diff options
Diffstat (limited to 'data/templates/ser2net/ser2net.conf.tmpl')
| -rw-r--r-- | data/templates/ser2net/ser2net.conf.tmpl | 76 |
1 files changed, 0 insertions, 76 deletions
diff --git a/data/templates/ser2net/ser2net.conf.tmpl b/data/templates/ser2net/ser2net.conf.tmpl deleted file mode 100644 index 0e946e84e..000000000 --- a/data/templates/ser2net/ser2net.conf.tmpl +++ /dev/null @@ -1,76 +0,0 @@ -### Autogenerated by ser2net.py ### - -# This is the configuration file for ser2net. It has the following format: -# <TCP port>:<state>:<timeout>:<device>:<options> -# TCP port -# Name or number of the TCP/IP port to accept con- -# nections from for this device. A port number may -# be of the form [host,]port, such as 127.0.0.1,2000 -# or localhost,2000. If this is specified, it will -# only bind to the IP address specified. Otherwise -# it will bind to all the ports on the machine. -# -# state Either raw or rawlp or telnet or off. off disables -# the port from accepting connections. It can be -# turned on later from the control port. raw enables -# the port and transfers all data as-is between the -# port and the long. rawlp enables the port and -# transfers all input data to device, device is open -# without any termios setting. It allow to use -# /dev/lpX devices and printers connected to them. -# telnet enables the port and runs the telnet proto- -# col on the port to set up telnet parameters. This -# is most useful for using telnet. -# -# timeout -# The time (in seconds) before the port will be dis- -# connected if there is no activity on it. A zero -# value disables this funciton. -# -# device The name of the device to connect to. This -# must be in the form of /dev/<device>. -# -# options -# Sets operational parameters for the serial port. -# Options 300, 1200, 2400, 4800, 9600, 19200, 38400, -# 57600, 115200 set the various baud rates. EVEN, -# ODD, NONE set the parity. 1STOPBIT, 2STOPBITS set -# the number of stop bits. 7DATABITS, 8DATABITS set -# the number of data bits. [-]XONXOFF turns on (- -# off) XON/XOFF support. [-]RTSCTS turns on (- off) -# hardware flow control, [-]LOCAL turns off (- on) -# monitoring of the modem lines, and -# [-]HANGUP_WHEN_DONE turns on (- off) lowering the -# modem control lines when the connextion is done. -# NOBREAK disables automatic setting of the break -# setting of the serial port. -# The "remctl" option allow remote control (ala RFC -# 2217) of serial-port configuration. A banner name -# may also be specified, that banner will be printed -# for the line. If no banner is given, then no -# banner is printed. -# -# or... - -# BANNER:<banner name>:banner -# This will create a banner, if the banner name is given in the -# options of a line, that banner will be printed. This takes the -# standard "C" \x characters (\r is carraige return, \n is newline, -# etc.). It also accepts \d, which prints the device name, \p, -# which prints the TCP port number, and \s which prints the serial -# parameters (eg 9600N81). Banners can span lines if the last -# character on a line is '\'. Note that you *must* use \r\n to -# start a new line. -# -# Note that the same device can be listed multiple times under different -# ports, this allows the same serial port to have both telnet and raw -# protocols. - -# The original config file shipped with the upstream sources can be -# found in /usr/share/doc/ser2net/examples - -BANNER:banner:\r\nConnected to serial proxy device \d [\s]\r\n\r\n - -{% for d in devices %} -localhost,{{ d.port }}:telnet:{{ d.timeout }}:{{ d.serial_port }}:{{ d.speed }} {{ d.data_bits}}DATABITS {{ d.parity | upper }} {{ d.stop_bits}}STOPBIT banner -{% endfor %} |