diff options
Diffstat (limited to 'data/templates')
-rw-r--r-- | data/templates/wifi/hostapd.conf.j2 | 3511 |
1 files changed, 3123 insertions, 388 deletions
diff --git a/data/templates/wifi/hostapd.conf.j2 b/data/templates/wifi/hostapd.conf.j2 index 769325b49..7b54ad9d6 100644 --- a/data/templates/wifi/hostapd.conf.j2 +++ b/data/templates/wifi/hostapd.conf.j2 @@ -1,108 +1,58 @@ {# j2lint: disable=operator-enclosed-by-spaces #} ### Autogenerated by interfaces_wireless.py ### +### hostapd.conf reference: +### https://w1.fi/cgit/hostap/tree/hostapd/hostapd.conf?h=hostap_2_10&id=cff80b4f7d3c0a47c052e8187d671710f48939e4 + {% if description is vyos_defined %} # Description: {{ description }} # User-friendly description of device; up to 32 octets encoded in UTF-8 device_name={{ description | truncate(32, True) }} {% endif %} -# AP netdevice name (without 'ap' postfix, i.e., wlan0 uses wlan0ap for -# management frames with the Host AP driver); wlan0 with many nl80211 drivers -# Note: This attribute can be overridden by the values supplied with the '-i' -# command line parameter. interface={{ ifname }} - {% if is_bridge_member is vyos_defined %} -# In case of atheros and nl80211 driver interfaces, an additional -# configuration parameter, bridge, may be used to notify hostapd if the -# interface is included in a bridge. This parameter is not used with Host AP -# driver. If the bridge parameter is not set, the drivers will automatically -# figure out the bridge interface (assuming sysfs is enabled and mounted to -# /sys) and this parameter may not be needed. -# -# For nl80211, this parameter can be used to request the AP interface to be -# added to the bridge automatically (brctl may refuse to do this before hostapd -# has been started to change the interface mode). If needed, the bridge -# interface is also created. {# as there can only be one bridge interface it is save to loop #} {% for bridge in is_bridge_member %} bridge={{ bridge }} {% endfor %} - -# WDS (4-address frame) mode with per-station virtual interfaces -# (only supported with driver=nl80211) -# This mode allows associated stations to use 4-address frames to allow layer 2 -# bridging to be used. wds_sta=1 {% endif %} - -# Driver interface type (hostap/wired/none/nl80211/bsd); -# default: hostap). nl80211 is used with all Linux mac80211 drivers. -# Use driver=none if building hostapd as a standalone RADIUS server that does -# not control any wireless/wired driver. driver=nl80211 - -# Levels (minimum value for logged events): -# 0 = verbose debugging -# 1 = debugging -# 2 = informational messages -# 3 = notification -# 4 = warning logger_syslog=-1 logger_syslog_level=0 logger_stdout=-1 logger_stdout_level=0 - +{# regulatory domain and protocol stuff #} {% if country_code %} -# Country code (ISO/IEC 3166-1). Used to set regulatory domain. -# Set as needed to indicate country in which device is operating. -# This can limit available channels and transmit power. +{# Watch out for default value of "00" - World Regulatory Domain is set by "XX" in hostapd.conf #} +{% if '00' in country_code %} +country_code=XX +{% else %} country_code={{ country_code | upper }} - -# Enable IEEE 802.11d. This advertises the country_code and the set of allowed -# channels and transmit power levels based on the regulatory limits. The -# country_code setting must be configured with the correct country for -# IEEE 802.11d functions. +{% endif %} ieee80211d=1 {% endif %} - {% if ssid %} -# SSID to be used in IEEE 802.11 management frames ssid={{ ssid }} {% endif %} - {% if channel %} -# Channel number (IEEE 802.11) -# (default: 0, i.e., not set) -# Please note that some drivers do not use this value from hostapd and the -# channel will need to be configured separately with iwconfig. channel={{ channel }} {% endif %} - {% if mode is vyos_defined %} -# Operation mode (a = IEEE 802.11a (5 GHz), b = IEEE 802.11b (2.4 GHz), -# g = IEEE 802.11g (2.4 GHz), ad = IEEE 802.11ad (60 GHz); a/g options are used -# with IEEE 802.11n (HT), too, to specify band). For IEEE 802.11ac (VHT), this -# needs to be set to hw_mode a. For IEEE 802.11ax (HE) on 6 GHz this needs -# to be set to hw_mode a. When using ACS (see channel parameter), a -# special value "any" can be used to indicate that any support band can be used. -# This special case is currently supported only with drivers with which -# offloaded ACS is used. {% if mode is vyos_defined('n') %} hw_mode=g {% elif mode is vyos_defined('ac') %} hw_mode=a ieee80211h=1 ieee80211ac=1 +{% elif mode is vyos_defined('ax') %} +hw_mode=a +ieee80211h=1 +ieee80211ax=1 {% else %} hw_mode={{ mode }} {% endif %} {% endif %} - -# ieee80211w: Whether management frame protection (MFP) is enabled -# 0 = disabled (default) -# 1 = optional -# 2 = required {% if 'disabled' in mgmt_frame_protection %} ieee80211w=0 {% elif 'optional' in mgmt_frame_protection %} @@ -110,43 +60,14 @@ ieee80211w=1 {% elif 'required' in mgmt_frame_protection %} ieee80211w=2 {% endif %} - -{% if capabilities is vyos_defined %} -# ht_capab: HT capabilities (list of flags) -# LDPC coding capability: [LDPC] = supported -# Supported channel width set: [HT40-] = both 20 MHz and 40 MHz with secondary -# channel below the primary channel; [HT40+] = both 20 MHz and 40 MHz -# with secondary channel above the primary channel -# (20 MHz only if neither is set) -# Note: There are limits on which channels can be used with HT40- and -# HT40+. Following table shows the channels that may be available for -# HT40- and HT40+ use per IEEE 802.11n Annex J: -# freq HT40- HT40+ -# 2.4 GHz 5-13 1-7 (1-9 in Europe/Japan) -# 5 GHz 40,48,56,64 36,44,52,60 -# (depending on the location, not all of these channels may be available -# for use) -# Please note that 40 MHz channels may switch their primary and secondary -# channels if needed or creation of 40 MHz channel maybe rejected based -# on overlapping BSSes. These changes are done automatically when hostapd -# is setting up the 40 MHz channel. -# Spatial Multiplexing (SM) Power Save: [SMPS-STATIC] or [SMPS-DYNAMIC] -# (SMPS disabled if neither is set) -# HT-greenfield: [GF] (disabled if not set) -# Short GI for 20 MHz: [SHORT-GI-20] (disabled if not set) -# Short GI for 40 MHz: [SHORT-GI-40] (disabled if not set) -# Tx STBC: [TX-STBC] (disabled if not set) -# Rx STBC: [RX-STBC1] (one spatial stream), [RX-STBC12] (one or two spatial -# streams), or [RX-STBC123] (one, two, or three spatial streams); Rx STBC -# disabled if none of these set -# HT-delayed Block Ack: [DELAYED-BA] (disabled if not set) -# Maximum A-MSDU length: [MAX-AMSDU-7935] for 7935 octets (3839 octets if not -# set) -# DSSS/CCK Mode in 40 MHz: [DSSS_CCK-40] = allowed (not allowed if not set) -# 40 MHz intolerant [40-INTOLERANT] (not advertised if not set) -# L-SIG TXOP protection support: [LSIG-TXOP-PROT] (disabled if not set) +{% if enable_bf_protection is vyos_defined %} +beacon_prot=1 +{% else %} +beacon_prot=0 +{% endif %} +{# HT (802.11n 2.4GHz and 5GHz) #} +{% if capabilities.ht is vyos_defined %} {% set output = namespace(value='') %} - {% if capabilities.ht.fourtymhz_incapable is vyos_defined %} {% set output.value = output.value ~ '[40-INTOLERANT]' %} {% endif %} @@ -177,38 +98,929 @@ ieee80211w=2 {% if capabilities.ht.smps is vyos_defined %} {% set output.value = output.value ~ '[SMPS-' ~ capabilities.ht.smps | upper ~ ']' %} {% endif %} - {% if capabilities.ht.channel_set_width is vyos_defined %} {% for csw in capabilities.ht.channel_set_width %} {% set output.value = output.value ~ '[' ~ csw | upper ~ ']' %} {% endfor %} {% endif %} - {% if capabilities.ht.short_gi is vyos_defined %} {% for short_gi in capabilities.ht.short_gi %} {% set output.value = output.value ~ '[SHORT-GI-' ~ short_gi | upper ~ ']' %} {% endfor %} {% endif %} - ht_capab={{ output.value }} - {% if capabilities.ht.auto_powersave is vyos_defined %} -# WMM-PS Unscheduled Automatic Power Save Delivery [U-APSD] -# Enable this flag if U-APSD supported outside hostapd (eg., Firmware/driver) uapsd_advertisement_enabled=1 {% endif %} {% endif %} - -# Required for full HT and VHT functionality +{% if capabilities.require_ht is vyos_defined %} +require_ht=1 +{% endif %} +{# VHT (802.11ac 5GHz) #} +{% if capabilities.vht is vyos_defined %} +{% if capabilities.vht.center_channel_freq.freq_1 is vyos_defined %} +vht_oper_centr_freq_seg0_idx={{ capabilities.vht.center_channel_freq.freq_1 }} +{% endif %} +{% if capabilities.vht.center_channel_freq.freq_2 is vyos_defined %} +vht_oper_centr_freq_seg1_idx={{ capabilities.vht.center_channel_freq.freq_2 }} +{% endif %} +{% if capabilities.vht.channel_set_width is vyos_defined %} +vht_oper_chwidth={{ capabilities.vht.channel_set_width }} +{% endif %} +{% set output = namespace(value='') %} +{% if capabilities.vht.channel_set_width is vyos_defined('2') %} +{% set output.value = output.value ~ '[VHT160]' %} +{% elif capabilities.vht.channel_set_width is vyos_defined('3') %} +{% set output.value = output.value ~ '[VHT160-80PLUS80]' %} +{% endif %} +{% if capabilities.vht.stbc.tx is vyos_defined %} +{% set output.value = output.value ~ '[TX-STBC-2BY1]' %} +{% endif %} +{% if capabilities.vht.stbc.rx is vyos_defined %} +{% set output.value = output.value ~ '[RX-STBC-' ~ capabilities.vht.stbc.rx ~ ']' %} +{% endif %} +{% if capabilities.vht.ldpc is vyos_defined %} +{% set output.value = output.value ~ '[RXLDPC]' %} +{% endif %} +{% if capabilities.vht.tx_powersave is vyos_defined %} +{% set output.value = output.value ~ '[VHT-TXOP-PS]' %} +{% endif %} +{% if capabilities.vht.vht_cf is vyos_defined %} +{% set output.value = output.value ~ '[HTC-VHT]' %} +{% endif %} +{% if capabilities.vht.antenna_pattern_fixed is vyos_defined %} +{% set output.value = output.value ~ '[RX-ANTENNA-PATTERN][TX-ANTENNA-PATTERN]' %} +{% endif %} +{% if capabilities.vht.max_mpdu is vyos_defined %} +{% set output.value = output.value ~ '[MAX-MPDU-' ~ capabilities.vht.max_mpdu ~ ']' %} +{% endif %} +{% if capabilities.vht.max_mpdu_exp is vyos_defined %} +{% set output.value = output.value ~ '[MAX-A-MPDU-LEN-EXP-' ~ capabilities.vht.max_mpdu_exp ~ ']' %} +{% endif %} +{% if capabilities.vht.link_adaptation is vyos_defined('unsolicited') %} +{% set output.value = output.value ~ '[VHT-LINK-ADAPT2]' %} +{% elif capabilities.vht.link_adaptation is vyos_defined('both') %} +{% set output.value = output.value ~ '[VHT-LINK-ADAPT3]' %} +{% endif %} +{% for short_gi in capabilities.vht.short_gi if capabilities.vht.short_gi is vyos_defined %} +{% set output.value = output.value ~ '[SHORT-GI-' ~ short_gi | upper ~ ']' %} +{% endfor %} +{% if capabilities.vht.beamform is vyos_defined %} +{% for bf in capabilities.vht.beamform %} +{% set output.value = output.value ~ '[SU-BEAMFORMER]' if bf is vyos_defined('single-user-beamformer') else output.value %} +{% set output.value = output.value ~ '[SU-BEAMFORMEE]' if bf is vyos_defined('single-user-beamformee') else output.value %} +{% set output.value = output.value ~ '[MU-BEAMFORMER]' if bf is vyos_defined('multi-user-beamformer') else output.value %} +{% set output.value = output.value ~ '[MU-BEAMFORMEE]' if bf is vyos_defined('multi-user-beamformee') else output.value %} +{% endfor %} +{% if capabilities.vht.antenna_count is vyos_defined and capabilities.vht.antenna_count | int > 1 %} +{% if 'single-user-beamformer' in capabilities.vht.beamform %} +{% if capabilities.vht.antenna_count is vyos_defined and capabilities.vht.antenna_count | int > 1 and capabilities.vht.antenna_count | int < 6 %} +{% set dimension = capabilities.vht.antenna_count | int - 1 %} +{% set output.value = output.value ~ '[BF-ANTENNA-' ~ dimension ~ ']' %} +{% set output.value = output.value ~ '[SOUNDING-DIMENSION-' ~ dimension ~ ']' %} +{% endif %} +{% else %} +{% if capabilities.vht.antenna_count is vyos_defined and capabilities.vht.antenna_count | int > 1 and capabilities.vht.antenna_count | int < 5 %} +{% set output.value = output.value ~ '[BF-ANTENNA-' ~ capabilities.vht.antenna_count ~ ']' %} +{% set output.value = output.value ~ '[SOUNDING-DIMENSION-' ~ capabilities.vht.antenna_count ~ ']' %} +{% endif %} +{% endif %} +{% endif %} +{% endif %} +vht_capab={{ output.value }} +{% endif %} +{# TODO: Research if require_(ht|vht|he) are mutually exclusive! #} +{% if capabilities.require_vht is vyos_defined or capabilities.require_he is vyos_defined %} +{% if capabilities.require_vht is vyos_defined %} +ieee80211n=0 +require_vht=1 +{% endif %} +{% if capabilities.require_he is vyos_defined %} +ieee80211n=0 +require_he=1 +{% endif %} +{% else %} +ieee80211n={{ '1' if 'n' in mode or 'ac' in mode or 'ax' in mode else '0' }} +{% endif %} +{# HE (802.11ax 6GHz) #} +{% if capabilities.he is vyos_defined and mode in 'ax' %} +{# For now, hard-code power levels for indoor-only AP #} +he_6ghz_reg_pwr_type=0 +{# If we had an option to set indoor/outdoor/all environments for a reg domain, we would need to configure the country3 value as well! #} +{# country3=0x4f #} +{% if capabilities.he.center_channel_freq.freq_1 is vyos_defined %} +he_oper_centr_freq_seg0_idx={{ capabilities.he.center_channel_freq.freq_1 }} +{% endif %} +{% if capabilities.he.center_channel_freq.freq_2 is vyos_defined %} +he_oper_centr_freq_seg1_idx={{ capabilities.he.center_channel_freq.freq_2 }} +{% endif %} +{% if capabilities.he.channel_set_width is vyos_defined %} +op_class={{ capabilities.he.channel_set_width }} +{% endif %} +{% if capabilities.he.bss_color is vyos_defined %} +he_bss_color={{ capabilities.he.bss_color }} +{% endif %} +he_6ghz_rx_ant_pat={{ '1' if capabilities.he.antenna_pattern_fixed is vyos_defined else '0' }} +he_su_beamformer={{ '1' if capabilities.he.beamform.single_user_beamformer is vyos_defined else '0' }} +he_su_beamformee={{ '1' if capabilities.he.beamform.single_user_beamformee is vyos_defined else '0' }} +he_mu_beamformer={{ '1' if capabilities.he.beamform.multi_user_beamformer is vyos_defined else '0' }} +{% endif %} +{# generic stuff #} +{% if disable_broadcast_ssid is vyos_defined %} +ignore_broadcast_ssid=1 +{% endif %} +{% if type is vyos_defined('access-point') %} +macaddr_acl={{ '0' if security.station_address.mode is vyos_defined('accept') else '1' }} +accept_mac_file={{ hostapd_accept_station_conf }} +deny_mac_file={{ hostapd_deny_station_conf }} +{% endif %} +{% if stationary_ap is vyos_defined %} +stationary_ap=1 +{% endif %} +{% if max_stations is vyos_defined %} +max_num_sta={{ max_stations }} +{% endif %} +{% if isolate_stations is vyos_defined %} +ap_isolate=1 +{% endif %} +{# enable_background_radar not yet supported by VyOS's version of hostapd +{% if background_radar_detection is vyos_defined %} +enable_background_radar=1 +{% endif %} + #} +{% if reduce_transmit_power is vyos_defined %} +local_pwr_constraint={{ reduce_transmit_power }} +{% endif %} +{% if expunge_failing_stations is vyos_defined %} +disassoc_low_ack=1 +{% endif %} +{% if security.wep is vyos_defined %} +auth_algs=2 +wep_key_len_broadcast=5 +wep_key_len_unicast=5 +wep_default_key=0 +{% if security.wep.key is vyos_defined %} +{% for key in sec_wep_key %} +wep_key{{ loop.index -1 }}={{ security.wep.key }} +{% endfor %} +{% endif %} +{% elif security.wpa is vyos_defined %} +auth_algs=1 +{% if security.wpa.mode is vyos_defined('wpa+wpa2') %} +wpa=3 +{% elif security.wpa.mode is vyos_defined('wpa2') or security.wpa.mode is vyos_defined('wpa3') %} +wpa=2 +{% elif security.wpa.mode is vyos_defined('wpa') %} +wpa=1 +{% endif %} +{% if security.wpa.cipher is vyos_defined %} +{% if security.wpa.mode is vyos_defined('wpa2') or security.wpa.mode is vyos_defined('wpa3') %} +rsn_pairwise={{ security.wpa.cipher | join(" ") }} +{% else %} +wpa_pairwise={{ security.wpa.cipher | join(" ") }} +{% endif %} +{% endif %} +{% if security.wpa.group_cipher is vyos_defined %} +group_cipher={{ security.wpa.group_cipher }} +{% endif %} +{% if security.wpa.group_mgmt_cipher is vyos_defined %} +group_mgmt_cipher={{ security.wpa.group_mgmt_cipher }} +{% endif %} +{% if security.wpa.passphrase is vyos_defined %} +{% if security.wpa.mode is vyos_defined('wpa3') %} +wpa_key_mgmt=SAE +sae_password={{ security.wpa.passphrase }} +extended_key_id=1 +wpa_gmk_rekey=86400 +wpa_group_rekey=86400 +wpa_group_update_count=4 +{% else %} +wpa_key_mgmt=WPA-PSK WPA-PSK-SHA256 +wpa_passphrase={{ security.wpa.passphrase }} +{% endif %} +{% elif security.wpa.radius is vyos_defined %} +ieee8021x=1 +{% if security.wpa.mode is vyos_defined('wpa3') %} +wpa_key_mgmt=WPA-EAP-SUITE-B-192 +{% else %} +wpa_key_mgmt=WPA-EAP WPA-EAP-SHA256 +{% endif %} +{% if security.wpa.radius.server is vyos_defined %} +{% if security.wpa.radius.source_address is vyos_defined %} +radius_client_addr={{ security.wpa.radius.source_address }} +own_ip_addr={{ security.wpa.radius.source_address }} +{% else %} +own_ip_addr=127.0.0.1 +{% endif %} +{% for radius in security.wpa.radius.server if not radius.disabled %} +auth_server_addr={{ radius.server }} +auth_server_port={{ radius.port }} +auth_server_shared_secret={{ radius.key }} +{% if radius.acc_port %} +acct_server_addr={{ radius.server }} +acct_server_port={{ radius.acc_port }} +acct_server_shared_secret={{ radius.key }} +{% endif %} +{% endfor %} +{% else %} +auth_algs=1 +{% endif %} +{% endif %} +{% endif %} +tx_queue_data3_aifs=7 +tx_queue_data3_cwmin=15 +tx_queue_data3_cwmax=1023 +tx_queue_data3_burst=0 +tx_queue_data2_aifs=3 +tx_queue_data2_cwmin=15 +tx_queue_data2_cwmax=63 +tx_queue_data2_burst=0 +tx_queue_data1_aifs=1 +tx_queue_data1_cwmin=7 +tx_queue_data1_cwmax=15 +tx_queue_data1_burst=3.0 +tx_queue_data0_aifs=1 +tx_queue_data0_cwmin=3 +tx_queue_data0_cwmax=7 +tx_queue_data0_burst=1.5 wme_enabled=1 +wmm_enabled=1 +wmm_ac_bk_cwmin=4 +wmm_ac_bk_cwmax=10 +wmm_ac_bk_aifs=7 +wmm_ac_bk_txop_limit=0 +wmm_ac_bk_acm=0 +wmm_ac_be_aifs=3 +wmm_ac_be_cwmin=4 +wmm_ac_be_cwmax=10 +wmm_ac_be_txop_limit=0 +wmm_ac_be_acm=0 +wmm_ac_vi_aifs=2 +wmm_ac_vi_cwmin=3 +wmm_ac_vi_cwmax=4 +wmm_ac_vi_txop_limit=94 +wmm_ac_vi_acm=0 +wmm_ac_vo_aifs=2 +wmm_ac_vo_cwmin=2 +wmm_ac_vo_cwmax=3 +wmm_ac_vo_txop_limit=47 +wmm_ac_vo_acm=0 +{# +# hostapd.conf for hostapd 2.10 +# hostapd.conf reference: +# https://w1.fi/cgit/hostap/tree/hostapd/hostapd.conf?h=hostap_2_10&id=cff80b4f7d3c0a47c052e8187d671710f48939e4 + +##### hostapd configuration file ############################################## +# Empty lines and lines starting with # are ignored + +# AP netdevice name (without 'ap' postfix, i.e., wlan0 uses wlan0ap for +# management frames with the Host AP driver); wlan0 with many nl80211 drivers +# Note: This attribute can be overridden by the values supplied with the '-i' +# command line parameter. +interface=wlan0 + +# In case of atheros and nl80211 driver interfaces, an additional +# configuration parameter, bridge, may be used to notify hostapd if the +# interface is included in a bridge. This parameter is not used with Host AP +# driver. If the bridge parameter is not set, the drivers will automatically +# figure out the bridge interface (assuming sysfs is enabled and mounted to +# /sys) and this parameter may not be needed. +# +# For nl80211, this parameter can be used to request the AP interface to be +# added to the bridge automatically (brctl may refuse to do this before hostapd +# has been started to change the interface mode). If needed, the bridge +# interface is also created. +#bridge=br0 + +# Driver interface type (hostap/wired/none/nl80211/bsd); +# default: hostap). nl80211 is used with all Linux mac80211 drivers. +# Use driver=none if building hostapd as a standalone RADIUS server that does +# not control any wireless/wired driver. +# driver=hostap + +# Driver