| Age | Commit message (Collapse) | Author |
|---|
|
Python value
We should not use hardcoded Python values whenever possible. vyos.xml provides
an abstraction of the XML CLI definitions providing default values from the CLI
specified via the <defaultValue> node.
This increases consistency among all XML/Python wrappers.
Additional small fixes in this commit (besides the bad practice incorporating
unrelated changes into the same commit) contain:
- Keyboard layout shout be explicitly set for /dev/console
- Added missing Debian dependency on console-data
- When looking for a key in a dict, we do not need to specify dict.keys()
|
|
Revert "T2802: Tunnel interface does not apply EUI-64 IPv6 Address"
|
|
Revert "T3068: Automatic generation of IPv6 link local addresses for tunnel interfaces"
|
|
|
|
interfaces"
|
|
system: T3038: Add keyboard layout CLI command
|
|
T2802: Tunnel interface does not apply EUI-64 IPv6 Address
|
|
|
|
Generate an IPv6 Link Local address for wireguard interfaces.
|
|
* 't1316-frr-isis' of github.com:c-po/vyos-1x:
isis: T1316: refactor config retrieval and Jinja2 template
isis: T1316: October steps
|
|
Make the entire template code more human readable by denesting it, as there can
only be one ISIS daemon instance in FRR.
|
|
powerctl: T3066: Calculate minutes over 60
|
|
T3068: Automatic generation of IPv6 link local addresses for tunnel interfaces
|
|
T3060: Fixing a backwards check on dh length
|
|
openvpn: T3060: Remote-host is a required param for client
|
|
|
|
|
|
t1616-isis
* 'T1316_october' of https://github.com/sever-sever/vyos-1x:
isis: T1316: October steps
|
|
|
|
After commit 943a4a50 ("openvpn: T3051: fix creation of ifconfig-pool for
client communication") the smoketests had nod been adjusted correctly.
This has been fixed.
|
|
We had two places were the is_ip, is_ipv4 and is_ipv6 helpers had been defined.
All places now have been converged into vyos.template as they are used both
in the Jinja2 templates and also in our scripts.
|
|
|
|
Better implementation to assign link local addresses automatically because address only assigned to interfaces which supports IPv6 addresses.
|
|
Tunnel interfaces hot having any IPv6 Link Local address because Linux Kernel does not assign address due to missing MAC. I have implemented a function to generate a linl local address and assign it to the interface. Link local address is required for OSPF and other protocols.
|
|
|
|
|
|
bridge: T3042: Fix VLAN filter invalid work
|
|
1. Due to the previous focus on the implementation of VLAN filter, it was not considered to include MTU settings, which will lead to MTU setting errors in some cases
2. In order to make VLAN aware of the work of the bridge, it is necessary to specify the allowed VLAN ID range for the bridge itself, and forget to join it before
|
|
This is no longer required after commit for the VyOS Kernel configuration
https://github.com/vyos/vyos-build/commit/3fa7fe6926a538a8b4f25
|
|
|
|
Commit a1327d2b970 ("ssh: T2635: reuse common verify_vrf() function") already
moved to the common verify logic but did not remove the no longer needed import
statement.
|
|
bgp-new: T2174: Fix abbility to del global route-map param
|
|
|
|
bridge: T3042: Support VLAN filter and VLAN sub-interface on the bridge
|
|
|
|
This commit has to do with the addition of miscellaneous MPLS parameters, as well as miscellaneous LDP parameters. Per c-po, for miscellaneous options and whatnot that do not fit anywhere we will put them into a specific "parameters" node.
I also did some global linux configuration changes here. We make changes to kernel options "net.mpls.ip_ttl_propagate" and "net.mpls.default_ttl" which should allow the behavior of VyOS to have the same as routers from the big vendors.
I added two LDP options for cisco interoperation TLV and for a dual stack preference.
Lastly, I went through and changes some of the help/description fields in the definitions page because I just felt they weren't uniform and the words seemed to not properly explain what they were doing. I also did some code clean up (or tried to...) with comments and whatnot.
|
|
A non existing device usb0b1.4p1.?? device was not detected, as find_device_file()
returned None which can not be passed into os.path.exists().
Traceback (most recent call last):
File "/usr/libexec/vyos/conf_mode/interfaces-wirelessmodem.py", line 126, in <module>
verify(c)
File "/usr/libexec/vyos/conf_mode/interfaces-wirelessmodem.py", line 60, in verify
if dev_path is None or os.path.exists(find_device_file(dev_path)):
File "/usr/lib/python3.7/genericpath.py", line 19, in exists
os.stat(path)
TypeError: stat: path should be string, bytes, os.PathLike or integer, not NoneType
|
|
|
|
mpls-conf: T915: Add targeted LDP neighbors with parameters
|
|
The commit has to do with the addition of targeted LDP neighbors and parameters being added. FRR allows for this functionality and I just wanted to add it.
We have basically 4 options that are added. Enabling targeted LDP functionality, the targeted neighbor, the hello interval of targeted sessions, and the hold time of targeted sessions. Both IPv4 and IPv6 has been coded in.
|
|
Some might want to have an IP address handed out by a DHCP server but not want
a default route to be installed. This can be done using the CLI command:
"set interfaces ethernet eth2 dhcp-options no-default-route"
|
|
|
|
|
|
|
|
|
|
This reduces duplicated #include statements as each interface type already
contained the individual includes.
|
|
|
|
There has been a miss-match of admin-down and oper-down status for the Python
implementation of "show interfaces".
|
|
|
|
|
