| Age | Commit message (Collapse) | Author |
|---|
|
|
|
bridge: T3042: Support VLAN filter and VLAN sub-interface on the bridge
|
|
This commit has to do with the addition of miscellaneous MPLS parameters, as well as miscellaneous LDP parameters. Per c-po, for miscellaneous options and whatnot that do not fit anywhere we will put them into a specific "parameters" node.
I also did some global linux configuration changes here. We make changes to kernel options "net.mpls.ip_ttl_propagate" and "net.mpls.default_ttl" which should allow the behavior of VyOS to have the same as routers from the big vendors.
I added two LDP options for cisco interoperation TLV and for a dual stack preference.
Lastly, I went through and changes some of the help/description fields in the definitions page because I just felt they weren't uniform and the words seemed to not properly explain what they were doing. I also did some code clean up (or tried to...) with comments and whatnot.
|
|
A non existing device usb0b1.4p1.?? device was not detected, as find_device_file()
returned None which can not be passed into os.path.exists().
Traceback (most recent call last):
File "/usr/libexec/vyos/conf_mode/interfaces-wirelessmodem.py", line 126, in <module>
verify(c)
File "/usr/libexec/vyos/conf_mode/interfaces-wirelessmodem.py", line 60, in verify
if dev_path is None or os.path.exists(find_device_file(dev_path)):
File "/usr/lib/python3.7/genericpath.py", line 19, in exists
os.stat(path)
TypeError: stat: path should be string, bytes, os.PathLike or integer, not NoneType
|
|
|
|
mpls-conf: T915: Add targeted LDP neighbors with parameters
|
|
The commit has to do with the addition of targeted LDP neighbors and parameters being added. FRR allows for this functionality and I just wanted to add it.
We have basically 4 options that are added. Enabling targeted LDP functionality, the targeted neighbor, the hello interval of targeted sessions, and the hold time of targeted sessions. Both IPv4 and IPv6 has been coded in.
|
|
Some might want to have an IP address handed out by a DHCP server but not want
a default route to be installed. This can be done using the CLI command:
"set interfaces ethernet eth2 dhcp-options no-default-route"
|
|
|
|
|
|
|
|
|
|
This reduces duplicated #include statements as each interface type already
contained the individual includes.
|
|
|
|
There has been a miss-match of admin-down and oper-down status for the Python
implementation of "show interfaces".
|
|
|
|
|
|
Add new CLI command "set system options performance <latency | throughput>"
|
|
|
|
mpls-conf: T915: Add session hold time adjustment for LDP neighbors
|
|
The commit has to do with the addition of session hold time parameter for LDP neighbors. This allows for being able to change said hold time on a static neighbor.
The way that this works is to have it either delegated to a value (15-65535), or to just be default to whatever FRR stipulates or per the other session configuration values.
I opted to remove the "-ipv4-" only because we know it's an IPv4 session that one has to create first. I figure it's redundant to add it there so I removed it.
|
|
mpls-conf: T915: Add TTL security for static LDP neighbors
|
|
The commit has to do with the addition of TTL security for LDP neighbors. The code was 90% done by Viascheslav. I modified it a little bit to get it to properly work.
We added more parameters to the neighbors dynamic loop. Once this is merged then we should be able to add more for the dynamic neighbor statements.
The way that this works is to have either TTL disabled, or to add the amount of hops accepted for the neighbor.
|
|
This commit partially reverts commit eb1ed5e518 ("openvpn: T2994: re-add
ifconfig-pool statement in server config").
|
|
* 'wifi-wpa3' of github.com:c-po/vyos-1x:
wireless: T3042: move wifi-regulatory-domain into individual interface definition
wireless: T2653: reset wireless priority to crux state
wireless: T3034: add WPA3 support
wireless: T3043: rename "wpa mode both" to "wpa+wpa2"
ifconfig: T2985: fix wireless-bridge creation
|
|
definition
|
|
conf-mode: T2103: Delete value help match en[ospx]N for eth interfaces
|
|
mpls-conf: T915: Separate IPv4 and IPv6 hello timers, add IPv6 timers
|
|
T2465: Fixing permissions on socket so DHCP works
|
|
bgp-xml: T2387: Fix validators for neighbor update-source
|
|
|
|
|
|
Now as we can dynamically create bridge interfaces we can also reset the interface
priority back to the value it used to be in VyOS 1.2 crux.
|
|
|
|
|
|
|
|
bgp: T2850: Fixing the priority of template processing and missing params
|
|
|
|
bgp-xml: T2387: Fix validators and add capability for new format bgp
|
|
|
|
There have been leftovers to bypass testcases by simply just "return True" on
most of the testcases.
|
|
|
|
Re-organize the template code and add addtitional Jinja2 filters for processing
the ifconfig-pool statement. This reverts the changes from commit 7e546be9
("openvpn: T2994: temporary revert to 1.2 crux behavior for client pools").
|
|
Test additional network combinations of address and prefixes.
|
|
|
|
Remove workaround which split (local|remote)_address and also subnet keys into
individual keys for the assigned IP address family (4/6).
During template rendering check IP version by introducing new ipv4 and ipv6
Jinja2 filters {% if foo | ipv4 %} or {% if bar | ipv6 %} options.
|
|
After renaming the function in commit 25551c5a ("vyos.util: T2995: rename
vyos_dict_search() -> dict_search()"), the test case should be renamed, too.
|
|
|
|
|
|
After commit 7e546be921 ("openvpn: T2994: temporary revert to 1.2 crux behavior
for client pools") also adjust the testcase to not expect the "nopool" statement
on the server command.
|