interface parameters (mainly for development testing use) +# driver_params=<params> + +# hostapd event logger configuration +# +# Two output method: syslog and stdout (only usable if not forking to +# background). +# +# Module bitfield (ORed bitfield of modules that will be logged; -1 = all +# modules): +# bit 0 (1) = IEEE 802.11 +# bit 1 (2) = IEEE 802.1X +# bit 2 (4) = RADIUS +# bit 3 (8) = WPA +# bit 4 (16) = driver interface +# bit 6 (64) = MLME +# +# Levels (minimum value for logged events): +# 0 = verbose debugging +# 1 = debugging +# 2 = informational messages +# 3 = notification +# 4 = warning +# +logger_syslog=-1 +logger_syslog_level=2 +logger_stdout=-1 +logger_stdout_level=2 + +# Interface for separate control program. If this is specified, hostapd +# will create this directory and a UNIX domain socket for listening to requests +# from external programs (CLI/GUI, etc.) for status information and +# configuration. The socket file will be named based on the interface name, so +# multiple hostapd processes/interfaces can be run at the same time if more +# than one interface is used. +# /var/run/hostapd is the recommended directory for sockets and by default, +# hostapd_cli will use it when trying to connect with hostapd. +ctrl_interface=/var/run/hostapd + +# Access control for the control interface can be configured by setting the +# directory to allow only members of a group to use sockets. This way, it is +# possible to run hostapd as root (since it needs to change network +# configuration and open raw sockets) and still allow GUI/CLI components to be +# run as non-root users. However, since the control interface can be used to +# change the network configuration, this access needs to be protected in many +# cases. By default, hostapd is configured to use gid 0 (root). If you +# want to allow non-root users to use the control interface, add a new group +# and change this value to match with that group. Add users that should have +# control interface access to this group. +# +# This variable can be a group name or gid. +#ctrl_interface_group=wheel +ctrl_interface_group=0 + + +##### IEEE 802.11 related configuration ####################################### + +# SSID to be used in IEEE 802.11 management frames +ssid=test +# Alternative formats for configuring SSID +# (double quoted string, hexdump, printf-escaped string) +#ssid2="test" +#ssid2=74657374 +#ssid2=P"hello\nthere" + +# UTF-8 SSID: Whether the SSID is to be interpreted using UTF-8 encoding +#utf8_ssid=1 + +# Country code (ISO/IEC 3166-1). Used to set regulatory domain. +# Set as needed to indicate country in which device is operating. +# This can limit available channels and transmit power. +# These two octets are used as the first two octets of the Country String +# (dot11CountryString) +#country_code=US + +# The third octet of the Country String (dot11CountryString) +# This parameter is used to set the third octet of the country string. +# +# All environments of the current frequency band and country (default) +#country3=0x20 +# Outdoor environment only +#country3=0x4f +# Indoor environment only +#country3=0x49 +# Noncountry entity (country_code=XX) +#country3=0x58 +# IEEE 802.11 standard Annex E table indication: 0x01 .. 0x1f +# Annex E, Table E-4 (Global operating classes) +#country3=0x04 + +# Enable IEEE 802.11d. This advertises the country_code and the set of allowed +# channels and transmit power levels based on the regulatory limits. The +# country_code setting must be configured with the correct country for +# IEEE 802.11d functions. +# (default: 0 = disabled) +#ieee80211d=1 + +# Enable IEEE 802.11h. This enables radar detection and DFS support if +# available. DFS support is required on outdoor 5 GHz channels in most countries +# of the world. This can be used only with ieee80211d=1. +# (default: 0 = disabled) +#ieee80211h=1 + +# Add Power Constraint element to Beacon and Probe Response frames +# This config option adds Power Constraint element when applicable and Country +# element is added. Power Constraint element is required by Transmit Power +# Control. This can be used only with ieee80211d=1. +# Valid values are 0..255. +#local_pwr_constraint=3 + +# Set Spectrum Management subfield in the Capability Information field. +# This config option forces the Spectrum Management bit to be set. When this +# option is not set, the value of the Spectrum Management bit depends on whether +# DFS or TPC is required by regulatory authorities. This can be used only with +# ieee80211d=1 and local_pwr_constraint configured. +#spectrum_mgmt_required=1 + +# Operation mode (a = IEEE 802.11a (5 GHz), b = IEEE 802.11b (2.4 GHz), +# g = IEEE 802.11g (2.4 GHz), ad = IEEE 802.11ad (60 GHz); a/g options are used +# with IEEE 802.11n (HT), too, to specify band). For IEEE 802.11ac (VHT), this +# needs to be set to hw_mode=a. For IEEE 802.11ax (HE) on 6 GHz this needs +# to be set to hw_mode=a. When using ACS (see channel parameter), a +# special value "any" can be used to indicate that any support band can be used. +# This special case is currently supported only with drivers with which +# offloaded ACS is used. +# Default: IEEE 802.11b +hw_mode=g + +# Channel number (IEEE 802.11) +# (default: 0, i.e., not set) +# Please note that some drivers do not use this value from hostapd and the +# channel will need to be configured separately with iwconfig. +# +# If CONFIG_ACS build option is enabled, the channel can be selected +# automatically at run time by setting channel=acs_survey or channel=0, both of +# which will enable the ACS survey based algorithm. +channel=1 + +# Global operating class (IEEE 802.11, Annex E, Table E-4) +# This option allows hostapd to specify the operating class of the channel +# configured with the channel parameter. channel and op_class together can +# uniquely identify channels across different bands, including the 6 GHz band. +#op_class=131 + +# ACS tuning - Automatic Channel Selection +# See: https://wireless.wiki.kernel.org/en/users/documentation/acs +# +# You can customize the ACS survey algorithm with following variables: +# +# acs_num_scans requirement is 1..100 - number of scans to be performed that +# are used to trigger survey data gathering of an underlying device driver. +# Scans are passive and typically take a little over 100ms (depending on the +# driver) on each available channel for given hw_mode. Increasing this value +# means sacrificing startup time and gathering more data wrt channel +# interference that may help choosing a better channel. This can also help fine +# tune the ACS scan time in case a driver has different scan dwell times. +# +# acs_chan_bias is a space-separated list of <channel>:<bias> pairs. It can be +# used to increase (or decrease) the likelihood of a specific channel to be +# selected by the ACS algorithm. The total interference factor for each channel +# gets multiplied by the specified bias value before finding the channel with +# the lowest value. In other words, values between 0.0 and 1.0 can be used to +# make a channel more likely to be picked while values larger than 1.0 make the +# specified channel less likely to be picked. This can be used, e.g., to prefer +# the commonly used 2.4 GHz band channels 1, 6, and 11 (which is the default +# behavior on 2.4 GHz band if no acs_chan_bias parameter is specified). +# +# Defaults: +#acs_num_scans=5 +#acs_chan_bias=1:0.8 6:0.8 11:0.8 + +# Channel list restriction. This option allows hostapd to select one of the +# provided channels when a channel should be automatically selected. +# Channel list can be provided as range using hyphen ('-') or individual +# channels can be specified by space (' ') separated values +# Default: all channels allowed in selected hw_mode +#chanlist=100 104 108 112 116 +#chanlist=1 6 11-13 + +# Frequency list restriction. This option allows hostapd to select one of the +# provided frequencies when a frequency should be automatically selected. +# Frequency list can be provided as range using hyphen ('-') or individual +# frequencies can be specified by comma (',') separated values +# Default: all frequencies allowed in selected hw_mode +#freqlist=2437,5955,5975 +#freqlist=2437,5985-6105 + +# Exclude DFS channels from ACS +# This option can be used to exclude all DFS channels from the ACS channel list +# in cases where the driver supports DFS channels. +#acs_exclude_dfs=1 + +# Include only preferred scan channels from 6 GHz band for ACS +# This option can be used to include only preferred scan channels in the 6 GHz +# band. This can be useful in particular for devices that operate only a 6 GHz +# BSS without a collocated 2.4/5 GHz BSS. +# Default behavior is to include all PSC and non-PSC channels. +#acs_exclude_6ghz_non_psc=1 + +# Set minimum permitted max TX power (in dBm) for ACS and DFS channel selection. +# (default 0, i.e., not constraint) +#min_tx_power=20 + +# Beacon interval in kus (1.024 ms) (default: 100; range 15..65535) +beacon_int=100 + +# DTIM (delivery traffic information message) period (range 1..255): +# number of beacons between DTIMs (1 = every beacon includes DTIM element) +# (default: 2) +dtim_period=2 + +# Maximum number of stations allowed in station table. New stations will be +# rejected after the station table is full. IEEE 802.11 has a limit of 2007 +# different association IDs, so this number should not be larger than that. +# (default: 2007) +max_num_sta=255 + +# RTS/CTS threshold; -1 = disabled (default); range -1..65535 +# If this field is not included in hostapd.conf, hostapd will not control +# RTS threshold and 'iwconfig wlan# rts <val>' can be used to set it. +rts_threshold=-1 + +# Fragmentation threshold; -1 = disabled (default); range -1, 256..2346 +# If this field is not included in hostapd.conf, hostapd will not control +# fragmentation threshold and 'iwconfig wlan# frag <val>' can be used to set +# it. +fragm_threshold=-1 + +# Rate configuration +# Default is to enable all rates supported by the hardware. This configuration +# item allows this list be filtered so that only the listed rates will be left +# in the list. If the list is empty, all rates are used. This list can have +# entries that are not in the list of rates the hardware supports (such entries +# are ignored). The entries in this list are in 100 kbps, i.e., 11 Mbps = 110. +# If this item is present, at least one rate have to be matching with the rates +# hardware supports. +# default: use the most common supported rate setting for the selected +# hw_mode (i.e., this line can be removed from configuration file in most +# cases) +#supported_rates=10 20 55 110 60 90 120 180 240 360 480 540 + +# Basic rate set configuration +# List of rates (in 100 kbps) that are included in the basic rate set. +# If this item is not included, usually reasonable default set is used. +#basic_rates=10 20 +#basic_rates=10 20 55 110 +#basic_rates=60 120 240 + +# Beacon frame TX rate configuration +# This sets the TX rate that is used to transmit Beacon frames. If this item is +# not included, the driver default rate (likely lowest rate) is used. +# Legacy (CCK/OFDM rates): +# beacon_rate=<legacy rate in 100 kbps> +# HT: +# beacon_rate=ht:<HT MCS> +# VHT: +# beacon_rate=vht:<VHT MCS> +# HE: +# beacon_rate=he:<HE MCS> +# +# For example, beacon_rate=10 for 1 Mbps or beacon_rate=60 for 6 Mbps (OFDM). +#beacon_rate=10 + +# Short Preamble +# This parameter can be used to enable optional use of short preamble for +# frames sent at 2 Mbps, 5.5 Mbps, and 11 Mbps to improve network performance. +# This applies only to IEEE 802.11b-compatible networks and this should only be +# enabled if the local hardware supports use of short preamble. If any of the +# associated STAs do not support short preamble, use of short preamble will be +# disabled (and enabled when such STAs disassociate) dynamically. +# 0 = do not allow use of short preamble (default) +# 1 = allow use of short preamble +#preamble=1 + +# Station MAC address -based authentication +# Please note that this kind of access control requires a driver that uses +# hostapd to take care of management frame processing and as such, this can be +# used with driver=hostap or driver=nl80211, but not with driver=atheros. +# 0 = accept unless in deny list +# 1 = deny unless in accept list +# 2 = use external RADIUS server (accept/deny lists are searched first) +macaddr_acl=0 + +# Accept/deny lists are read from separate files (containing list of +# MAC addresses, one per line). Use absolute path name to make sure that the +# files can be read on SIGHUP configuration reloads. +#accept_mac_file=/etc/hostapd.accept +#deny_mac_file=/etc/hostapd.deny + +# IEEE 802.11 specifies two authentication algorithms. hostapd can be +# configured to allow both of these or only one. Open system authentication +# should be used with IEEE 802.1X. +# Bit fields of allowed authentication algorithms: +# bit 0 = Open System Authentication +# bit 1 = Shared Key Authentication (requires WEP) +auth_algs=3 + +# Send empty SSID in beacons and ignore probe request frames that do not +# specify full SSID, i.e., require stations to know SSID. +# default: disabled (0) +# 1 = send empty (length=0) SSID in beacon and ignore probe request for +# broadcast SSID +# 2 = clear SSID (ASCII 0), but keep the original length (this may be required +# with some clients that do not support empty SSID) and ignore probe +# requests for broadcast SSID +ignore_broadcast_ssid=0 + +# Do not reply to broadcast Probe Request frames from unassociated STA if there +# is no room for additional stations (max_num_sta). This can be used to +# discourage a STA from trying to associate with this AP if the association +# would be rejected due to maximum STA limit. +# Default: 0 (disabled) +#no_probe_resp_if_max_sta=0 + +# Additional vendor specific elements for Beacon and Probe Response frames +# This parameter can be used to add additional vendor specific element(s) into +# the end of the Beacon and Probe Response frames. The format for these +# element(s) is a hexdump of the raw information elements (id+len+payload for +# one or more elements) +#vendor_elements=dd0411223301 + +# Additional vendor specific elements for (Re)Association Response frames +# This parameter can be used to add additional vendor specific element(s) into +# the end of the (Re)Association Response frames. The format for these +# element(s) is a hexdump of the raw information elements (id+len+payload for +# one or more elements) +#assocresp_elements=dd0411223301 + +# TX queue parameters (EDCF / bursting) +# tx_queue_<queue name>_<param> +# queues: data0, data1, data2, data3 +# (data0 is the highest priority queue) +# parameters: +# aifs: AIFS (default 2) +# cwmin: cwMin (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023, 2047, 4095, 8191, +# 16383, 32767) +# cwmax: cwMax (same values as cwMin, cwMax >= cwMin) +# burst: maximum length (in milliseconds with precision of up to 0.1 ms) for +# bursting +# +# Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e): +# These parameters are used by the access point when transmitting frames +# to the clients. +# +# Low priority / AC_BK = background +#tx_queue_data3_aifs=7 +#tx_queue_data3_cwmin=15 +#tx_queue_data3_cwmax=1023 +#tx_queue_data3_burst=0 +# Note: for IEEE 802.11b mode: cWmin=31 cWmax=1023 burst=0 +# +# Normal priority / AC_BE = best effort +#tx_queue_data2_aifs=3 +#tx_queue_data2_cwmin=15 +#tx_queue_data2_cwmax=63 +#tx_queue_data2_burst=0 +# Note: for IEEE 802.11b mode: cWmin=31 cWmax=127 burst=0 +# +# High priority / AC_VI = video +#tx_queue_data1_aifs=1 +#tx_queue_data1_cwmin=7 +#tx_queue_data1_cwmax=15 +#tx_queue_data1_burst=3.0 +# Note: for IEEE 802.11b mode: cWmin=15 cWmax=31 burst=6.0 +# +# Highest priority / AC_VO = voice +#tx_queue_data0_aifs=1 +#tx_queue_data0_cwmin=3 +#tx_queue_data0_cwmax=7 +#tx_queue_data0_burst=1.5 +# Note: for IEEE 802.11b mode: cWmin=7 cWmax=15 burst=3.3 + +# 802.1D Tag (= UP) to AC mappings +# WMM specifies following mapping of data frames to different ACs. This mapping +# can be configured using Linux QoS/tc and sch_pktpri.o module. +# 802.1D Tag 802.1D Designation Access Category WMM Designation +# 1 BK AC_BK Background +# 2 - AC_BK Background +# 0 BE AC_BE Best Effort +# 3 EE AC_BE Best Effort +# 4 CL AC_VI Video +# 5 VI AC_VI Video +# 6 VO AC_VO Voice +# 7 NC AC_VO Voice +# Data frames with no priority information: AC_BE +# Management frames: AC_VO +# PS-Poll frames: AC_BE + +# Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e): +# for 802.11a or 802.11g networks +# These parameters are sent to WMM clients when they associate. +# The parameters will be used by WMM clients for frames transmitted to the +# access point. +# +# note - txop_limit is in units of 32microseconds +# note - acm is admission control mandatory flag. 0 = admission control not +# required, 1 = mandatory +# note - Here cwMin and cmMax are in exponent form. The actual cw value used +# will be (2^n)-1 where n is the value given here. The allowed range for these +# wmm_ac_??