summaryrefslogtreecommitdiff
path: root/data/templates/ser2net
diff options
context:
space:
mode:
Diffstat (limited to 'data/templates/ser2net')
-rw-r--r--data/templates/ser2net/ser2net.conf.tmpl78
1 files changed, 78 insertions, 0 deletions
diff --git a/data/templates/ser2net/ser2net.conf.tmpl b/data/templates/ser2net/ser2net.conf.tmpl
new file mode 100644
index 000000000..202fe8104
--- /dev/null
+++ b/data/templates/ser2net/ser2net.conf.tmpl
@@ -0,0 +1,78 @@
+### Autogenerated by ser2net.py ###
+
+# This is the configuration file for ser2net. It has the following format:
+# <TCP port>:<state>:<timeout>:<device>:<options>
+# TCP port
+# Name or number of the TCP/IP port to accept con-
+# nections from for this device. A port number may
+# be of the form [host,]port, such as 127.0.0.1,2000
+# or localhost,2000. If this is specified, it will
+# only bind to the IP address specified. Otherwise
+# it will bind to all the ports on the machine.
+#
+# state Either raw or rawlp or telnet or off. off disables
+# the port from accepting connections. It can be
+# turned on later from the control port. raw enables
+# the port and transfers all data as-is between the
+# port and the long. rawlp enables the port and
+# transfers all input data to device, device is open
+# without any termios setting. It allow to use
+# /dev/lpX devices and printers connected to them.
+# telnet enables the port and runs the telnet proto-
+# col on the port to set up telnet parameters. This
+# is most useful for using telnet.
+#
+# timeout
+# The time (in seconds) before the port will be dis-
+# connected if there is no activity on it. A zero
+# value disables this funciton.
+#
+# device The name of the device to connect to. This
+# must be in the form of /dev/<device>.
+#
+# options
+# Sets operational parameters for the serial port.
+# Options 300, 1200, 2400, 4800, 9600, 19200, 38400,
+# 57600, 115200 set the various baud rates. EVEN,
+# ODD, NONE set the parity. 1STOPBIT, 2STOPBITS set
+# the number of stop bits. 7DATABITS, 8DATABITS set
+# the number of data bits. [-]XONXOFF turns on (-
+# off) XON/XOFF support. [-]RTSCTS turns on (- off)
+# hardware flow control, [-]LOCAL turns off (- on)
+# monitoring of the modem lines, and
+# [-]HANGUP_WHEN_DONE turns on (- off) lowering the
+# modem control lines when the connextion is done.
+# NOBREAK disables automatic setting of the break
+# setting of the serial port.
+# The "remctl" option allow remote control (ala RFC
+# 2217) of serial-port configuration. A banner name
+# may also be specified, that banner will be printed
+# for the line. If no banner is given, then no
+# banner is printed.
+#
+# or...
+
+# BANNER:<banner name>:banner
+# This will create a banner, if the banner name is given in the
+# options of a line, that banner will be printed. This takes the
+# standard "C" \x characters (\r is carraige return, \n is newline,
+# etc.). It also accepts \d, which prints the device name, \p,
+# which prints the TCP port number, and \s which prints the serial
+# parameters (eg 9600N81). Banners can span lines if the last
+# character on a line is '\'. Note that you *must* use \r\n to
+# start a new line.
+#
+# Note that the same device can be listed multiple times under different
+# ports, this allows the same serial port to have both telnet and raw
+# protocols.
+
+# The original config file shipped with the upstream sources can be
+# found in /usr/share/doc/ser2net/examples
+
+BANNER:banner:\r\nser2net port \p device \d [\s] (VyOS)\r\n\r\n
+
+#3001:telnet:600:/dev/ttyS1:19200 8DATABITS NONE 1STOPBIT banner
+
+{% for d in devices %}
+localhost,{{ d.port }}:telnet:{{ d.timeout }}:{{ d.serial_port }}:{{ d.speed }} {{ d.data_bits}}DATABITS {{ d.parity | upper }} {{ d.stop_bits}}STOPBIT banner
+{% endfor %}