diff options
Diffstat (limited to 'data/templates/ser2net/ser2net.conf.tmpl')
| -rw-r--r-- | data/templates/ser2net/ser2net.conf.tmpl | 78 |
1 files changed, 78 insertions, 0 deletions
diff --git a/data/templates/ser2net/ser2net.conf.tmpl b/data/templates/ser2net/ser2net.conf.tmpl new file mode 100644 index 000000000..202fe8104 --- /dev/null +++ b/data/templates/ser2net/ser2net.conf.tmpl @@ -0,0 +1,78 @@ +### Autogenerated by ser2net.py ### + +# This is the configuration file for ser2net. It has the following format: +# <TCP port>:<state>:<timeout>:<device>:<options> +# TCP port +# Name or number of the TCP/IP port to accept con- +# nections from for this device. A port number may +# be of the form [host,]port, such as 127.0.0.1,2000 +# or localhost,2000. If this is specified, it will +# only bind to the IP address specified. Otherwise +# it will bind to all the ports on the machine. +# +# state Either raw or rawlp or telnet or off. off disables +# the port from accepting connections. It can be +# turned on later from the control port. raw enables +# the port and transfers all data as-is between the +# port and the long. rawlp enables the port and +# transfers all input data to device, device is open +# without any termios setting. It allow to use +# /dev/lpX devices and printers connected to them. +# telnet enables the port and runs the telnet proto- +# col on the port to set up telnet parameters. This +# is most useful for using telnet. +# +# timeout +# The time (in seconds) before the port will be dis- +# connected if there is no activity on it. A zero +# value disables this funciton. +# +# device The name of the device to connect to. This +# must be in the form of /dev/<device>. +# +# options +# Sets operational parameters for the serial port. +# Options 300, 1200, 2400, 4800, 9600, 19200, 38400, +# 57600, 115200 set the various baud rates. EVEN, +# ODD, NONE set the parity. 1STOPBIT, 2STOPBITS set +# the number of stop bits. 7DATABITS, 8DATABITS set +# the number of data bits. [-]XONXOFF turns on (- +# off) XON/XOFF support. [-]RTSCTS turns on (- off) +# hardware flow control, [-]LOCAL turns off (- on) +# monitoring of the modem lines, and +# [-]HANGUP_WHEN_DONE turns on (- off) lowering the +# modem control lines when the connextion is done. +# NOBREAK disables automatic setting of the break +# setting of the serial port. +# The "remctl" option allow remote control (ala RFC +# 2217) of serial-port configuration. A banner name +# may also be specified, that banner will be printed +# for the line. If no banner is given, then no +# banner is printed. +# +# or... + +# BANNER:<banner name>:banner +# This will create a banner, if the banner name is given in the +# options of a line, that banner will be printed. This takes the +# standard "C" \x characters (\r is carraige return, \n is newline, +# etc.). It also accepts \d, which prints the device name, \p, +# which prints the TCP port number, and \s which prints the serial +# parameters (eg 9600N81). Banners can span lines if the last +# character on a line is '\'. Note that you *must* use \r\n to +# start a new line. +# +# Note that the same device can be listed multiple times under different +# ports, this allows the same serial port to have both telnet and raw +# protocols. + +# The original config file shipped with the upstream sources can be +# found in /usr/share/doc/ser2net/examples + +BANNER:banner:\r\nser2net port \p device \d [\s] (VyOS)\r\n\r\n + +#3001:telnet:600:/dev/ttyS1:19200 8DATABITS NONE 1STOPBIT banner + +{% for d in devices %} +localhost,{{ d.port }}:telnet:{{ d.timeout }}:{{ d.serial_port }}:{{ d.speed }} {{ d.data_bits}}DATABITS {{ d.parity | upper }} {{ d.stop_bits}}STOPBIT banner +{% endfor %} |