_{cwmin,cwmax} is 0..15 with cwmax >= cwmin. +# +wmm_enabled=1 +# +# WMM-PS Unscheduled Automatic Power Save Delivery [U-APSD] +# Enable this flag if U-APSD supported outside hostapd (eg., Firmware/driver) +#uapsd_advertisement_enabled=1 +# +# Low priority / AC_BK = background +wmm_ac_bk_cwmin=4 +wmm_ac_bk_cwmax=10 +wmm_ac_bk_aifs=7 +wmm_ac_bk_txop_limit=0 +wmm_ac_bk_acm=0 +# Note: for IEEE 802.11b mode: cWmin=5 cWmax=10 +# +# Normal priority / AC_BE = best effort +wmm_ac_be_aifs=3 +wmm_ac_be_cwmin=4 +wmm_ac_be_cwmax=10 +wmm_ac_be_txop_limit=0 +wmm_ac_be_acm=0 +# Note: for IEEE 802.11b mode: cWmin=5 cWmax=7 +# +# High priority / AC_VI = video +wmm_ac_vi_aifs=2 +wmm_ac_vi_cwmin=3 +wmm_ac_vi_cwmax=4 +wmm_ac_vi_txop_limit=94 +wmm_ac_vi_acm=0 +# Note: for IEEE 802.11b mode: cWmin=4 cWmax=5 txop_limit=188 +# +# Highest priority / AC_VO = voice +wmm_ac_vo_aifs=2 +wmm_ac_vo_cwmin=2 +wmm_ac_vo_cwmax=3 +wmm_ac_vo_txop_limit=47 +wmm_ac_vo_acm=0 +# Note: for IEEE 802.11b mode: cWmin=3 cWmax=4 burst=102 + +# Enable Multi-AP functionality +# 0 = disabled (default) +# 1 = AP support backhaul BSS +# 2 = AP support fronthaul BSS +# 3 = AP supports both backhaul BSS and fronthaul BSS +#multi_ap=0 + +# Static WEP key configuration +# +# The key number to use when transmitting. +# It must be between 0 and 3, and the corresponding key must be set. +# default: not set +#wep_default_key=0 +# The WEP keys to use. +# A key may be a quoted string or unquoted hexadecimal digits. +# The key length should be 5, 13, or 16 characters, or 10, 26, or 32 +# digits, depending on whether 40-bit (64-bit), 104-bit (128-bit), or +# 128-bit (152-bit) WEP is used. +# Only the default key must be supplied; the others are optional. +# default: not set +#wep_key0=123456789a +#wep_key1="vwxyz" +#wep_key2=0102030405060708090a0b0c0d +#wep_key3=".2.4.6.8.0.23" + +# Station inactivity limit +# +# If a station does not send anything in ap_max_inactivity seconds, an +# empty data frame is sent to it in order to verify whether it is +# still in range. If this frame is not ACKed, the station will be +# disassociated and then deauthenticated. This feature is used to +# clear station table of old entries when the STAs move out of the +# range. +# +# The station can associate again with the AP if it is still in range; +# this inactivity poll is just used as a nicer way of verifying +# inactivity; i.e., client will not report broken connection because +# disassociation frame is not sent immediately without first polling +# the STA with a data frame. +# default: 300 (i.e., 5 minutes) +#ap_max_inactivity=300 +# +# The inactivity polling can be disabled to disconnect stations based on +# inactivity timeout so that idle stations are more likely to be disconnected +# even if they are still in range of the AP. This can be done by setting +# skip_inactivity_poll to 1 (default 0). +#skip_inactivity_poll=0 + +# Disassociate stations based on excessive transmission failures or other +# indications of connection loss. This depends on the driver capabilities and +# may not be available with all drivers. +#disassoc_low_ack=1 + +# Maximum allowed Listen Interval (how many Beacon periods STAs are allowed to +# remain asleep). Default: 65535 (no limit apart from field size) +#max_listen_interval=100 + +# WDS (4-address frame) mode with per-station virtual interfaces +# (only supported with driver=nl80211) +# This mode allows associated stations to use 4-address frames to allow layer 2 +# bridging to be used. +#wds_sta=1 + +# If bridge parameter is set, the WDS STA interface will be added to the same +# bridge by default. This can be overridden with the wds_bridge parameter to +# use a separate bridge. +#wds_bridge=wds-br0 + +# Start the AP with beaconing disabled by default. +#start_disabled=0 + +# Client isolation can be used to prevent low-level bridging of frames between +# associated stations in the BSS. By default, this bridging is allowed. +#ap_isolate=1 + +# BSS Load update period (in BUs) +# This field is used to enable and configure adding a BSS Load element into +# Beacon and Probe Response frames. +#bss_load_update_period=50 + +# Channel utilization averaging period (in BUs) +# This field is used to enable and configure channel utilization average +# calculation with bss_load_update_period. This should be in multiples of +# bss_load_update_period for more accurate calculation. +#chan_util_avg_period=600 + +# Fixed BSS Load value for testing purposes +# This field can be used to configure hostapd to add a fixed BSS Load element +# into Beacon and Probe Response frames for testing purposes. The format is +# <station count>:<channel utilization>:<available admission capacity> +#bss_load_test=12:80:20000 + +# Multicast to unicast conversion +# Request that the AP will do multicast-to-unicast conversion for ARP, IPv4, and +# IPv6 frames (possibly within 802.1Q). If enabled, such frames are to be sent +# to each station separately, with the DA replaced by their own MAC address +# rather than the group address. +# +# Note that this may break certain expectations of the receiver, such as the +# ability to drop unicast IP packets received within multicast L2 frames, or the +# ability to not send ICMP destination unreachable messages for packets received +# in L2 multicast (which is required, but the receiver can't tell the difference +# if this new option is enabled). +# +# This also doesn't implement the 802.11 DMS (directed multicast service). +# +#multicast_to_unicast=0 + +# Send broadcast Deauthentication frame on AP start/stop +# Default: 1 (enabled) +#broadcast_deauth=1 + +# Get notifications for received Management frames on control interface +# Default: 0 (disabled) +#notify_mgmt_frames=0 + +##### IEEE 802.11n related configuration ###################################### + +# ieee80211n: Whether IEEE 802.11n (HT) is enabled +# 0 = disabled (default) +# 1 = enabled +# Note: You will also need to enable WMM for full HT functionality. +# Note: hw_mode=g (2.4 GHz) and hw_mode=a (5 GHz) is used to specify the band. +#ieee80211n=1 + +# disable_11n: Boolean (0/1) to disable HT for a specific BSS +#disable_11n=0 + +# ht_capab: HT capabilities (list of flags) +# LDPC coding capability: [LDPC] = supported +# Supported channel width set: [HT40-] = both 20 MHz and 40 MHz with secondary +# channel below the primary channel; [HT40+] = both 20 MHz and 40 MHz +# with secondary channel above the primary channel +# (20 MHz only if neither is set) +# Note: There are limits on which channels can be used with HT40- and +# HT40+. Following table shows the channels that may be available for +# HT40- and HT40+ use per IEEE 802.11n Annex J: +# freq HT40- HT40+ +# 2.4 GHz 5-13 1-7 (1-9 in Europe/Japan) +# 5 GHz 40,48,56,64 36,44,52,60 +# (depending on the location, not all of these channels may be available +# for use) +# Please note that 40 MHz channels may switch their primary and secondary +# channels if needed or creation of 40 MHz channel maybe rejected based +# on overlapping BSSes. These changes are done automatically when hostapd +# is setting up the 40 MHz channel. +# HT-greenfield: [GF] (disabled if not set) +# Short GI for 20 MHz: [SHORT-GI-20] (disabled if not set) +# Short GI for 40 MHz: [SHORT-GI-40] (disabled if not set) +# Tx STBC: [TX-STBC] (disabled if not set) +# Rx STBC: [RX-STBC1] (one spatial stream), [RX-STBC12] (one or two spatial +# streams), or [RX-STBC123] (one, two, or three spatial streams); Rx STBC +# disabled if none of these set +# HT-delayed Block Ack: [DELAYED-BA] (disabled if not set) +# Maximum A-MSDU length: [MAX-AMSDU-7935] for 7935 octets (3839 octets if not +# set) +# DSSS/CCK Mode in 40 MHz: [DSSS_CCK-40] = allowed (not allowed if not set) +# 40 MHz intolerant [40-INTOLERANT] (not advertised if not set) +# L-SIG TXOP protection support: [LSIG-TXOP-PROT] (disabled if not set) +#ht_capab=[HT40-][SHORT-GI-20][SHORT-GI-40] -{% if capabilities.require_ht is vyos_defined %} # Require stations to support HT PHY (reject association if they do not) -require_ht=1 -{% endif %} +#require_ht=1 + +# If set non-zero, require stations to perform scans of overlapping +# channels to test for stations which would be affected by 40 MHz traffic. +# This parameter sets the interval in seconds between these scans. Setting this +# to non-zero allows 2.4 GHz band AP to move dynamically to a 40 MHz channel if +# no co-existence issues with neighboring devices are found. +#obss_interval=0 + +##### IEEE 802.11ac related configuration ##################################### + +# ieee80211ac: Whether IEEE 802.11ac (VHT) is enabled +# 0 = disabled (default) +# 1 = enabled +# Note: You will also need to enable WMM for full VHT functionality. +# Note: hw_mode=a is used to specify that 5 GHz band is used with VHT. +#ieee80211ac=1 + +# disable_11ac: Boolean (0/1) to disable VHT for a specific BSS +#disable_11ac=0 -{% if capabilities.vht is vyos_defined %} # vht_capab: VHT capabilities (list of flags) # # vht_max_mpdu_len: [MAX-MPDU-7991] [MAX-MPDU-11454] @@ -304,7 +1116,7 @@ require_ht=1 # Indicates the maximum length of A-MPDU pre-EOF padding that the STA can recv # This field is an integer in the range of 0 to 7. # The length defined by this field is equal to -# 2 pow(13 ~ Maximum A-MPDU Length Exponent) -1 octets +# 2 pow(13 + Maximum A-MPDU Length Exponent) -1 octets # # VHT Link Adaptation Capable: [VHT-LINK-ADAPT2] [VHT-LINK-ADAPT3] # Indicates whether or not the STA supports link adaptation using VHT variant @@ -325,26 +1137,38 @@ require_ht=1 # Tx Antenna Pattern Consistency: [TX-ANTENNA-PATTERN] # Indicates the possibility of Tx antenna pattern change # 0 = Tx antenna pattern might change during the lifetime of an association -# 1 = Tx antenna pattern does not change during the lifetime of an +# 1 = Tx antenna pattern does not change during the lifetime of an association +#vht_capab=[SHORT-GI-80][HTC-VHT] +# +# Require stations to support VHT PHY (reject association if they do not) +#require_vht=1 -{% if capabilities.vht.center_channel_freq.freq_1 is vyos_defined %} -# center freq = 5 GHz ~ (5 * index) +# 0 = 20 or 40 MHz operating Channel width +# 1 = 80 MHz channel width +# 2 = 160 MHz channel width +# 3 = 80+80 MHz channel width +#vht_oper_chwidth=1 +# +# center freq = 5 GHz + (5 * index) # So index 42 gives center freq 5.210 GHz # which is channel 42 in 5G band -vht_oper_centr_freq_seg0_idx={{ capabilities.vht.center_channel_freq.freq_1 }} -{% endif %} - -{% if capabilities.vht.center_channel_freq.freq_2 is vyos_defined %} -# center freq = 5 GHz ~ (5 * index) +# +#vht_oper_centr_freq_seg0_idx=42 +# +# center freq = 5 GHz + (5 * index) # So index 159 gives center freq 5.795 GHz # which is channel 159 in 5G band -vht_oper_centr_freq_seg1_idx={{ capabilities.vht.center_channel_freq.freq_2 }} -{% endif %} +# +#vht_oper_centr_freq_seg1_idx=159 -{% if capabilities.vht.channel_set_width is vyos_defined %} -vht_oper_chwidth={{ capabilities.vht.channel_set_width }} -{% endif %} +# Workaround to use station's nsts capability in (Re)Association Response frame +# This may be needed with some deployed devices as an interoperability +# workaround for beamforming if the AP's capability is greater than the +# station's capability. This is disabled by default and can be enabled by +# setting use_sta_nsts=1. +#use_sta_nsts=0 +<<<<<<< HEAD {% set output = namespace(value='') %} {% if capabilities.vht.channel_set_width is vyos_defined('2') %} {% set output.value = output.value ~ '[VHT160]' %} @@ -403,120 +1227,819 @@ vht_oper_chwidth={{ capabilities.vht.channel_set_width }} {% endif %} {% endif %} {% endif %} +======= +##### IEEE 802.11ax related configuration ##################################### +>>>>>>> d5e988ba2 (wireless: T6320: add 802.11ax at 6GHz) -vht_capab={{ output.value }} -{% endif %} - -# ieee80211n: Whether IEEE 802.11n (HT) is enabled +#ieee80211ax: Whether IEEE 802.11ax (HE) is enabled # 0 = disabled (default) # 1 = enabled -# Note: You will also need to enable WMM for full HT functionality. -# Note: hw_mode=g (2.4 GHz) and hw_mode=a (5 GHz) is used to specify the band. -{% if capabilities.require_vht is vyos_defined %} -ieee80211n=0 -# Require stations to support VHT PHY (reject association if they do not) -require_vht=1 -{% else %} -ieee80211n={{ '1' if 'n' in mode or 'ac' in mode else '0' }} -{% endif %} +#ieee80211ax=1 -{% if disable_broadcast_ssid is vyos_defined %} -# Send empty SSID in beacons and ignore probe request frames that do not -# specify full SSID, i.e., require stations to know SSID. -# default: disabled (0) -# 1 = send empty (length=0) SSID in beacon and ignore probe request for -# broadcast SSID -# 2 = clear SSID (ASCII 0), but keep the original length (this may be required -# with some clients that do not support empty SSID) and ignore probe -# requests for broadcast SSID -ignore_broadcast_ssid=1 -{% endif %} +# disable_11ax: Boolean (0/1) to disable HE for a specific BSS +#disable_11ax=0 -{% if type is vyos_defined('access-point') %} -# Station MAC address-based authentication -# Please note that this kind of access control requires a driver that uses -# hostapd to take care of management frame processing and as such, this can be -# used with driver=hostap or driver=nl80211, but not with driver=atheros. -# 0 = accept unless in deny list -# 1 = deny unless in accept list -# 2 = use external RADIUS server (accept/deny lists are searched first) -macaddr_acl={{ '0' if security.station_address.mode is vyos_defined('accept') else '1' }} +#he_su_beamformer: HE single user beamformer support +# 0 = not supported (default) +# 1 = supported +#he_su_beamformer=1 -# Accept/deny lists are read from separate files (containing list of -# MAC addresses, one per line). Use absolute path name to make sure that the -# files can be read on SIGHUP configuration reloads. -accept_mac_file={{ hostapd_accept_station_conf }} -deny_mac_file={{ hostapd_deny_station_conf }} -{% endif %} +#he_su_beamformee: HE single user beamformee support +# 0 = not supported (default) +# 1 = supported +#he_su_beamformee=1 -{% if max_stations is vyos_defined %} -# Maximum number of stations allowed in station table. New stations will be -# rejected after the station table is full. IEEE 802.11 has a limit of 2007 -# different association IDs, so this number should not be larger than that. -# (default: 2007) -max_num_sta={{ max_stations }} -{% endif %} +#he_mu_beamformer: HE multiple user beamformer support +# 0 = not supported (default) +# 1 = supported +#he_mu_beamformer=1 -{% if isolate_stations is vyos_defined %} -# Client isolation can be used to prevent low-level bridging of frames between -# associated stations in the BSS. By default, this bridging is allowed. -ap_isolate=1 -{% endif %} +# he_bss_color: BSS color (1-63) +#he_bss_color=1 -{% if reduce_transmit_power is vyos_defined %} -# Add Power Constraint element to Beacon and Probe Response frames -# This config option adds Power Constraint element when applicable and Country -# element is added. Power Constraint element is required by Transmit Power -# Control. This can be used only with ieee80211d=1. -# Valid values are 0..255. -local_pwr_constraint={{ reduce_transmit_power }} -{% endif %} +# he_bss_color_partial: BSS color AID equation +#he_bss_color_partial=0 -{% if expunge_failing_stations is vyos_defined %} -# Disassociate stations based on excessive transmission failures or other -# indications of connection loss. This depends on the driver capabilities and -# may not be available with all drivers. -disassoc_low_ack=1 -{% endif %} +#he_default_pe_duration: The duration of PE field in an HE PPDU in us +# Possible values are 0 us (default), 4 us, 8 us, 12 us, and 16 us +#he_default_pe_duration=0 +#he_twt_required: Whether TWT is required +# 0 = not required (default) +# 1 = required +#he_twt_required=0 -{% if security.wep is vyos_defined %} -# IEEE 802.11 specifies two authentication algorithms. hostapd can be -# configured to allow both of these or only one. Open system authentication -# should be used with IEEE 802.1X. -# Bit fields of allowed authentication algorithms: -# bit 0 = Open System Authentication -# bit 1 = Shared Key Authentication (requires WEP) -auth_algs=2 +#he_twt_responder: Whether TWT (HE) responder is enabled +# 0 = disabled +# 1 = enabled if supported by the driver (default) +#he_twt_responder=1 + +#he_rts_threshold: Duration of STA transmission +# 0 = not set (default) +# unsigned integer = duration in units of 16 us +#he_rts_threshold=0 + +#he_er_su_disable: Disable 242-tone HE ER SU PPDU reception by the AP +# 0 = enable reception (default) +# 1 = disable reception +#he_er_su_disable=0 + +# HE operating channel information; see matching vht_* parameters for details. +# he_oper_centr_freq_seg0_idx field is used to indicate center frequency of 80 +# and 160 MHz bandwidth operation. In 80+80 MHz operation, it is the center +# frequency of the lower frequency segment. he_oper_centr_freq_seg1_idx field +# is used only with 80+80 MHz bandwidth operation and it is used to transmit +# the center frequency of the second segment. +# On the 6 GHz band the center freq calculation starts from 5.950 GHz offset. +# For example idx=3 would result in 5965 MHz center frequency. In addition, +# he_oper_chwidth is ignored, and the channel width is derived from the +# configured operating class or center frequency indexes (see +# IEEE P802.11ax/D6.1 Annex E, Table E-4). +#he_oper_chwidth +#he_oper_centr_freq_seg0_idx +#he_oper_centr_freq_seg1_idx + +#he_basic_mcs_nss_set: Basic NSS/MCS set +# 16-bit combination of 2-bit values of Max HE-MCS For 1..8 SS; each 2-bit +# value having following meaning: +# 0 = HE-MCS 0-7, 1 = HE-MCS 0-9, 2 = HE-MCS 0-11, 3 = not supported +#he_basic_mcs_nss_set + +#he_mu_edca_qos_info_param_count +#he_mu_edca_qos_info_q_ack +#he_mu_edca_qos_info_queue_request=1 +#he_mu_edca_qos_info_txop_request +#he_mu_edca_ac_be_aifsn=0 +#he_mu_edca_ac_be_ecwmin=15 +#he_mu_edca_ac_be_ecwmax=15 +#he_mu_edca_ac_be_timer=255 +#he_mu_edca_ac_bk_aifsn=0 +#he_mu_edca_ac_bk_aci=1 +#he_mu_edca_ac_bk_ecwmin=15 +#he_mu_edca_ac_bk_ecwmax=15 +#he_mu_edca_ac_bk_timer=255 +#he_mu_edca_ac_vi_ecwmin=15 +#he_mu_edca_ac_vi_ecwmax=15 +#he_mu_edca_ac_vi_aifsn=0 +#he_mu_edca_ac_vi_aci=2 +#he_mu_edca_ac_vi_timer=255 +#he_mu_edca_ac_vo_aifsn=0 +#he_mu_edca_ac_vo_aci=3 +#he_mu_edca_ac_vo_ecwmin=15 +#he_mu_edca_ac_vo_ecwmax=15 +#he_mu_edca_ac_vo_timer=255 + +# Spatial Reuse Parameter Set +# +# SR Control field value +# B0 = PSR Disallowed +# B1 = Non-SRG OBSS PD SR Disallowed +# B2 = Non-SRG Offset Present +# B3 = SRG Information Present +# B4 = HESIGA_Spatial_reuse_value15_allowed +#he_spr_sr_control +# +# Non-SRG OBSS PD Max Offset (included if he_spr_sr_control B2=1) +#he_spr_non_srg_obss_pd_max_offset + +# SRG OBSS PD Min Offset (included if he_spr_sr_control B3=1) +#he_spr_srg_obss_pd_min_offset +# +# SRG OBSS PD Max Offset (included if he_spr_sr_control B3=1) +#he_spr_srg_obss_pd_max_offset +# +# SPR SRG BSS Color (included if he_spr_sr_control B3=1) +# This config represents SRG BSS Color Bitmap field of Spatial Reuse Parameter +# Set element that indicates the BSS color values used by members of the +# SRG of which the transmitting STA is a member. The value is in range of 0-63. +#he_spr_srg_bss_colors=1 2 10 63 +# +# SPR SRG Partial BSSID (included if he_spr_sr_control B3=1) +# This config represents SRG Partial BSSID Bitmap field of Spatial Reuse +# Parameter Set element that indicates the Partial BSSID values used by members +# of the SRG of which the transmitting STA is a member. The value range +# corresponds to one of the 64 possible values of BSSID[39:44], where the lowest +# numbered bit corresponds to Partial BSSID value 0 and the highest numbered bit +# corresponds to Partial BSSID value 63. +#he_spr_srg_partial_bssid=0 1 3 63 +# +#he_6ghz_max_mpdu: Maximum MPDU Length of HE 6 GHz band capabilities. +# Indicates maximum MPDU length +# 0 = 3895 octets +# 1 = 7991 octets +# 2 = 11454 octets (default) +#he_6ghz_max_mpdu=2 +# +#he_6ghz_max_ampdu_len_exp: Maximum A-MPDU Length Exponent of HE 6 GHz band +# capabilities. Indicates the maximum length of A-MPDU pre-EOF padding that +# the STA can receive. This field is an integer in the range of 0 to 7. +# The length defined by this field is equal to +# 2 pow(13 + Maximum A-MPDU Length Exponent) -1 octets +# 0 = AMPDU length of 8k +# 1 = AMPDU length of 16k +# 2 = AMPDU length of 32k +# 3 = AMPDU length of 65k +# 4 = AMPDU length of 131k +# 5 = AMPDU length of 262k +# 6 = AMPDU length of 524k +# 7 = AMPDU length of 1048k (default) +#he_6ghz_max_ampdu_len_exp=7 +# +#he_6ghz_rx_ant_pat: Rx Antenna Pattern Consistency of HE 6 GHz capability. +# Indicates the possibility of Rx antenna pattern change +# 0 = Rx antenna pattern might change during the lifetime of an association +# 1 = Rx antenna pattern does not change during the lifetime of an association +# (default) +#he_6ghz_rx_ant_pat=1 +# +#he_6ghz_tx_ant_pat: Tx Antenna Pattern Consistency of HE 6 GHz capability. +# Indicates the possibility of Tx antenna pattern change +# 0 = Tx antenna pattern might change during the lifetime of an association +# 1 = Tx antenna pattern does not change during the lifetime of an association +# (default) +#he_6ghz_tx_ant_pat=1 + +# Unsolicited broadcast Probe Response transmission settings +# This is for the 6 GHz band only. If the interval is set to a non-zero value, +# the AP schedules unsolicited broadcast Probe Response frames to be +# transmitted for in-band discovery. Refer to +# IEEE P802.11ax/D8.0 26.17.2.3.2, AP behavior for fast passive scanning. +# Valid range: 0..20 TUs; default is 0 (disabled) +#unsol_bcast_probe_resp_interval=0 + +##### IEEE 802.1X-2004 related configuration ################################## + +# Require IEEE 802.1X authorization +#ieee8021x=1 + +# IEEE 802.1X/EAPOL version +# hostapd is implemented based on IEEE Std 802.1X-2004 which defines EAPOL +# version 2. However, there are many client implementations that do not handle +# the new version number correctly (they seem to drop the frames completely). +# In order to make hostapd interoperate with these clients, the version number +# can be set to the older version (1) with this configuration value. +# Note: When using MACsec, eapol_version shall be set to 3, which is +# defined in IEEE Std 802.1X-2010. +#eapol_version=2 + +# Optional displayable message sent with EAP Request-Identity. The first \0 +# in this string will be converted to ASCII-0 (nul). This can be used to +# separate network info (comma separated list of attribute=value pairs); see, +# e.g., RFC 4284. +#eap_message=hello +#eap_message=hello\0networkid=netw,nasid=foo,portid=0,NAIRealms=example.com # WEP rekeying (disabled if key lengths are not set or are set to 0) # Key lengths for default/broadcast and individual/unicast keys: # 5 = 40-bit WEP (also known as 64-bit WEP with 40 secret bits) # 13 = 104-bit WEP (also known as 128-bit WEP with 104 secret bits) -wep_key_len_broadcast=5 -wep_key_len_unicast=5 +#wep_key_len_broadcast=5 +#wep_key_len_unicast=5 +# Rekeying period in seconds. 