pppd[$DIALER_PID] "added default route via {{ ifname }} ${VRF_NAME}"
{% endif %}