0 = do not rekey (i.e., set keys only once) +#wep_rekey_period=300 -# Static WEP key configuration +# EAPOL-Key index workaround (set bit7) for WinXP Supplicant (needed only if +# only broadcast keys are used) +eapol_key_index_workaround=0 + +# EAP reauthentication period in seconds (default: 3600 seconds; 0 = disable +# reauthentication). +# Note: Reauthentications may enforce a disconnection, check the related +# parameter wpa_deny_ptk0_rekey for details. +#eap_reauth_period=3600 + +# Use PAE group address (01:80:c2:00:00:03) instead of individual target +# address when sending EAPOL frames with driver=wired. This is the most common +# mechanism used in wired authentication, but it also requires that the port +# is only used by one station. +#use_pae_group_addr=1 + +# EAP Re-authentication Protocol (ERP) authenticator (RFC 6696) # -# The key number to use when transmitting. -# It must be between 0 and 3, and the corresponding key must be set. -# default: not set -wep_default_key=0 +# Whether to initiate EAP authentication with EAP-Initiate/Re-auth-Start before +# EAP-Identity/Request +#erp_send_reauth_start=1 +# +# Domain name for EAP-Initiate/Re-auth-Start. Omitted from the message if not +# set (no local ER server). This is also used by the integrated EAP server if +# ERP is enabled (eap_server_erp=1). +#erp_domain=example.com -# The WEP keys to use. -# A key may be a quoted string or unquoted hexadecimal digits. -# The key length should be 5, 13, or 16 characters, or 10, 26, or 32 -# digits, depending on whether 40-bit (64-bit), 104-bit (128-bit), or -# 128-bit (152-bit) WEP is used. -# Only the default key must be supplied; the others are optional. -{% if security.wep.key is vyos_defined %} -{% for key in sec_wep_key %} -wep_key{{ loop.index -1 }}={{ security.wep.key }} -{% endfor %} -{% endif %} +##### MACsec ################################################################## + +# macsec_policy: IEEE 802.1X/MACsec options +# This determines how sessions are secured with MACsec (only for MACsec +# drivers). +# 0: MACsec not in use (default) +# 1: MACsec enabled - Should secure, accept key server's advice to +# determine whether to use a secure session or not. +# +# macsec_integ_only: IEEE 802.1X/MACsec transmit mode +# This setting applies only when MACsec is in use, i.e., +# - macsec_policy is enabled +# - the key server has decided to enable MACsec +# 0: Encrypt traffic (default) +# 1: Integrity only +# +# macsec_replay_protect: IEEE 802.1X/MACsec replay protection +# This setting applies only when MACsec is in use, i.e., +# - macsec_policy is enabled +# - the key server has decided to enable MACsec +# 0: Replay protection disabled (default) +# 1: Replay protection enabled +# +# macsec_replay_window: IEEE 802.1X/MACsec replay protection window +# This determines a window in which replay is tolerated, to allow receipt +# of frames that have been misordered by the network. +# This setting applies only when MACsec replay protection active, i.e., +# - macsec_replay_protect is enabled +# - the key server has decided to enable MACsec +# 0: No replay window, strict check (default) +# 1..2^32-1: number of packets that could be misordered +# +# macsec_port: IEEE 802.1X/MACsec port +# Port component of the SCI +# Range: 1-65534 (default: 1) +# +# mka_priority (Priority of MKA Actor) +# Range: 0..255 (default: 255) +# +# mka_cak, mka_ckn, and mka_priority: IEEE 802.1X/MACsec pre-shared key mode +# This allows to configure MACsec with a pre-shared key using a (CAK,CKN) pair. +# In this mode, instances of hostapd can act as MACsec peers. The peer +# with lower priority will become the key server and start distributing SAKs. +# mka_cak (CAK = Secure Connectivity Association Key) takes a 16-byte (128-bit) +# hex-string (32 hex-digits) or a 32-byte (256-bit) hex-string (64 hex-digits) +# mka_ckn (CKN = CAK Name) takes a 1..32-bytes (8..256 bit) hex-string +# (2..64 hex-digits) + +##### Integrated EAP server ################################################### + +# Optionally, hostapd can be configured to use an integrated EAP server +# to process EAP authentication locally without need for an external RADIUS +# server. This functionality can be used both as a local authentication server +# for IEEE 802.1X/EAPOL and as a RADIUS server for other devices. + +# Use integrated EAP server instead of external RADIUS authentication +# server. This is also needed if hostapd is configured to act as a RADIUS +# authentication server. +eap_server=0 + +# Path for EAP server user database +# If SQLite support is included, this can be set to "sqlite:/path/to/sqlite.db" +# to use SQLite database instead of a text file. +#eap_user_file=/etc/hostapd.eap_user + +# CA certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS +#ca_cert=/etc/hostapd.ca.pem + +# Server certificate (PEM or DER file) for EAP-TLS/PEAP/TTLS +#server_cert=/etc/hostapd.server.pem + +# Private key matching with the server certificate for EAP-TLS/PEAP/TTLS +# This may point to the same file as server_cert if both certificate and key +# are included in a single file. PKCS#12 (PFX) file (.p12/.pfx) can also be +# used by commenting out server_cert and specifying the PFX file as the +# private_key. +#private_key=/etc/hostapd.server.prv + +# Passphrase for private key +#private_key_passwd=secret passphrase + +# An alternative server certificate and private key can be configured with the +# following parameters (with values just like the parameters above without the +# '2' suffix). The ca_cert file (in PEM encoding) is used to add the trust roots +# for both server certificates and/or client certificates). +# +# The main use case for this alternative server certificate configuration is to +# enable both RSA and ECC public keys. The server will pick which one to use +# based on the client preferences for the cipher suite (in the TLS ClientHello +# message). It should be noted that number of deployed EAP peer implementations +# do not filter out the cipher suite list based on their local configuration and +# as such, configuration of alternative types of certificates on the server may +# result in interoperability issues. +#server_cert2=/etc/hostapd.server-ecc.pem +#private_key2=/etc/hostapd.server-ecc.prv +#private_key_passwd2=secret passphrase + + +# Server identity +# EAP methods that provide mechanism for authenticated server identity delivery +# use this value. If not set, "hostapd" is used as a default. +#server_id=server.example.com + +# Enable CRL verification. +# Note: hostapd does not yet support CRL downloading based on CDP. Thus, a +# valid CRL signed by the CA is required to be included in the ca_cert file. +# This can be done by using PEM format for CA certificate and CRL and +# concatenating these into one file. Whenever CRL changes, hostapd needs to be +# restarted to take the new CRL into use. Alternatively, crl_reload_interval can +# be used to configure periodic updating of the loaded CRL information. +# 0 = do not verify CRLs (default) +# 1 = check the CRL of the user certificate +# 2 = check all CRLs in the certificate path +#check_crl=1 + +# Specify whether to ignore certificate CRL validity time mismatches with +# errors X509_V_ERR_CRL_HAS_EXPIRED and X509_V_ERR_CRL_NOT_YET_VALID. +# +# 0 = ignore errors +# 1 = do not ignore errors (default) +#check_crl_strict=1 + +# CRL reload interval in seconds +# This can be used to reload ca_cert file and the included CRL on every new TLS +# session if difference between last reload and the current reload time in +# seconds is greater than crl_reload_interval. +# Note: If interval time is very short, CPU overhead may be negatively affected +# and it is advised to not go below 300 seconds. +# This is applicable only with check_crl values 1 and 2. +# 0 = do not reload CRLs (default) +# crl_reload_interval = 300 + +# If check_cert_subject is set, the value of every field will be checked +# against the DN of the subject in the client certificate. If the values do +# not match, the certificate verification will fail, rejecting the user. +# This option allows hostapd to match every individual field in the right order +# against the DN of the subject in the client certificate. +# +# For example, check_cert_subject=C=US/O=XX/OU=ABC/OU=XYZ/CN=1234 will check +# every individual DN field of the subject in the client certificate. If OU=XYZ +# comes first in terms of the order in the client certificate (DN field of +# client certificate C=US/O=XX/OU=XYZ/OU=ABC/CN=1234), hostapd will reject the +# client because the order of 'OU' is not matching the specified string in +# check_cert_subject. +# +# This option also allows '*' as a wildcard. This option has some limitation. +# It can only be used as per the following example. +# +# For example, check_cert_subject=C=US/O=XX/OU=Production* and we have two +# clients and DN of the subject in the first client certificate is +# (C=US/O=XX/OU=Production Unit) and DN of the subject in the second client is +# (C=US/O=XX/OU=Production Factory). In this case, hostapd will allow both +# clients because the value of 'OU' field in both client certificates matches +# 'OU' value in 'check_cert_subject' up to 'wildcard'. +# +# * (Allow all clients, e.g., check_cert_subject=*) +#check_cert_subject=string + +# TLS Session Lifetime in seconds +# This can be used to allow TLS sessions to be cached and resumed with an +# abbreviated handshake when using EAP-TLS/TTLS/PEAP. +# (default: 0 = session caching and resumption disabled) +#tls_session_lifetime=3600 + +# TLS flags +# [ALLOW-SIGN-RSA-MD5] = allow MD5-based certificate signatures (depending on +# the TLS library, these may be disabled by default to enforce stronger +# security) +# [DISABLE-TIME-CHECKS] = ignore certificate validity time (this requests +# the TLS library to accept certificates even if they are not currently +# valid, i.e., have expired or have not yet become valid; this should be +# used only for testing purposes) +# [DISABLE-TLSv1.0] = disable use of TLSv1.0 +# [ENABLE-TLSv1.0] = explicitly enable use of TLSv1.0 (this allows +# systemwide TLS policies to be overridden) +# [DISABLE-TLSv1.1] = disable use of TLSv1.1 +# [ENABLE-TLSv1.1] = explicitly enable use of TLSv1.1 (this allows +# systemwide TLS policies to be overridden) +# [DISABLE-TLSv1.2] = disable use of TLSv1.2 +# [ENABLE-TLSv1.2] = explicitly enable use of TLSv1.2 (this allows +# systemwide TLS policies to be overridden) +# [DISABLE-TLSv1.3] = disable use of TLSv1.3 +# [ENABLE-TLSv1.3] = enable TLSv1.3 (experimental - disabled by default) +#tls_flags=[flag1][flag2]... + +# Maximum number of EAP message rounds with data (default: 100) +#max_auth_rounds=100 + +# Maximum number of short EAP message rounds (default: 50) +#max_auth_rounds_short=50 + +# Cached OCSP stapling response (DER encoded) +# If set, this file is sent as a certificate status response by the EAP server +# if the EAP peer requests certificate status in the ClientHello message. +# This cache file can be updated, e.g., by running following command +# periodically to get an update from the OCSP responder: +# openssl ocsp \ +# -no_nonce \ +# -CAfile /etc/hostapd.ca.pem \ +# -issuer /etc/hostapd.ca.pem \ +# -cert /etc/hostapd.server.pem \ +# -url http://ocsp.example.com:8888/ \ +# -respout /tmp/ocsp-cache.der +#ocsp_stapling_response=/tmp/ocsp-cache.der + +# Cached OCSP stapling response list (DER encoded OCSPResponseList) +# This is similar to ocsp_stapling_response, but the extended version defined in +# RFC 6961 to allow multiple OCSP responses to be provided. +#ocsp_stapling_response_multi=/tmp/ocsp-multi-cache.der + +# dh_file: File path to DH/DSA parameters file (in PEM format) +# This is an optional configuration file for setting parameters for an +# ephemeral DH key exchange. In most cases, the default RSA authentication does +# not use this configuration. However, it is possible setup RSA to use +# ephemeral DH key exchange. In addition, ciphers with DSA keys always use +# ephemeral DH keys. This can be used to achieve forward secrecy. If the file +# is in DSA parameters format, it will be automatically converted into DH +# params. This parameter is required if anonymous EAP-FAST is used. +# You can generate DH parameters file with OpenSSL, e.g., +# "openssl dhparam -out /etc/hostapd.dh.pem 2048" +#dh_file=/etc/hostapd.dh.pem + +# OpenSSL cipher string +# +# This is an OpenSSL specific configuration option for configuring the default +# ciphers. If not set, the value configured at build time ("DEFAULT:!EXP:!LOW" +# by default) is used. +# See https://www.openssl.org/docs/apps/ciphers.html for OpenSSL documentation +# on cipher suite configuration. This is applicable only if hostapd is built to +# use OpenSSL. +#openssl_ciphers=DEFAULT:!EXP:!LOW + +# OpenSSL ECDH curves +# +# This is an OpenSSL specific configuration option for configuring the ECDH +# curves for EAP-TLS/TTLS/PEAP/FAST server. If not set, automatic curve +# selection is enabled. If set to an empty string, ECDH curve configuration is +# not done (the exact library behavior depends on the library version). +# Otherwise, this is a colon separated list of the supported curves (e.g., +# P-521:P-384:P-256). This is applicable only if hostapd is built to use +# OpenSSL. This must not be used for Suite B cases since the same OpenSSL +# parameter is set differently in those cases and this might conflict with that +# design. +#openssl_ecdh_curves=P-521:P-384:P-256 + +# Fragment size for EAP methods +#fragment_size=1400 + +# Finite cyclic group for EAP-pwd. Number maps to group of domain parameters +# using the IANA repository for IKE (RFC 2409). +#pwd_group=19 + +# Configuration data for EAP-SIM database/authentication gateway interface. +# This is a text string in implementation specific format. The example +# implementation in eap_sim_db.c uses this as the UNIX domain socket name for +# the HLR/AuC gateway (e.g., hlr_auc_gw). In this case, the path uses "unix:" +# prefix. If hostapd is built with SQLite support (CONFIG_SQLITE=y in .config), +# database file can be described with an optional db=<path> parameter. +#eap_sim_db=unix:/tmp/hlr_auc_gw.sock +#eap_sim_db=unix:/tmp/hlr_auc_gw.sock db=/tmp/hostapd.db + +# EAP-SIM DB request timeout +# This parameter sets the maximum time to wait for a database request response. +# The parameter value is in seconds. +#eap_sim_db_timeout=1 + +# Encryption key for EAP-FAST PAC-Opaque values. This key must be a secret, +# random value. It is configured as a 16-octet value in hex format. It can be +# generated, e.g., with the following command: +# od -tx1 -v -N16 /dev/random | colrm 1 8 | tr -d ' ' +#pac_opaque_encr_key=000102030405060708090a0b0c0d0e0f + +# EAP-FAST authority identity (A-ID) +# A-ID indicates the identity of the authority that issues PACs. The A-ID +# should be unique across all issuing servers. In theory, this is a variable +# length field, but due to some existing implementations requiring A-ID to be +# 16 octets in length, it is strongly recommended to use that length for the +# field to provide interoperability with deployed peer implementations. This +# field is configured in hex format. +#eap_fast_a_id=101112131415161718191a1b1c1d1e1f + +# EAP-FAST authority identifier information (A-ID-Info) +# This is a user-friendly name for the A-ID. For example, the enterprise name +# and server name in a human-readable format. This field is encoded as UTF-8. +#eap_fast_a_id_info=test server + +# Enable/disable different EAP-FAST provisioning modes: +#0 = provisioning disabled +#1 = only anonymous provisioning allowed +#2 = only authenticated provisioning allowed +#3 = both provisioning modes allowed (default) +#eap_fast_prov=3 + +# EAP-FAST PAC-Key lifetime in seconds (hard limit) +#pac_key_lifetime=604800 + +# EAP-FAST PAC-Key refresh time in seconds (soft limit on remaining hard +# limit). The server will generate a new PAC-Key when this number of seconds +# (or fewer) of the lifetime remains. +#pac_key_refresh_time=86400 + +# EAP-TEAP authentication type +# 0 = inner EAP (default) +# 1 = Basic-Password-Auth +# 2 = Do not require Phase 2 authentication if client can be authenticated +# during Phase 1 +#eap_teap_auth=0 + +# EAP-TEAP authentication behavior when using PAC +# 0 = perform inner authentication (default) +# 1 = skip inner authentication (inner EAP/Basic-Password-Auth) +#eap_teap_pac_no_inner=0 + +# EAP-TEAP behavior with Result TLV +# 0 = include with Intermediate-Result TLV (default) +# 1 = send in a separate message (for testing purposes) +#eap_teap_separate_result=0 + +# EAP-TEAP identities +# 0 = allow any identity type (default) +# 1 = require user identity +# 2 = require machine identity +# 3 = request user identity; accept either user or machine identity +# 4 = request machine identity; accept either user or machine identity +# 5 = require both user and machine identity +#eap_teap_id=0 + +# EAP-SIM and EAP-AKA protected success/failure indication using AT_RESULT_IND +# (default: 0 = disabled). +#eap_sim_aka_result_ind=1 + +# EAP-SIM and EAP-AKA identity options +# 0 = do not use pseudonyms or fast reauthentication +# 1 = use pseudonyms, but not fast reauthentication +# 2 = do not use pseudonyms, but use fast reauthentication +# 3 = use pseudonyms and use fast reauthentication (default) +#eap_sim_id=3 + +# Trusted Network Connect (TNC) +# If enabled, TNC validation will be required before the peer is allowed to +# connect. Note: This is only used with EAP-TTLS and EAP-FAST. If any other +# EAP method is enabled, the peer will be allowed to connect without TNC. +#tnc=1 + +# EAP Re-authentication Protocol (ERP) - RFC 6696 +# +# Whether to enable ERP on the EAP server. +#eap_server_erp=1 + + +##### RADIUS client configuration ############################################# +# for IEEE 802.1X with external Authentication Server, IEEE 802.11 +# authentication with external ACL for MAC addresses, and accounting + +# The own IP address of the access point (used as NAS-IP-Address) +own_ip_addr=127.0.0.1 + +# NAS-Identifier string for RADIUS messages. When used, this should be unique +# to the NAS within the scope of the RADIUS server. Please note that hostapd +# uses a separate RADIUS client for each BSS and as such, a unique +# nas_identifier value should be configured separately for each BSS. This is +# particularly important for cases where RADIUS accounting is used +# (Accounting-On/Off messages are interpreted as clearing all ongoing sessions +# and that may get interpreted as applying to all BSSes if the same +# NAS-Identifier value is used.) For example, a fully qualified domain name +# prefixed with a unique identifier of the BSS (e.g., BSSID) can be used here. +# +# When using IEEE 802.11r, nas_identifier must be set and must be between 1 and +# 48 octets long. +# +# It is mandatory to configure either own_ip_addr or nas_identifier to be +# compliant with the RADIUS protocol. When using RADIUS accounting, it is +# strongly recommended that nas_identifier is set to a unique value for each +# BSS. +#nas_identifier=ap.example.com + +# RADIUS client forced local IP address for the access point +# Normally the local IP address is determined automatically based on configured +# IP addresses, but this field can be used to force a specific address to be +# used, e.g., when the device has multiple IP addresses. +#radius_client_addr=127.0.0.1 + +# RADIUS client forced local interface. Helps run properly with VRF +# Default is none set which allows the network stack to pick the appropriate +# interface automatically. +# Example below binds to eth0 +#radius_client_dev=eth0 + +# RADIUS authentication server +#auth_server_addr=127.0.0.1 +#auth_server_port=1812 +#auth_server_shared_secret=secret + +# RADIUS accounting server +#acct_server_addr=127.0.0.1 +#acct_server_port=1813 +#acct_server_shared_secret=secret + +# Secondary RADIUS servers; to be used if primary one does not reply to +# RADIUS packets. These are optional and there can be more than one secondary +# server listed. +#auth_server_addr=127.0.0.2 +#auth_server_port=1812 +#auth_server_shared_secret=secret2 +# +#acct_server_addr=127.0.0.2 +#acct_server_port=1813 +#acct_server_shared_secret=secret2 + +# Retry interval for trying to return to the primary RADIUS server (in +# seconds). RADIUS client code will automatically try to use the next server +# when the current server is not replying to requests. If this interval is set, +# primary server will be retried after configured amount of time even if the +# currently used secondary server is still working. +#radius_retry_primary_interval=600 + + +# Interim accounting update interval +# If this is set (larger than 0) and acct_server is configured, hostapd will +# send interim accounting updates every N seconds. Note: if set, this overrides +# possible Acct-Interim-Interval attribute in Access-Accept message. Thus, this +# value should not be configured in hostapd.conf, if RADIUS server is used to +# control the interim interval. +# This value should not be less 600 (10 minutes) and must not be less than +# 60 (1 minute). +#radius_acct_interim_interval=600 + +# Request Chargeable-User-Identity (RFC 4372) +# This parameter can be used to configure hostapd to request CUI from the +# RADIUS server by including Chargeable-User-Identity attribute into +# Access-Request packets. +#radius_request_cui=1 + +# Dynamic VLAN mode; allow RADIUS authentication server to decide which VLAN +# is used for the stations. This information is parsed from following RADIUS +# attributes based on RFC 3580 and RFC 2868: Tunnel-Type (value 13 = VLAN), +# Tunnel-Medium-Type (value 6 = IEEE 802), Tunnel-Private-Group-ID (value +# VLANID as a string). Optionally, the local MAC ACL list (accept_mac_file) can +# be used to set static client MAC address to VLAN ID mapping. +# Dynamic VLAN mode is also used with VLAN ID assignment based on WPA/WPA2 +# passphrase from wpa_psk_file or vlan_id parameter from sae_password. +# 0 = disabled (default); only VLAN IDs from accept_mac_file will be used +# 1 = optional; use default interface if RADIUS server does not include VLAN ID +# 2 = required; reject authentication if RADIUS server does not include VLAN ID +#dynamic_vlan=0 + +# Per-Station AP_VLAN interface mode +# If enabled, each station is assigned its own AP_VLAN interface. +# This implies per-station group keying and ebtables filtering of inter-STA +# traffic (when passed through the AP). +# If the sta is not assigned to any VLAN, then its AP_VLAN interface will be +# added to the bridge given by the "bridge" configuration option (see above). +# Otherwise, it will be added to the per-VLAN bridge. +# 0 = disabled (default) +# 1 = enabled +#per_sta_vif=0 + +# VLAN interface list for dynamic VLAN mode is read from a separate text file. +# This list is used to map VLAN ID from the RADIUS server to a network +# interface. Each station is bound to one interface in the same way as with +# multiple BSSIDs or SSIDs. Each line in this text file is defining a new +# interface and the line must include VLAN ID and interface name separated by +# white space (space or tab). +# If no entries are provided by this file, the station is statically mapped +# to <bss-iface>.<vlan-id> interfaces. +# Each line can optionally also contain the name of a bridge to add the VLAN to +#vlan_file=/etc/hostapd.vlan + +# Interface where 802.1q tagged packets should appear when a RADIUS server is +# used to determine which VLAN a station is on. hostapd creates a bridge for +# each VLAN. Then hostapd adds a VLAN interface (associated with the interface +# indicated by 'vlan_tagged_interface') and the appropriate wireless interface +# to the bridge. +#vlan_tagged_interface=eth0 + +# Bridge (prefix) to add the wifi and the tagged interface to. This gets the +# VLAN ID appended. It defaults to brvlan%d if no tagged interface is given +# and br%s.%d if a tagged interface is given, provided %s = tagged interface +# and %d = VLAN ID. +#vlan_bridge=brvlan + +# When hostapd creates a VLAN interface on vlan_tagged_interfaces, it needs +# to know how to name it. +# 0 = vlan<XXX>, e.g., vlan1 +# 1 = <vlan_tagged_interface>.<XXX>, e.g. eth0.1 +#vlan_naming=0 + +# Arbitrary RADIUS attributes can be added into Access-Request and +# Accounting-Request packets by specifying the contents of the attributes with +# the following configuration parameters. There can be multiple of these to +# add multiple attributes. These parameters can also be used to override some +# of the attributes added automatically by hostapd. +# Format: <attr_id>[:<syntax:value>] +# attr_id: RADIUS attribute type (e.g., 26 = Vendor-Specific) +# syntax: s = string (UTF-8), d = integer, x = octet string +# value: attribute value in format indicated by the syntax +# If syntax and value parts are omitted, a null value (single 0x00 octet) is +# used. +# +# Additional Access-Request attributes +# radius_auth_req_attr=<attr_id>[:<syntax:value>] +# Examples: +# Operator-Name = "Operator" +#radius_auth_req_attr=126:s:Operator +# Service-Type = Framed (2) +#radius_auth_req_attr=6:d:2 +# Connect-Info = "testing" (this overrides the automatically generated value) +#radius_auth_req_attr=77:s:testing +# Same Connect-Info value set as a hexdump +#radius_auth_req_attr=77:x:74657374696e67 + +# +# Additional Accounting-Request attributes +# radius_acct_req_attr=<attr_id>[:<syntax:value>] +# Examples: +# Operator-Name = "Operator" +#radius_acct_req_attr=126:s:Operator + +# If SQLite support is included, path to a database from which additional +# RADIUS request attributes are extracted based on the station MAC address. +# +# The schema for the radius_attributes table is: +# id | sta | reqtype | attr : multi-key (sta, reqtype) +# id = autonumber +# sta = station MAC address in `11:22:33:44:55:66` format. +# type = `auth` | `acct` | NULL (match any) +# attr = existing config file format, e.g. `126:s:Test Operator` +#radius_req_attr_sqlite=radius_attr.sqlite + +# Dynamic Authorization Extensions (RFC 5176) +# This mechanism can be used to allow dynamic changes to user session based on +# commands from a RADIUS server (or some other disconnect client that has the +# needed session information). For example, Disconnect message can be used to +# request an associated station to be disconnected. +# +# This is disabled by default. Set radius_das_port to non-zero UDP port +# number to enable. +#radius_das_port=3799 +# +# DAS client (the host that can send Disconnect/CoA requests) and shared secret +# Format: <IP address> <shared secret> +# IP address 0.0.0.0 can be used to allow requests from any address. +#radius_das_client=192.168.1.123 shared secret here +# +# DAS Event-Timestamp time window in seconds +#radius_das_time_window=300 +# +# DAS require Event-Timestamp +#radius_das_require_event_timestamp=1 +# +# DAS require Message-Authenticator +#radius_das_require_message_authenticator=1 + +##### RADIUS authentication server configuration ############################## + +# hostapd can be used as a RADIUS authentication server for other hosts. This +# requires that the integrated EAP server is also enabled and both +# authentication services are sharing the same configuration. + +# File name of the RADIUS clients configuration for the RADIUS server. If this +# commented out, RADIUS server is disabled. +#radius_server_clients=/etc/hostapd.radius_clients + +# The UDP port number for the RADIUS authentication server +#radius_server_auth_port=1812 + +# The UDP port number for the RADIUS accounting server +# Commenting this out or setting this to 0 can be used to disable RADIUS +# accounting while still enabling RADIUS authentication. +#radius_server_acct_port=1813 + +# Use IPv6 with RADIUS server (IPv4 will also be supported using IPv6 API) +#radius_server_ipv6=1 -{% elif security.wpa is vyos_defined %} ##### WPA/IEEE 802.11i configuration ########################################## # Enable WPA. Setting this variable configures the AP to require WPA (either @@ -531,17 +2054,68 @@ wep_key{{ loop.index -1 }}={{ security.wep.key }} # bit0 = WPA # bit1 = IEEE 802.11i/RSN (WPA2) (dot11RSNAEnabled) # Note that WPA3 is also configured with bit1 since it uses RSN just like WPA2. -# In other words, for WPA3, wpa 2 is used the configuration (and +# In other words, for WPA3, wpa=2 is used the configuration (and # wpa_key_mgmt=SAE for WPA3-Personal instead of wpa_key_mgmt=WPA-PSK). -{% if security.wpa.mode is vyos_defined('wpa+wpa2') %} -wpa=3 -{% elif security.wpa.mode is vyos_defined('wpa2') or security.wpa.mode is vyos_defined('wpa3') %} -wpa=2 -{% elif security.wpa.mode is vyos_defined('wpa') %} -wpa=1 -{% endif %} +#wpa=2 + +# Extended Key ID support for Individually Addressed frames +# +# Extended Key ID allows to rekey PTK keys without the impacts the "normal" +# PTK rekeying with only a single Key ID 0 has. It can only be used when the +# driver supports it and RSN/WPA2 is used with a CCMP/GCMP pairwise cipher. +# +# 0 = force off, i.e., use only Key ID 0 (default) +# 1 = enable and use Extended Key ID support when possible +# 2 = identical to 1 but start with Key ID 1 when possible +#extended_key_id=0 + +# WPA pre-shared keys for WPA-PSK. This can be either entered as a 256-bit +# secret in hex format (64 hex digits), wpa_psk, or as an ASCII passphrase +# (8..63 characters) that will be converted to PSK. This conversion uses SSID +# so the PSK changes when ASCII passphrase is used and the SSID is changed. +# wpa_psk (dot11RSNAConfigPSKValue) +# wpa_passphrase (dot11RSNAConfigPSKPassPhrase) +#wpa_psk=0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef +#wpa_passphrase=secret passphrase + +# Optionally, WPA PSKs can be read from a separate text file (containing list +# of (PSK,MAC address) pairs. This allows more than one PSK to be configured. +# Use absolute path name to make sure that the files can be read on SIGHUP +# configuration reloads. +#wpa_psk_file=/etc/hostapd.wpa_psk + +# Optionally, WPA passphrase can be received from RADIUS authentication server +# This requires macaddr_acl to be set to 2 (RADIUS) +# 0 = disabled (default) +# 1 = optional; use default passphrase/psk if RADIUS server does not include +# Tunnel-Password +# 2 = required; reject authentication if RADIUS server does not include +# Tunnel-Password +#wpa_psk_radius=0 + +# Set of accepted key management algorithms (WPA-PSK, WPA-EAP, or both). The +# entries are separated with a space. WPA-PSK-SHA256 and WPA-EAP-SHA256 can be +# added to enable SHA256-based stronger algorithms. +# WPA-PSK = WPA-Personal / WPA2-Personal +# WPA-PSK-SHA256 = WPA2-Personal using SHA256 +# WPA-EAP = WPA-Enterprise / WPA2-Enterprise +# WPA-EAP-SHA256 = WPA2-Enterprise using SHA256 +# SAE = SAE (WPA3-Personal) +# WPA-EAP-SUITE-B-192 = WPA3-Enterprise with 192-bit security/CNSA suite +# FT-PSK = FT with passphrase/PSK +# FT-EAP = FT with EAP +# FT-EAP-SHA384 = FT with EAP using SHA384 +# FT-SAE = FT with SAE +# FILS-SHA256 = Fast Initial Link Setup with SHA256 +# FILS-SHA384 = Fast Initial Link Setup with SHA384 +# FT-FILS-SHA256 = FT and Fast Initial Link Setup with SHA256 +# FT-FILS-SHA384 = FT and Fast Initial Link Setup with SHA384 +# OWE = Opportunistic Wireless Encryption (a.k.a. Enhanced Open) +# DPP = Device Provisioning Protocol +# OSEN = Hotspot 2.0 online signup with encryption +# (dot11RSNAConfigAuthenticationSuitesTable) +#wpa_key_mgmt=WPA-PSK WPA-EAP -{% if security.wpa.cipher is vyos_defined %} # Set of accepted cipher suites (encryption algorithms) for pairwise keys # (unicast packets). This is a space separated list of algorithms: # CCMP = AES in Counter mode with CBC-MAC (CCMP-128) @@ -554,194 +2128,1355 @@ wpa=1 # allowed as the pairwise cipher, group cipher will also be CCMP. Otherwise, # TKIP will be used as the group cipher. The optional group_cipher parameter can # be used to override this automatic selection. - -{% if security.wpa.mode is vyos_defined('wpa2') %} -# Pairwise cipher for RSN/WPA2 (default: use wpa_pairwise value) -rsn_pairwise={{ security.wpa.cipher | join(" ") }} -{% else %} +# +# (dot11RSNAConfigPairwiseCiphersTable) # Pairwise cipher for WPA (v1) (default: TKIP) -wpa_pairwise={{ security.wpa.cipher | join(" ") }} -{% endif %} -{% endif %} +#wpa_pairwise=TKIP CCMP +# Pairwise cipher for RSN/WPA2 (default: use wpa_pairwise value) +#rsn_pairwise=CCMP -{% if security.wpa.group_cipher is vyos_defined %} # Optional override for automatic group cipher selection # This can be used to select a specific group cipher regardless of which # pairwise ciphers were enabled for WPA and RSN. It should be noted that # overriding the group cipher with an unexpected value can result in # interoperability issues and in general, this parameter is mainly used for # testing purposes. -group_cipher={{ security.wpa.group_cipher | join(" ") }} -{% endif %} +#group_cipher=CCMP -{% if security.wpa.passphrase is vyos_defined %} -# IEEE 802.11 specifies two authentication algorithms. hostapd can be -# configured to allow both of these or only one. Open system authentication -# should be used with IEEE 802.1X. -# Bit fields of allowed authentication algorithms: -# bit 0 = Open System Authentication -# bit 1 = Shared Key Authentication (requires WEP) -auth_algs=1 +# Time interval for rekeying GTK (broadcast/multicast encryption keys) in +# seconds. (dot11RSNAConfigGroupRekeyTime) +# This defaults to 86400 seconds (once per day) when using CCMP/GCMP as the +# group cipher and 600 seconds (once per 10 minutes) when using TKIP as the +# group cipher. +#wpa_group_rekey=86400 -# WPA pre-shared keys for WPA-PSK. This can be either entered as a 256-bit -# secret in hex format (64 hex digits), wpa_psk, or as an ASCII passphrase -# (8..63 characters) that will be converted to PSK. This conversion uses SSID -# so the PSK changes when ASCII passphrase is used and the SSID is changed. -wpa_passphrase={{ security.wpa.passphrase }} +# Rekey GTK when any STA that possesses the current GTK is leaving the BSS. +# (dot11RSNAConfigGroupRekeyStrict) +#wpa_strict_rekey=1 -# Set of accepted key management algorithms (WPA-PSK, WPA-EAP, or both). The -# entries are separated with a space. WPA-PSK-SHA256 and WPA-EAP-SHA256 can be -# added to enable SHA256-based stronger algorithms. -# WPA-PSK = WPA-Personal / WPA2-Personal -# WPA-PSK-SHA256 = WPA2-Personal using SHA256 -# WPA-EAP = WPA-Enterprise / WPA2-Enterprise -# WPA-EAP-SHA256 = WPA2-Enterprise using SHA256 -# SAE = SAE (WPA3-Personal) -# WPA-EAP-SUITE-B-192 = WPA3-Enterprise with 192-bit security/CNSA suite -{% if security.wpa.mode is vyos_defined('wpa3') %} -wpa_key_mgmt=SAE -{% else %} -wpa_key_mgmt=WPA-PSK WPA-PSK-SHA256 -{% endif %} +# The number of times EAPOL-Key Message 1/2 in the RSN Group Key Handshake is +#retried per GTK Handshake attempt. (dot11RSNAConfigGroupUpdateCount) +# This value should only be increased when stations are constantly +# deauthenticated during GTK rekeying with the log message +# "group key handshake failed...". +# You should consider to also increase wpa_pairwise_update_count then. +# Range 1..4294967295; default: 4 +#wpa_group_update_count=4 -{% elif security.wpa.radius is vyos_defined %} -##### IEEE 802.1X-2004 related configuration ################################## -# Require IEEE 802.1X authorization -ieee8021x=1 +# Time interval for rekeying GMK (master key used internally to generate GTKs +# (in seconds). +#wpa_gmk_rekey=86400 -# Set of accepted key management algorithms (WPA-PSK, WPA-EAP, or both). The -# entries are separated with a space. WPA-PSK-SHA256 and WPA-EAP-SHA256 can be -# added to enable SHA256-based stronger algorithms. -# WPA-PSK = WPA-Personal / WPA2-Personal -# WPA-PSK-SHA256 = WPA2-Personal using SHA256 -# WPA-EAP = WPA-Enterprise / WPA2-Enterprise -# WPA-EAP-SHA256 = WPA2-Enterprise using SHA256 -# SAE = SAE (WPA3-Personal) -# WPA-EAP-SUITE-B-192 = WPA3-Enterprise with 192-bit security/CNSA suite -{% if security.wpa.mode is vyos_defined('wpa3') %} -wpa_key_mgmt=WPA-EAP-SUITE-B-192 -{% else %} -wpa_key_mgmt=WPA-EAP WPA-EAP-SHA256 -{% endif %} +# Maximum lifetime for PTK in seconds. This can be used to enforce rekeying of +# PTK to mitigate some attacks against TKIP deficiencies. +# Warning: PTK rekeying is buggy with many drivers/devices and with such +# devices, the only secure method to rekey the PTK without Extended Key ID +# support requires a disconnection. Check the related parameter +# wpa_deny_ptk0_rekey for details. +#wpa_ptk_rekey=600 -{% if security.wpa.radius.server is vyos_defined %} -# RADIUS client forced local IP address for the access point -# Normally the local IP address is determined automatically based on configured -# IP addresses, but this field can be used to force a specific address to be -# used, e.g., when the device has multiple IP addresses. -# The own IP address of the access point (used as NAS-IP-Address) -{% if security.wpa.radius.source_address is vyos_defined %} -radius_client_addr={{ security.wpa.radius.source_address }} -own_ip_addr={{ security.wpa.radius.source_address }} -{% else %} -own_ip_addr=127.0.0.1 -{% endif %} +# Workaround for PTK rekey issues +# +# PTK0 rekeys (rekeying the PTK without "Extended Key ID for Individually +# Addressed Frames") can degrade the security and stability with some cards. +# To avoid such issues hostapd can replace those PTK rekeys (including EAP +# reauthentications) with disconnects. +# +# Available options: +# 0 = always rekey when configured/instructed (default) +# 1 = only rekey when the local driver is explicitly indicating it can perform +# this operation without issues +# 2 = never allow PTK0 rekeys +#wpa_deny_ptk0_rekey=0 -{% for radius in security.wpa.radius.server if not radius.disabled %} -# RADIUS authentication server -auth_server_addr={{ radius.server }} -auth_server_port={{ radius.port }} -auth_server_shared_secret={{ radius.key }} +# The number of times EAPOL-Key Message 1/4 and Message 3/4 in the RSN 4-Way +# Handshake are retried per 4-Way Handshake attempt. +# (dot11RSNAConfigPairwiseUpdateCount) +# Range 1..4294967295; default: 4 +#wpa_pairwise_update_count=4 -{% if radius.acc_port %} -# RADIUS accounting server -acct_server_addr={{ radius.server }} -acct_server_port={{ radius.acc_port }} -acct_server_shared_secret={{ radius.key }} -{% endif %} -{% endfor %} -{% else %} -# Open system -auth_algs=1 -{% endif %} -{% endif %} -{% endif %} +# Workaround for key reinstallation attacks +# +# This parameter can be used to disable retransmission of EAPOL-Key frames that +# are used to install keys (EAPOL-Key message 3/4 and group message 1/2). This +# is similar to setting wpa_group_update_count=1 and +# wpa_pairwise_update_count=1, but with no impact to message 1/4 and with +# extended timeout on the response to avoid causing issues with stations that +# may use aggressive power saving have very long time in replying to the +# EAPOL-Key messages. +# +# This option can be used to work around key reinstallation attacks on the +# station (supplicant) side in cases those station devices cannot be updated +# for some reason. By removing the retransmissions the attacker cannot cause +# key reinstallation with a delayed frame transmission. This is related to the +# station side vulnerabilities CVE-2017-13077, CVE-2017-13078, CVE-2017-13079, +# CVE-2017-13080, and CVE-2017-13081. +# +# This workaround might cause interoperability issues and reduced robustness of +# key negotiation especially in environments with heavy traffic load due to the +# number of attempts to perform the key exchange is reduced significantly. As +# such, this workaround is disabled by default (unless overridden in build +# configuration). To enable this, set the parameter to 1. +#wpa_disable_eapol_key_retries=1 -# TX queue parameters (EDCF / bursting) -# tx_queue_<queue name>_<param> -# queues: data0, data1, data2, data3 -# (data0 is the highest priority queue) -# parameters: -# aifs: AIFS (default 2) -# cwmin: cwMin (1, 3, 7, 15, 31, 63, 127, 255, 511, 1023, 2047, 4095, 8191, -# 16383, 32767) -# cwmax: cwMax (same values as cwMin, cwMax >= cwMin) -# burst: maximum length (in milliseconds with precision of up to 0.1 ms) for -# bursting +# Enable IEEE 802.11i/RSN/WPA2 pre-authentication. This is used to speed up +# roaming be pre-authenticating IEEE 802.1X/EAP part of the full RSN +# authentication and key handshake before actually associating with a new AP. +# (dot11RSNAPreauthenticationEnabled) +#rsn_preauth=1 # -# Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e): -# These parameters are used by the access point when transmitting frames -# to the clients. +# Space separated list of interfaces from which pre-authentication frames are +# accepted (e.g., 'eth0' or 'eth0 wlan0wds0'. This list should include all +# interface that are used for connections to other APs. This could include +# wired interfaces and WDS links. The normal wireless data interface towards +# associated stations (e.g., wlan0) should not be added, since +# pre-authentication is only used with APs other than the currently associated +# one. +#rsn_preauth_interfaces=eth0 + +# ieee80211w: Whether management frame protection (MFP) is enabled +# 0 = disabled (default) +# 1 = optional +# 2 = required +#ieee80211w=0 +# The most common configuration options for this based on the PMF (protected +# management frames) certification program are: +# PMF enabled: ieee80211w=1 and wpa_key_mgmt=WPA-EAP WPA-EAP-SHA256 +# PMF required: ieee80211w=2 and wpa_key_mgmt=WPA-EAP-SHA256 +# (and similarly for WPA-PSK and WPA-PSK-SHA256 if WPA2-Personal is used) +# WPA3-Personal-only mode: ieee80211w=2 and wpa_key_mgmt=SAE + +# Group management cipher suite +# Default: AES-128-CMAC (BIP) +# Other options (depending on driver support): +# BIP-GMAC-128 +# BIP-GMAC-256 +# BIP-CMAC-256 +# Note: All the stations connecting to the BSS will also need to support the +# selected cipher. The default AES-128-CMAC is the only option that is commonly +# available in deployed devices. +#group_mgmt_cipher=AES-128-CMAC + +# Beacon Protection (management frame protection for Beacon frames) +# This depends on management frame protection being enabled (ieee80211w != 0) +# and beacon protection support indication from the driver. +# 0 = disabled (default) +# 1 = enabled +#beacon_prot=0 + +# Association SA Query maximum timeout (in TU = 1.024 ms; for MFP) +# (maximum time to wait for a SA Query response) +# dot11AssociationSAQueryMaximumTimeout, 1...4294967295 +#assoc_sa_query_max_timeout=1000 + +# Association SA Query retry timeout (in TU = 1.024 ms; for MFP) +# (time between two subsequent SA Query requests) +# dot11AssociationSAQueryRetryTimeout, 1...4294967295 +#assoc_sa_query_retry_timeout=201 + +# ocv: Operating Channel Validation +# This is a countermeasure against multi-channel on-path attacks. +# Enabling this depends on the driver's support for OCV when the driver SME is +# used. If hostapd SME is used, this will be enabled just based on this +# configuration. +# Enabling this automatically also enables ieee80211w, if not yet enabled. +# 0 = disabled (default) +# 1 = enabled +# 2 = enabled in workaround mode - Allow STA that claims OCV capability to +# connect even if the STA doesn't send OCI or negotiate PMF. This +# workaround is to improve interoperability with legacy STAs which are +# wrongly copying reserved bits of RSN capabilities from the AP's +# RSNE into (Re)Association Request frames. When this configuration is +# enabled, the AP considers STA is OCV capable only when the STA indicates +# MFP capability in (Re)Association Request frames and sends OCI in +# EAPOL-Key msg 2/4/FT Reassociation Request frame/FILS (Re)Association +# Request frame; otherwise, the AP disables OCV for the current connection +# with the STA. Enabling this workaround mode reduced OCV protection to +# some extend since it allows misbehavior to go through. As such, this +# should be enabled only if interoperability with misbehaving STAs is +# needed. +#ocv=1 + +# disable_pmksa_caching: Disable PMKSA caching +# This parameter can be used to disable caching of PMKSA created through EAP +# authentication. RSN preauthentication may still end up using PMKSA caching if +# it is enabled (rsn_preauth=1). +# 0 = PMKSA caching enabled (default) +# 1 = PMKSA caching disabled +#disable_pmksa_caching=0 + +# okc: Opportunistic Key Caching (aka Proactive Key Caching) +# Allow PMK cache to be shared opportunistically among configured interfaces +# and BSSes (i.e., all configurations within a single hostapd process). +# 0 = disabled (default) +# 1 = enabled +#okc=1 + +# SAE password +# This parameter can be used to set passwords for SAE. By default, the +# wpa_passphrase value is used if this separate parameter is not used, but +# wpa_passphrase follows the WPA-PSK constraints (8..63 characters) even though +# SAE passwords do not have such constraints. If the BSS enabled both SAE and +# WPA-PSK and both values are set, SAE uses the sae_password values and WPA-PSK +# uses the wpa_passphrase value. # -# Low priority / AC_BK = background -tx_queue_data3_aifs=7 -tx_queue_data3_cwmin=15 -tx_queue_data3_cwmax=1023 -tx_queue_data3_burst=0 -# Note: for IEEE 802.11b mode: cWmin=31 cWmax=1023 burst=0 +# Each sae_password entry is added to a list of available passwords. This +# corresponds to the dot11RSNAConfigPasswordValueEntry. sae_password value +# starts with the password (dot11RSNAConfigPasswordCredential). That value can +# be followed by optional peer MAC address (dot11RSNAConfigPasswordPeerMac) and +# by optional password identifier (dot11RSNAConfigPasswordIdentifier). In +# addition, an optional VLAN ID specification can be used to bind the station +# to the specified VLAN whenever the specific SAE password entry is used. # -# Normal priority / AC_BE = best effort -tx_queue_data2_aifs=3 -tx_queue_data2_cwmin=15 -tx_queue_data2_cwmax=63 -tx_queue_data2_burst=0 -# Note: for IEEE 802.11b mode: cWmin=31 cWmax=127 burst=0 +# If the peer MAC address is not included or is set to the wildcard address +# (ff:ff:ff:ff:ff:ff), the entry is available for any station to use. If a +# specific peer MAC address is included, only a station with that MAC address +# is allowed to use the entry. # -# High priority / AC_VI = video -tx_queue_data1_aifs=1 -tx_queue_data1_cwmin=7 -tx_queue_data1_cwmax=15 -tx_queue_data1_burst=3.0 -# Note: for IEEE 802.11b mode: cWmin=15 cWmax=31 burst=6.0 +# If the password identifier (with non-zero length) is included, the entry is +# limited to be used only with that specified identifier. + +# The last matching (based on peer MAC address and identifier) entry is used to +# select which password to use. Setting sae_password to an empty string has a +# special meaning of removing all previously added entries. # -# Highest priority / AC_VO = voice -tx_queue_data0_aifs=1 -tx_queue_data0_cwmin=3 -tx_queue_data0_cwmax=7 -tx_queue_data0_burst=1.5 +# sae_password uses the following encoding: +#<password/credential>[|mac=<peer mac>][|vlanid=<VLAN ID>] +#[|pk=<m:ECPrivateKey-base64>][|id=<identifier>] +# Examples: +#sae_password=secret +#sae_password=really secret|mac=ff:ff:ff:ff:ff:ff +#sae_password=example secret|mac=02:03:04:05:06:07|id=pw identifier +#sae_password=example secret|vlanid=3|id=pw identifier -# Default WMM parameters (IEEE 802.11 draft; 11-03-0504-03-000e): -# for 802.11a or 802.11g networks -# These parameters are sent to WMM clients when they associate. -# The parameters will be used by WMM clients for frames transmitted to the -# access point. +# SAE threshold for anti-clogging mechanism (dot11RSNASAEAntiCloggingThreshold) +# This parameter defines how many open SAE instances can be in progress at the +# same time before the anti-clogging mechanism is taken into use. +#sae_anti_clogging_threshold=5 (deprecated) +#anti_clogging_threshold=5 + +# Maximum number of SAE synchronization errors (dot11RSNASAESync) +# The offending SAE peer will be disconnected if more than this many +# synchronization errors happen. +#sae_sync=5 + +# Enabled SAE finite cyclic groups +# SAE implementation are required to support group 19 (ECC group defined over a +# 256-bit prime order field). This configuration parameter can be used to +# specify a set of allowed groups. If not included, only the mandatory group 19 +# is enabled. +# The group values are listed in the IANA registry: +# http://www.iana.org/assignments/ipsec-registry/ipsec-registry.xml#ipsec-registry-9 +# Note that groups 1, 2, 5, 22, 23, and 24 should not be used in production +# purposes due limited security (see RFC 8247). Groups that are not as strong as +# group 19 (ECC, NIST P-256) are unlikely to be useful for production use cases +# since all implementations are required to support group 19. +#sae_groups=19 20 21 + +# Require MFP for all associations using SAE +# This parameter can be used to enforce negotiation of MFP for all associations +# that negotiate use of SAE. This is used in cases where SAE-capable devices are +# known to be MFP-capable and the BSS is configured with optional MFP +# (ieee80211w=1) for legacy support. The non-SAE stations can connect without +# MFP while SAE stations are required to negotiate MFP if sae_require_mfp=1. +#sae_require_mfp=0 + +# SAE Confirm behavior +# By default, AP will send out only SAE Commit message in response to a received +# SAE Commit message. This parameter can be set to 1 to override that behavior +# to send both SAE Commit and SAE Confirm messages without waiting for the STA +# to send its SAE Confirm message first. +#sae_confirm_immediate=0 + +# SAE mechanism for PWE derivation +# 0 = hunting-and-pecking loop only (default without password identifier) +# 1 = hash-to-element only (default with password identifier) +# 2 = both hunting-and-pecking loop and hash-to-element enabled +# Note: The default value is likely to change from 0 to 2 once the new +# hash-to-element mechanism has received more interoperability testing. +# When using SAE password identifier, the hash-to-element mechanism is used +# regardless of the sae_pwe parameter value. +#sae_pwe=0 + +# FILS Cache Identifier (16-bit value in hexdump format) +#fils_cache_id=0011 + +# FILS Realm Information +# One or more FILS realms need to be configured when FILS is enabled. This list +# of realms is used to define which realms (used in keyName-NAI by the client) +# can be used with FILS shared key authentication for ERP. +#fils_realm=example.com +#fils_realm=example.org + +# FILS DH Group for PFS +# 0 = PFS disabled with FILS shared key authentication (default) +# 1-65535 DH Group to use for FILS PFS +#fils_dh_group=0 + +# OWE DH groups +# OWE implementations are required to support group 19 (NIST P-256). All groups +# that are supported by the implementation (e.g., groups 19, 20, and 21 when +# using OpenSSL) are enabled by default. This configuration parameter can be +# used to specify a limited set of allowed groups. The group values are listed +# in the IANA registry: +# http://www.iana.org/assignments/ipsec-registry/ipsec-registry.xml#ipsec-registry-10 +#owe_groups=19 20 21 + +# OWE PTK derivation workaround +# Initial OWE implementation used SHA256 when deriving the PTK for all OWE +# groups. This was supposed to change to SHA384 for group 20 and SHA512 for +# group 21. This parameter can be used to enable workaround for interoperability +# with stations that use SHA256 with groups 20 and 21. By default (0) only the +# appropriate hash function is accepted. When workaround is enabled (1), the +# appropriate hash function is tried first and if that fails, SHA256-based PTK +# derivation is attempted. This workaround can result in reduced security for +# groups 20 and 21, but is required for interoperability with older +# implementations. There is no impact to group 19 behavior. The workaround is +# disabled by default and can be enabled by uncommenting the following line. +#owe_ptk_workaround=1 + +# OWE transition mode configuration +# Pointer to the matching open/OWE BSS +#owe_transition_bssid=<bssid> +# SSID in same format as ssid2 described above. +#owe_transition_ssid=<SSID> +# Alternatively, OWE transition mode BSSID/SSID can be configured with a +# reference to a BSS operated by this hostapd process. +#owe_transition_ifname=<ifname> + +# DHCP server for FILS HLP +# If configured, hostapd will act as a DHCP relay for all FILS HLP requests +# that include a DHCPDISCOVER message and send them to the specific DHCP +# server for processing. hostapd will then wait for a response from that server +# before replying with (Re)Association Response frame that encapsulates this +# DHCP response. own_ip_addr is used as the local address for the communication +# with the DHCP server. +#dhcp_server=127.0.0.1 + +# DHCP server UDP port +# Default: 67 +#dhcp_server_port=67 + +# DHCP relay UDP port on the local device +# Default: 67; 0 means not to bind any specific port +#dhcp_relay_port=67 + +# DHCP rapid commit proxy +# If set to 1, this enables hostapd to act as a DHCP rapid commit proxy to +# allow the rapid commit options (two message DHCP exchange) to be used with a +# server that supports only the four message DHCP exchange. This is disabled by +# default (= 0) and can be enabled by setting this to 1. +#dhcp_rapid_commit_proxy=0 + +# Wait time for FILS HLP (dot11HLPWaitTime) in TUs +# default: 30 TUs (= 30.72 milliseconds) +#fils_hlp_wait_time=30 + +# FILS Discovery frame transmission minimum and maximum interval settings. +# If fils_discovery_max_interval is non-zero, the AP enables FILS Discovery +# frame transmission. These values use TUs as the unit and have allowed range +# of 0-10000. fils_discovery_min_interval defaults to 20. +#fils_discovery_min_interval=20 +#fils_discovery_max_interval=0 + +# Transition Disable indication +# The AP can notify authenticated stations to disable transition mode in their +# network profiles when the network has completed transition steps, i.e., once +# sufficiently large number of APs in the ESS have been updated to support the +# more secure alternative. When this indication is used, the stations are +# expected to automatically disable transition mode and less secure security +# options. This includes use of WEP, TKIP (including use of TKIP as the group +# cipher), and connections without PMF. +# Bitmap bits: +# bit 0 (0x01): WPA3-Personal (i.e., disable WPA2-Personal = WPA-PSK and only +# allow SAE to be used) +# bit 1 (0x02): SAE-PK (disable SAE without use of SAE-PK) +# bit 2 (0x04): WPA3-Enterprise (move to requiring PMF) +# bit 3 (0x08): Enhanced Open (disable use of open network; require OWE) +# (default: 0 = do not include Transition Disable KDE) +#transition_disable=0x01 + +# PASN ECDH groups +# PASN implementations are required to support group 19 (NIST P-256). If this +# parameter is not set, only group 19 is supported by default. This +# configuration parameter can be used to specify a limited set of allowed +# groups. The group values are listed in the IANA registry: +# http://www.iana.org/assignments/ipsec-registry/ipsec-registry.xml#ipsec-registry-10 +#pasn_groups=19 20 21 + +# PASN comeback after time in TUs +# In case the AP is temporarily unable to handle a PASN authentication exchange +# due to a too large number of parallel operations, this value indicates to the +# peer after how many TUs it can try the PASN exchange again. +# (default: 10 TUs) +#pasn_comeback_after=10 + +##### IEEE 802.11r configuration ############################################## + +# Mobility Domain identifier (dot11FTMobilityDomainID, MDID) +# MDID is used to indicate a group of APs (within an ESS, i.e., sharing the +# same SSID) between which a STA can use Fast BSS Transition. +# 2-octet identifier as a hex string. +#mobility_domain=a1b2 + +# PMK-R0 Key Holder identifier (dot11FTR0KeyHolderID) +# 1 to 48 octet identifier. +# This is configured with nas_identifier (see RADIUS client section above). + +# Default lifetime of the PMK-R0 in seconds; range 60..4294967295 +# (default: 14 days / 1209600 seconds; 0 = disable timeout) +# (dot11FTR0KeyLifetime) +#ft_r0_key_lifetime=1209600 + +# Maximum lifetime for PMK-R1; applied only if not zero +# PMK-R1 is removed at latest after this limit. +# Removing any PMK-R1 for expiry can be disabled by setting this to -1. +# (default: 0) +#r1_max_key_lifetime=0 + +# PMK-R1 Key Holder identifier (dot11FTR1KeyHolderID) +# 6-octet identifier as a hex string. +# Defaults to BSSID. +#r1_key_holder=000102030405 + +# Reassociation deadline in time units (TUs / 1.024 ms; range 1000..65535) +# (dot11FTReassociationDeadline) +#reassociation_deadline=1000 + +# List of R0KHs in the same Mobility Domain +# format: <MAC address> <NAS Identifier> <256-bit key as hex string> +# This list is used to map R0KH-ID (NAS Identifier) to a destination MAC +# address when requesting PMK-R1 key from the R0KH that the STA used during the +# Initial Mobility Domain Association. +#r0kh=02:01:02:03:04:05 r0kh-1.example.com 000102030405060708090a0b0c0d0e0f000102030405060708090a0b0c0d0e0f +#r0kh=02:01:02:03:04:06 r0kh-2.example.com 00112233445566778899aabbccddeeff00112233445566778899aabbccddeeff +# And so on.. One line per R0KH. +# Wildcard entry: +# Upon receiving a response from R0KH, it will be added to this list, so +# subsequent requests won't be broadcast. If R0KH does not reply, it will be +# temporarily blocked (see rkh_neg_timeout). +#r0kh=ff:ff:ff:ff:ff:ff * 00112233445566778899aabbccddeeff + +# List of R1KHs in the same Mobility Domain +# format: <MAC address> <R1KH-ID> <256-bit key as hex string> +# This list is used to map R1KH-ID to a destination MAC address when sending +# PMK-R1 key from the R0KH. This is also the list of authorized R1KHs in the MD +# that can request PMK-R1 keys. +#r1kh=02:01:02:03:04:05 02:11:22:33:44:55 000102030405060708090a0b0c0d0e0f000102030405060708090a0b0c0d0e0f +#r1kh=02:01:02:03:04:06 02:11:22:33:44:66 00112233445566778899aabbccddeeff00112233445566778899aabbccddeeff +# And so on.. One line per R1KH. +# Wildcard entry: +# Upon receiving a request from an R1KH not yet known, it will be added to this +# list and thus will receive push notifications. +#r1kh=00:00:00:00:00:00 00:00:00:00:00:00 00112233445566778899aabbccddeeff + +# Timeout (seconds) for newly discovered R0KH/R1KH (see wildcard entries above) +# Special values: 0 -> do not expire +# Warning: do not cache implies no sequence number validation with wildcards +#rkh_pos_timeout=86400 (default = 1 day) + +# Timeout (milliseconds) for requesting PMK-R1 from R0KH using PULL request +# and number of retries. +#rkh_pull_timeout=1000 (default = 1 second) +#rkh_pull_retries=4 (default) + +# Timeout (seconds) for non replying R0KH (see wildcard entries above) +# Special values: 0 -> do not cache +# default: 60 seconds +#rkh_neg_timeout=60 + +# Note: The R0KH/R1KH keys used to be 128-bit in length before the message +# format was changed. That shorter key length is still supported for backwards +# compatibility of the configuration files. If such a shorter key is used, a +# 256-bit key is derived from it. For new deployments, configuring the 256-bit +# key is recommended. + +# Whether PMK-R1 push is enabled at R0KH +# 0 = do not push PMK-R1 to all configured R1KHs (default) +# 1 = push PMK-R1 to all configured R1KHs whenever a new PMK-R0 is derived +#pmk_r1_push=1 + +# Whether to enable FT-over-DS +# 0 = FT-over-DS disabled +# 1 = FT-over-DS enabled (default) +#ft_over_ds=1 + +# Whether to generate FT response locally for PSK networks +# This avoids use of PMK-R1 push/pull from other APs with FT-PSK networks as +# the required information (PSK and other session data) is already locally +# available. +# 0 = disabled (default) +# 1 = enabled +#ft_psk_generate_local=0 + +##### Neighbor table ########################################################## +# Maximum number of entries kept in AP table (either for neighbor table or for +# detecting Overlapping Legacy BSS Condition). The oldest entry will be +# removed when adding a new entry that would make the list grow over this +# limit. Note! WFA certification for IEEE 802.11g requires that OLBC is +# enabled, so this field should not be set to 0 when using IEEE 802.11g. +# default: 255 +#ap_table_max_size=255 + +# Number of seconds of no frames received after which entries may be deleted +# from the AP table. Since passive scanning is not usually performed frequently +# this should not be set to very small value. In addition, there is no +# guarantee that every scan cycle will receive beacon frames from the +# neighboring APs. +# default: 60 +#ap_table_expiration_time=3600 + +# Maximum number of stations to track on the operating channel +# This can be used to detect dualband capable stations before they have +# associated, e.g., to provide guidance on which colocated BSS to use. +# Default: 0 (disabled) +#track_sta_max_num=100 + +# Maximum age of a station tracking entry in seconds +# Default: 180 +#track_sta_max_age=180 + +# Do not reply to group-addressed Probe Request from a station that was seen on +# another radio. +# Default: Disabled # -# note - txop_limit is in units of 32microseconds -# note - acm is admission control mandatory flag. 0 = admission control not -# required, 1 = mandatory -# note - Here cwMin and cmMax are in exponent form. The actual cw value used -# will be (2^n)-1 where n is the value given here. The allowed range for these -# wmm_ac_??_{cwmin,cwmax} is 0..15 with cwmax >= cwmin. +# This can be used with enabled track_sta_max_num configuration on another +# interface controlled by the same hostapd process to restrict Probe Request +# frame handling from replying to group-addressed Probe Request frames from a +# station that has been detected to be capable of operating on another band, +# e.g., to try to reduce likelihood of the station selecting a 2.4 GHz BSS when +# the AP operates both a 2.4 GHz and 5 GHz BSS concurrently. # -wmm_enabled=1 +# Note: Enabling this can cause connectivity issues and increase latency for +# discovering the AP. +#no_probe_resp_if_seen_on=wlan1 -# Low priority / AC_BK = background -wmm_ac_bk_cwmin=4 -wmm_ac_bk_cwmax=10 -wmm_ac_bk_aifs=7 -wmm_ac_bk_txop_limit=0 -wmm_ac_bk_acm=0 -# Note: for IEEE 802.11b mode: cWmin=5 cWmax=10 +# Reject authentication from a station that was seen on another radio. +# Default: Disabled # -# Normal priority / AC_BE = best effort -wmm_ac_be_aifs=3 -wmm_ac_be_cwmin=4 -wmm_ac_be_cwmax=10 -wmm_ac_be_txop_limit=0 -wmm_ac_be_acm=0 -# Note: for IEEE 802.11b mode: cWmin=5 cWmax=7 +# This can be used with enabled track_sta_max_num configuration on another +# interface controlled by the same hostapd process to reject authentication +# attempts from a station that has been detected to be capable of operating on +# another band, e.g., to try to reduce likelihood of the station selecting a +# 2.4 GHz BSS when the AP operates both a 2.4 GHz and 5 GHz BSS concurrently. # -# High priority / AC_VI = video -wmm_ac_vi_aifs=2 -wmm_ac_vi_cwmin=3 -wmm_ac_vi_cwmax=4 -wmm_ac_vi_txop_limit=94 -wmm_ac_vi_acm=0 -# Note: for IEEE 802.11b mode: cWmin=4 cWmax=5 txop_limit=188 +# Note: Enabling this can cause connectivity issues and increase latency for +# connecting with the AP. +#no_auth_if_seen_on=wlan1 + +##### Wi-Fi Protected Setup (WPS) ############################################# + +# WPS state +# 0 = WPS disabled (default) +# 1 = WPS enabled, not configured +# 2 = WPS enabled, configured +#wps_state=2 + +# Whether to manage this interface independently from other WPS interfaces +# By default, a single hostapd process applies WPS operations to all configured +# interfaces. This parameter can be used to disable that behavior for a subset +# of interfaces. If this is set to non-zero for an interface, WPS commands +# issued on that interface do not apply to other interfaces and WPS operations +# performed on other interfaces do not affect this interface. +#wps_independent=0 + +# AP can be configured into a locked state where new WPS Registrar are not +# accepted, but previously authorized Registrars (including the internal one) +# can continue to add new Enrollees. +#ap_setup_locked=1 + +# Universally Unique IDentifier (UUID; see RFC 4122) of the device +# This value is used as the UUID for the internal WPS Registrar. If the AP +# is also using UPnP, this value should be set to the device's UPnP UUID. +# If not configured, UUID will be generated based on the local MAC address. +#uuid=12345678-9abc-def0-1234-56789abcdef0 + +# Note: If wpa_psk_file is set, WPS is used to generate random, per-device PSKs +# that will be appended to the wpa_psk_file. If wpa_psk_file is not set, the +# default PSK (wpa_psk/wpa_passphrase) will be delivered to Enrollees. Use of +# per-device PSKs is recommended as the more secure option (i.e., make sure to +# set wpa_psk_file when using WPS with WPA-PSK). + +# When an Enrollee requests access to the network with PIN method, the Enrollee +# PIN will need to be entered for the Registrar. PIN request notifications are +# sent to hostapd ctrl_iface monitor. In addition, they can be written to a +# text file that could be used, e.g., to populate the AP administration UI with +# pending PIN requests. If the following variable is set, the PIN requests will +# be written to the configured file. +#wps_pin_requests=/var/run/hostapd_wps_pin_requests + +# Device Name +# User-friendly description of device; up to 32 octets encoded in UTF-8 +#device_name=Wireless AP + +# Manufacturer +# The manufacturer of the device (up to 64 ASCII characters) +#manufacturer=Company + +# Model Name +# Model of the device (up to 32 ASCII characters) +#model_name=WAP + +# Model Number +# Additional device description (up to 32 ASCII characters) +#model_number=123 + +# Serial Number +# Serial number of the device (up to 32 characters) +#serial_number=12345 + +# Primary Device Type +# Used format: <categ>-<OUI>-<subcateg> +# categ = Category as an integer value +# OUI = OUI and type octet as a 4-octet hex-encoded value; 0050F204 for +# default WPS OUI +# subcateg = OUI-specific Sub Category as an integer value +# Examples: +# 1-0050F204-1 (Computer / PC) +# 1-0050F204-2 (Computer / Server) +# 5-0050F204-1 (Storage / NAS) +# 6-0050F204-1 (Network Infrastructure / AP) +#device_type=6-0050F204-1 + +# OS Version +# 4-octet operating system version number (hex string) +#os_version=01020300 + +# Config Methods +# List of the supported configuration methods +# Available methods: usba ethernet label display ext_nfc_token int_nfc_token +# nfc_interface push_button keypad virtual_display physical_display +# virtual_push_button physical_push_button +#config_methods=label virtual_display virtual_push_button keypad + +# WPS capability discovery workaround for PBC with Windows 7 +# Windows 7 uses incorrect way of figuring out AP's WPS capabilities by acting +# as a Registrar and using M1 from the AP. The config methods attribute in that +# message is supposed to indicate only the configuration method supported by +# the AP in Enrollee role, i.e., to add an external Registrar. For that case, +# PBC shall not be used and as such, the PushButton config method is removed +# from M1 by default. If pbc_in_m1=1 is included in the configuration file, +# the PushButton config method is left in M1 (if included in config_methods +# parameter) to allow Windows 7 to use PBC instead of PIN (e.g., from a label +# in the AP). +#pbc_in_m1=1 + +# Static access point PIN for initial configuration and adding Registrars +# If not set, hostapd will not allow external WPS Registrars to control the +# access point. The AP PIN can also be set at runtime with hostapd_cli +# wps_ap_pin command. Use of temporary (enabled by user action) and random +# AP PIN is much more secure than configuring a static AP PIN here. As such, +# use of the ap_pin parameter is not recommended if the AP device has means for +# displaying a random PIN. +#ap_pin=12345670 + +# Skip building of automatic WPS credential +# This can be used to allow the automatically generated Credential attribute to +# be replaced with pre-configured Credential(s). +#skip_cred_build=1 + +# Additional Credential attribute(s) +# This option can be used to add pre-configured Credential attributes into M8 +# message when acting as a Registrar. If skip_cred_build=1, this data will also +# be able to override the Credential attribute that would have otherwise been +# automatically generated based on network configuration. This configuration +# option points to an external file that much contain the WPS Credential +# attribute(s) as binary data. +#extra_cred=hostapd.cred + +# Credential processing +# 0 = process received credentials internally (default) +# 1 = do not process received credentials; just pass them over ctrl_iface to +# external program(s) +# 2 = process received credentials internally and pass them over ctrl_iface +# to external program(s) +# Note: With wps_cred_processing=1, skip_cred_build should be set to 1 and +# extra_cred be used to provide the Credential data for Enrollees. # -# Highest priority / AC_VO = voice -wmm_ac_vo_aifs=2 -wmm_ac_vo_cwmin=2 -wmm_ac_vo_cwmax=3 -wmm_ac_vo_txop_limit=47 -wmm_ac_vo_acm=0 +# wps_cred_processing=1 will disabled automatic updates of hostapd.conf file +# both for Credential processing and for marking AP Setup Locked based on +# validation failures of AP PIN. An external program is responsible on updating +# the configuration appropriately in this case. +#wps_cred_processing=0 + +# Whether to enable SAE (WPA3-Personal transition mode) automatically for +# WPA2-PSK credentials received using WPS. +# 0 = only add the explicitly listed WPA2-PSK configuration (default) +# 1 = add both the WPA2-PSK and SAE configuration and enable PMF so that the +# AP gets configured in WPA3-Personal transition mode (supports both +# WPA2-Personal (PSK) and WPA3-Personal (SAE) clients). +#wps_cred_add_sae=0 + +# AP Settings Attributes for M7 +# By default, hostapd generates the AP Settings Attributes for M7 based on the +# current configuration. It is possible to override this by providing a file +# with pre-configured attributes. This is similar to extra_cred file format, +# but the AP Settings attributes are not encapsulated in a Credential +# attribute. +#ap_settings=hostapd.ap_settings + +# Multi-AP backhaul BSS config +# Used in WPS when multi_ap=2 or 3. Defines "backhaul BSS" credentials. +# These are passed in WPS M8 instead of the normal (fronthaul) credentials +# if the Enrollee has the Multi-AP subelement set. Backhaul SSID is formatted +# like ssid2. The key is set like wpa_psk or wpa_passphrase. +#multi_ap_backhaul_ssid="backhaul" +#multi_ap_backhaul_wpa_psk=0123456789abcdef0123456789abcdef0123456789abcdef0123456789abcdef +#multi_ap_backhaul_wpa_passphrase=secret passphrase + +# WPS UPnP interface +# If set, support for external Registrars is enabled. +#upnp_iface=br0 + +# Friendly Name (required for UPnP) +# Short description for end use. Should be less than 64 characters. +#friendly_name=WPS Access Point + +# Manufacturer URL (optional for UPnP) +#manufacturer_url=http://www.example.com/ + +# Model Description (recommended for UPnP) +# Long description for end user. Should be less than 128 characters. +#model_description=Wireless Access Point + +# Model URL (optional for UPnP) +#model_url=http://www.example.com/model/ + +# Universal Product Code (optional for UPnP) +# 12-digit, all-numeric code that identifies the consumer package. +#upc=123456789012 + +# WPS RF Bands (a = 5G, b = 2.4G, g = 2.4G, ag = dual band, ad = 60 GHz) +# This value should be set according to RF band(s) supported by the AP if +# hw_mode is not set. For dual band dual concurrent devices, this needs to be +# set to ag to allow both RF bands to be advertized. +#wps_rf_bands=ag + +# NFC password token for WPS +# These parameters can be used to configure a fixed NFC password token for the +# AP. This can be generated, e.g., with nfc_pw_token from wpa_supplicant. When +# these parameters are used, the AP is assumed to be deployed with a NFC tag +# that includes the matching NFC password token (e.g., written based on the +# NDEF record from nfc_pw_token). +# +#wps_nfc_dev_pw_id: Device Password ID (16..65535) +#wps_nfc_dh_pubkey: Hexdump of DH Public Key +#wps_nfc_dh_privkey: Hexdump of DH Private Key +#wps_nfc_dev_pw: Hexdump of Device Password + +# Application Extension attribute for Beacon and Probe Response frames +# This parameter can be used to add application extension into WPS IE. The +# contents of this parameter starts with 16-octet (32 hexdump characters) of +# UUID to identify the specific application and that is followed by the actual +# application specific data. +#wps_application_ext=<hexdump> + +##### Wi-Fi Direct (P2P) ###################################################### + +# Enable P2P Device management +#manage_p2p=1 + +# Allow cross connection +#allow_cross_connection=1 + +##### Device Provisioning Protocol (DPP) ###################################### + +# Name for Enrollee's DPP Configuration Request +#dpp_name=Test + +# MUD URL for Enrollee's DPP Configuration Request (optional) +#dpp_mud_url=https://example.com/mud + +#dpp_connector +#dpp_netaccesskey +#dpp_netaccesskey_expiry +#dpp_csign +#dpp_controller + +# Configurator Connectivity indication +# 0: no Configurator is currently connected (default) +# 1: advertise that a Configurator is available +#dpp_configurator_connectivity=0 + +# DPP PFS +# 0: allow PFS to be used or not used (default) +# 1: require PFS to be used (note: not compatible with DPP R1) +# 2: do not allow PFS to be used +#dpp_pfs=0 + +#### TDLS (IEEE 802.11z-2010) ################################################# + +# Prohibit use of TDLS in this BSS +#tdls_prohibit=1 + +# Prohibit use of TDLS Channel Switching in this BSS +#tdls_prohibit_chan_switch=1 + +##### IEEE 802.11v-2011 ####################################################### + +# Time advertisement +# 0 = disabled (default) +# 2 = UTC time at which the TSF timer is 0 +#time_advertisement=2 + +# Local time zone as specified in 8.3 of IEEE Std 1003.1-2004: +# stdoffset[dst[offset][,start[/time],end[/time]]] +#time_zone=EST5 + +# WNM-Sleep Mode (extended sleep mode for stations) +# 0 = disabled (default) +# 1 = enabled (allow stations to use WNM-Sleep Mode) +#wnm_sleep_mode=1 + +# WNM-Sleep Mode GTK/IGTK workaround +# Normally, WNM-Sleep Mode exit with management frame protection negotiated +# would result in the current GTK/IGTK getting added into the WNM-Sleep Mode +# Response frame. Some station implementations may have a vulnerability that +# results in GTK/IGTK reinstallation based on this frame being replayed. This +# configuration parameter can be used to disable that behavior and use EAPOL-Key +# frames for GTK/IGTK update instead. This would likely be only used with +# wpa_disable_eapol_key_retries=1 that enables a workaround for similar issues +# with EAPOL-Key. This is related to station side vulnerabilities CVE-2017-13087 +# and CVE-2017-13088. To enable this AP-side workaround, set the parameter to 1. +#wnm_sleep_mode_no_keys=0 + +# BSS Transition Management +# 0 = disabled (default) +# 1 = enabled +#bss_transition=1 + +# Proxy ARP +# 0 = disabled (default) +# 1 = enabled +#proxy_arp=1 + +# IPv6 Neighbor Advertisement multicast-to-unicast conversion +# This can be used with Proxy ARP to allow multicast NAs to be forwarded to +# associated STAs using link layer unicast delivery. +# 0 = disabled (default) +# 1 = enabled +#na_mcast_to_ucast=0 + +##### IEEE 802.11u-2011 ####################################################### + +# Enable Interworking service +#interworking=1 + +# Access Network Type +# 0 = Private network +# 1 = Private network with guest access +# 2 = Chargeable public network +# 3 = Free public network +# 4 = Personal device network +# 5 = Emergency services only network +# 14 = Test or experimental +# 15 = Wildcard +#access_network_type=0 + +# Whether the network provides connectivity to the Internet +# 0 = Unspecified +# 1 = Network provides connectivity to the Internet +#internet=1 + +# Additional Step Required for Access +# Note: This is only used with open network, i.e., ASRA shall ne set to 0 if +# RSN is used. +#asra=0 + +# Emergency services reachable +#esr=0 + +# Unauthenticated emergency service accessible +#uesa=0 + +# Venue Info (optional) +# The available values are defined in IEEE Std 802.11u-2011, 7.3.1.34. +# Example values (group,type): +# 0,0 = Unspecified +# 1,7 = Convention Center +# 1,13 = Coffee Shop +# 2,0 = Unspecified Business +# 7,1 Private Residence +#venue_group=7 +#venue_type=1 + +# Homogeneous ESS identifier (optional; dot11HESSID) +# If set, this shall be identifical to one of the BSSIDs in the homogeneous +# ESS and this shall be set to the same value across all BSSs in homogeneous +# ESS. +#hessid=02:03:04:05:06:07 + +# Roaming Consortium List +# Arbitrary number of Roaming Consortium OIs can be configured with each line +# adding a new OI to the list. The first three entries are available through +# Beacon and Probe Response frames. Any additional entry will be available only +# through ANQP queries. Each OI is between 3 and 15 octets and is configured as +# a hexstring. +#roaming_consortium=021122 +#roaming_consortium=2233445566 + +# Venue Name information +# This parameter can be used to configure one or more Venue Name Duples for +# Venue Name ANQP information. Each entry has a two or three character language +# code (ISO-639) separated by colon from the venue name string. +# Note that venue_group and venue_type have to be set for Venue Name +# information to be complete. +#venue_name=eng:Example venue +#venue_name=fin:Esimerkkipaikka +# Alternative format for language:value strings: +# (double quoted string, printf-escaped string) +#venue_name=P"eng:Example\nvenue" + +# Venue URL information +# This parameter can be used to configure one or more Venue URL Duples to +# provide additional information corresponding to Venue Name information. +# Each entry has a Venue Number value separated by colon from the Venue URL +# string. Venue Number indicates the corresponding venue_name entry (1 = 1st +# venue_name, 2 = 2nd venue_name, and so on; 0 = no matching venue_name) +#venue_url=1:http://www.example.com/info-eng +#venue_url=2:http://www.example.com/info-fin + +# Network Authentication Type +# This parameter indicates what type of network authentication is used in the +# network. +# format: <network auth type indicator (1-octet hex str)> [redirect URL] +# Network Authentication Type Indicator values: +# 00 = Acceptance of terms and conditions +# 01 = On-line enrollment supported +# 02 = http/https redirection +# 03 = DNS redirection +#network_auth_type=00 +#network_auth_type=02http://www.example.com/redirect/me/here/ + +# IP Address Type Availability +# format: <1-octet encoded value as hex str> +# (ipv4_type & 0x3f) << 2 | (ipv6_type & 0x3) +# ipv4_type: +# 0 = Address type not available +# 1 = Public IPv4 address available +# 2 = Port-restricted IPv4 address available +# 3 = Single NATed private IPv4 address available +# 4 = Double NATed private IPv4 address available +# 5 = Port-restricted IPv4 address and single NATed IPv4 address available +# 6 = Port-restricted IPv4 address and double NATed IPv4 address available +# 7 = Availability of the address type is not known +# ipv6_type: +# 0 = Address type not available +# 1 = Address type available +# 2 = Availability of the address type not known +#ipaddr_type_availability=14 + +# Domain Name +# format: <variable-octet str>[,<variable-octet str>] +#domain_name=example.com,another.example.com,yet-another.example.com + +# 3GPP Cellular Network information +# format: <MCC1,MNC1>[;<MCC2,MNC2>][;...] +#anqp_3gpp_cell_net=244,91;310,026;234,56 + +# NAI Realm information +# One or more realm can be advertised. Each nai_realm line adds a new realm to +# the set. These parameters provide information for stations using Interworking +# network selection to allow automatic connection to a network based on +# credentials. +# format: <encoding>,<NAI Realm(s)>[,<EAP Method 1>][,<EAP Method 2>][,...] +# encoding: +# 0 = Realm formatted in accordance with IETF RFC 4282 +# 1 = UTF-8 formatted character string that is not formatted in +# accordance with IETF RFC 4282 +# NAI Realm(s): Semi-colon delimited NAI Realm(s) +# EAP Method: <EAP Method>[:<[AuthParam1:Val1]>][<[AuthParam2:Val2]>][...] +# EAP Method types, see: +# http://www.iana.org/assignments/eap-numbers/eap-numbers.xhtml#eap-numbers-4 +# AuthParam (Table 8-188 in IEEE Std 802.11-2012): +# ID 2 = Non-EAP Inner Authentication Type +# 1 = PAP, 2 = CHAP, 3 = MSCHAP, 4 = MSCHAPV2 +# ID 3 = Inner authentication EAP Method Type +# ID 5 = Credential Type +# 1 = SIM, 2 = USIM, 3 = NFC Secure Element, 4 = Hardware Token, +# 5 = Softoken, 6 = Certificate, 7 = username/password, 9 = Anonymous, +# 10 = Vendor Specific +#nai_realm=0,example.com;example.net +# EAP methods EAP-TLS with certificate and EAP-TTLS/MSCHAPv2 with +# username/password +#nai_realm=0,example.org,13[5:6],21[2:4][5:7] + +# Arbitrary ANQP-element configuration +# Additional ANQP-elements with arbitrary values can be defined by specifying +# their contents in raw format as a hexdump of the payload. Note that these +# values will override ANQP-element contents that may have been specified in the +# more higher layer configuration parameters listed above. +# format: anqp_elem=<InfoID>:<hexdump of payload> +# For example, AP Geospatial Location ANQP-element with unknown location: +#anqp_elem=265:0000 +# For example, AP Civic Location ANQP-element with unknown location: +#anqp_elem=266:000000 + +# GAS Address 3 behavior +# 0 = P2P specification (Address3 = AP BSSID) workaround enabled by default +# based on GAS request Address3 +# 1 = IEEE 802.11 standard compliant regardless of GAS request Address3 +# 2 = Force non-compliant behavior (Address3 = AP BSSID for all cases) +#gas_address3=0 + +# QoS Map Set configuration +# +# Comma delimited QoS Map Set in decimal values +# (see IEEE Std 802.11-2012, 8.4.2.97) +# +# format: +# [<DSCP Exceptions[DSCP,UP]>,]<UP 0 range[low,high]>,...<UP 7 range[low,high]> +# +# There can be up to 21 optional DSCP Exceptions which are pairs of DSCP Value +# (0..63 or 255) and User Priority (0..7). This is followed by eight DSCP Range +# descriptions with DSCP Low Value and DSCP High Value pairs (0..63 or 255) for +# each UP starting from 0. If both low and high value are set to 255, the +# corresponding UP is not used. +# +# default: not set +#qos_map_set=53,2,22,6,8,15,0,7,255,255,16,31,32,39,255,255,40,47,255,255 + +##### Hotspot 2.0 ############################################################# + +# Enable Hotspot 2.0 support +#hs20=1 + +# Disable Downstream Group-Addressed Forwarding (DGAF) +# This can be used to configure a network where no group-addressed frames are +# allowed. The AP will not forward any group-address frames to the stations and +# random GTKs are issued for each station to prevent associated stations from +# forging such frames to other stations in the BSS. +#disable_dgaf=1 + +# OSU Server-Only Authenticated L2 Encryption Network +#osen=1 + +# ANQP Domain ID (0..65535) +# An identifier for a set of APs in an ESS that share the same common ANQP +# information. 0 = Some of the ANQP information is unique to this AP (default). +#anqp_domain_id=1234 + +# Deauthentication request timeout +# If the RADIUS server indicates that the station is not allowed to connect to +# the BSS/ESS, the AP can allow the station some time to download a +# notification page (URL included in the message). This parameter sets that +# timeout in seconds. +#hs20_deauth_req_timeout=60 + +# Operator Friendly Name +# This parameter can be used to configure one or more Operator Friendly Name +# Duples. Each entry has a two or three character language code (ISO-639) +# separated by colon from the operator friendly name string. +#hs20_oper_friendly_name=eng:Example operator +#hs20_oper_friendly_name=fin:Esimerkkioperaattori + +# Connection Capability +# This can be used to advertise what type of IP traffic can be sent through the +# hotspot (e.g., due to firewall allowing/blocking protocols/ports). +# format: <IP Protocol>:<Port Number>:<Status> +# IP Protocol: 1 = ICMP, 6 = TCP, 17 = UDP +# Port Number: 0..65535 +# Status: 0 = Closed, 1 = Open, 2 = Unknown +# Each hs20_conn_capab line is added to the list of advertised tuples. +#hs20_conn_capab=1:0:2 +#hs20_conn_capab=6:22:1 +#hs20_conn_capab=17:5060:0 + +# WAN Metrics +# format: <WAN Info>:<DL Speed>:<UL Speed>:<DL Load>:<UL Load>:<LMD> +# WAN Info: B0-B1: Link Status, B2: Symmetric Link, B3: At Capabity +# (encoded as two hex digits) +# Link Status: 1 = Link up, 2 = Link down, 3 = Link in test state +# Downlink Speed: Estimate of WAN backhaul link current downlink speed in kbps; +# 1..4294967295; 0 = unknown +# Uplink Speed: Estimate of WAN backhaul link current uplink speed in kbps +# 1..4294967295; 0 = unknown +# Downlink Load: Current load of downlink WAN connection (scaled to 255 = 100%) +# Uplink Load: Current load of uplink WAN connection (scaled to 255 = 100%) +# Load Measurement Duration: Duration for measuring downlink/uplink load in +# tenths of a second (1..65535); 0 if load cannot be determined +#hs20_wan_metrics=01:8000:1000:80:240:3000 + +# Operating Class Indication +# List of operating classes the BSSes in this ESS use. The Global operating +# classes in Table E-4 of IEEE Std 802.11-2012 Annex E define the values that +# can be used in this. +# format: hexdump of operating class octets +# for example, operating classes 81 (2.4 GHz channels 1-13) and 115 (5 GHz +# channels 36-48): +#hs20_operating_class=5173 + +# Terms and Conditions information +# +# hs20_t_c_filename contains the Terms and Conditions filename that the AP +# indicates in RADIUS Access-Request messages. +#hs20_t_c_filename=terms-and-conditions +# +# hs20_t_c_timestamp contains the Terms and Conditions timestamp that the AP +# indicates in RADIUS Access-Request messages. Usually, this contains the number +# of seconds since January 1, 1970 00:00 UTC showing the time when the file was +# last modified. +#hs20_t_c_timestamp=1234567 +# +# hs20_t_c_server_url contains a template for the Terms and Conditions server +# URL. This template is used to generate the URL for a STA that needs to +# acknowledge Terms and Conditions. Unlike the other hs20_t_c_* parameters, this +# parameter is used on the authentication server, not the AP. +# Macros: +# @1@ = MAC address of the STA (colon separated hex octets) +#hs20_t_c_server_url=https://example.com/t_and_c?addr=@1@&ap=123 + +# OSU and Operator icons +# <Icon Width>:<Icon Height>:<Language code>:<Icon Type>:<Name>:<file path> +#hs20_icon=32:32:eng:image/png:icon32:/tmp/icon32.png +#hs20_icon=64:64:eng:image/png:icon64:/tmp/icon64.png + +# OSU SSID (see ssid2 for format description) +# This is the SSID used for all OSU connections to all the listed OSU Providers. +#osu_ssid="example" + +# OSU Providers +# One or more sets of following parameter. Each OSU provider is started by the +# mandatory osu_server_uri item. The other parameters add information for the +# last added OSU provider. osu_nai specifies the OSU_NAI value for OSEN +# authentication when using a standalone OSU BSS. osu_nai2 specifies the OSU_NAI +# value for OSEN authentication when using a shared BSS (Single SSID) for OSU. +# +#osu_server_uri=https://example.com/osu/ +#osu_friendly_name=eng:Example operator +#osu_friendly_name=fin:Esimerkkipalveluntarjoaja +#osu_nai=anonymous@example.com +#osu_nai2=anonymous@example.com +#osu_method_list=1 0 +#osu_icon=icon32 +#osu_icon=icon64 +#osu_service_desc=eng:Example services +#osu_service_desc=fin:Esimerkkipalveluja +# +#osu_server_uri=... + +# Operator Icons +# Operator icons are specified using references to the hs20_icon entries +# (Name subfield). This information, if present, is advertsised in the +# Operator Icon Metadata ANQO-element. +#operator_icon=icon32 +#operator_icon=icon64 + +##### Multiband Operation (MBO) ############################################### +# +# MBO enabled +# 0 = disabled (default) +# 1 = enabled +#mbo=1 +# +# Cellular data connection preference +# 0 = Excluded - AP does not want STA to use the cellular data connection +# 1 = AP prefers the STA not to use cellular data connection +# 255 = AP prefers the STA to use cellular data connection +#mbo_cell_data_conn_pref=1 + +##### Optimized Connectivity Experience (OCE) ################################# +# +# Enable OCE specific features (bitmap) +# BIT(0) - Reserved +# Set BIT(1) (= 2) to enable OCE in STA-CFON mode +# Set BIT(2) (= 4) to enable OCE in AP mode +# Default is 0 = OCE disabled +#oce=0 + +# RSSI-based association rejection +# +# Reject STA association if RSSI is below given threshold (in dBm) +# Allowed range: -60 to -90 dBm; default = 0 (rejection disabled) +# Note: This rejection happens based on a signal strength detected while +# receiving a single frame and as such, there is significant risk of the value +# not being accurate and this resulting in valid stations being rejected. As +# such, this functionality is not recommended to be used for purposes other than +# testing. +#rssi_reject_assoc_rssi=-75 +# +# Association retry delay in seconds allowed by the STA if RSSI has not met the +# threshold (range: 0..255, default=30). +#rssi_reject_assoc_timeout=30 + +# Ignore Probe Request frames if RSSI is below given threshold (in dBm) +# Allowed range: -60 to -90 dBm; default = 0 (rejection disabled) +#rssi_ignore_probe_request=-75 + +##### Fast Session Transfer (FST) support ##################################### +# +# The options in this section are only available when the build configuration +# option CONFIG_FST is set while compiling hostapd. They allow this interface +# to be a part of FST setup. +# +# FST is the transfer of a session from a channel to another channel, in the +# same or different frequency bands. +# +# For detals, see IEEE Std 802.11ad-2012. + +# Identifier of an FST Group the interface belongs to. +#fst_group_id=bond0 + +# Interface priority within the FST Group. +# Announcing a higher priority for an interface means declaring it more +# preferable for FST switch. +# fst_priority is in 1..255 range with 1 being the lowest priority. +#fst_priority=100 + +# Default LLT value for this interface in milliseconds. The value used in case +# no value provided during session setup. Default is 50 ms. +# fst_llt is in 1..4294967 range (due to spec limitation, see 10.32.2.2 +# Transitioning between states). +#fst_llt=100 + +##### Radio measurements / location ########################################### + +# The content of a LCI measurement subelement +#lci=<Hexdump of binary data of the LCI report> + +# The content of a location civic measurement subelement +#civic=<Hexdump of binary data of the location civic report> + +# Enable neighbor report via radio measurements +#rrm_neighbor_report=1 + +# Enable beacon report via radio measurements +#rrm_beacon_report=1 + +# Publish fine timing measurement (FTM) responder functionality +# This parameter only controls publishing via Extended Capabilities element. +# Actual functionality is managed outside hostapd. +#ftm_responder=0 + +# Publish fine timing measurement (FTM) initiator functionality +# This parameter only controls publishing via Extended Capabilities element. +# Actual functionality is managed outside hostapd. +#ftm_initiator=0 +# +# Stationary AP config indicates that the AP doesn't move hence location data +# can be considered as always up to date. If configured, LCI data will be sent +# as a radio measurement even if the request doesn't contain a max age element +# that allows sending of such data. Default: 0. +#stationary_ap=0 + +# Enable reduced neighbor reporting (RNR) +#rnr=0 + +##### Airtime policy configuration ########################################### + +# Set the airtime policy operating mode: +# 0 = disabled (default) +# 1 = static config +# 2 = per-BSS dynamic config +# 3 = per-BSS limit mode +#airtime_mode=0 + +# Interval (in milliseconds) to poll the kernel for updated station activity in +# dynamic and limit modes +#airtime_update_interval=200 + +# Static configuration of station weights (when airtime_mode=1). Kernel default +# weight is 256; set higher for larger airtime share, lower for smaller share. +# Each entry is a MAC address followed by a weight. +#airtime_sta_weight=02:01:02:03:04:05 256 +#airtime_sta_weight=02:01:02:03:04:06 512 + +# Per-BSS airtime weight. In multi-BSS mode, set for each BSS and hostapd will +# configure station weights to enforce the correct ratio between BSS weights +# depending on the number of active stations. The *ratios* between different +# BSSes is what's important, not the absolute numbers. +# Must be set for all BSSes if airtime_mode=2 or 3, has no effect otherwise. +#airtime_bss_weight=1 + +# Whether the current BSS should be limited (when airtime_mode=3). +# +# If set, the BSS weight ratio will be applied in the case where the current BSS +# would exceed the share defined by the BSS weight ratio. E.g., if two BSSes are +# set to the same weights, and one is set to limited, the limited BSS will get +# no more than half the available airtime, but if the non-limited BSS has more +# stations active, that *will* be allowed to exceed its half of the available +# airtime. +#airtime_bss_limit=1 + +##### EDMG support ############################################################ +# +# Enable EDMG capability for AP mode in the 60 GHz band. Default value is false. +# To configure channel bonding for an EDMG AP use edmg_channel below. +# If enable_edmg is set and edmg_channel is not set, EDMG CB1 will be +# configured. +#enable_edmg=1 +# +# Configure channel bonding for AP mode in the 60 GHz band. +# This parameter is relevant only if enable_edmg is set. +# Default value is 0 (no channel bonding). +#edmg_channel=9 + +##### TESTING OPTIONS ######################################################### +# +# The options in this section are only available when the build configuration +# option CONFIG_TESTING_OPTIONS is set while compiling hostapd. They allow +# testing some scenarios that are otherwise difficult to reproduce. +# +# Ignore probe requests sent to hostapd with the given probability, must be a +# floating point number in the range [0, 1). +#ignore_probe_probability=0.0 +# +# Ignore authentication frames with the given probability +#ignore_auth_probability=0.0 +# +# Ignore association requests with the given probability +#ignore_assoc_probability=0.0 +# +# Ignore reassociation requests with the given probability +#ignore_reassoc_probability=0.0 +# +# Corrupt Key MIC in GTK rekey EAPOL-Key frames with the given probability +#corrupt_gtk_rekey_mic_probability=0.0 +# +# Include only ECSA IE without CSA IE where possible +# (channel switch operating class is needed) +#ecsa_ie_only=0 + +##### Multiple BSSID support ################################################## +# +# Above configuration is using the default interface (wlan#, or multi-SSID VLAN +# interfaces). Other BSSIDs can be added by using separator 'bss' with +# default interface name to be allocated for the data packets of the new BSS. +# +# hostapd will generate BSSID mask based on the BSSIDs that are +# configured. hostapd will verify that dev_addr & MASK == dev_addr. If this is +# not the case, the MAC address of the radio must be changed before starting +# hostapd (ifconfig wlan0 hw ether <MAC addr>). If a BSSID is configured for +# every secondary BSS, this limitation is not applied at hostapd and other +# masks may be used if the driver supports them (e.g., swap the locally +# administered bit) +# +# BSSIDs are assigned in order to each BSS, unless an explicit BSSID is +# specified using the 'bssid' parameter. +# If an explicit BSSID is specified, it must be chosen such that it: +# - results in a valid MASK that covers it and the dev_addr +# - is not the same as the MAC address of the radio +# - is not the same as any other explicitly specified BSSID +# +# Alternatively, the 'use_driver_iface_addr' parameter can be used to request +# hostapd to use the driver auto-generated interface address (e.g., to use the +# exact MAC addresses allocated to the device). +# +# Not all drivers support multiple BSSes. The exact mechanism for determining +# the driver capabilities is driver specific. With the current (i.e., a recent +# kernel) drivers using nl80211, this information can be checked with "iw list" +# (search for "valid interface combinations"). +# +# Please note that hostapd uses some of the values configured for the first BSS +# as the defaults for the following BSSes. However, it is recommended that all +# BSSes include explicit configuration of all relevant configuration items. +# +#bss=wlan0_0 +#ssid=test2 +# most of the above items can be used here (apart from radio interface specific +# items, like channel) + +#bss=wlan0_1 +#bssid=00:13:10:95:fe:0b +# ... +#} |