| Age | Commit message (Collapse) | Author |
|---|
|
Co-authored-by: Christian Breunig <christian@breunig.cc>
|
|
|
|
Changes:
1. Change option space from 'ubnt' to 'vendor-encapsulated-options-space'.
2. Change option name from 'unifi-controller' to 'ubnt'.
3. Add 'vendor-encapsulated-options' option (in addition to adding unifi
controller IP address under the option name 'ubnt') if unifi-controller
is configured.
|
|
FRR (#4994)
* sr-te: T6750: Adding Segment Routing Traffic Engineering portion of FRR
---------
Co-authored-by: Cheeze_It <none@none.com>
Co-authored-by: Christian Breunig <christian@breunig.cc>
|
|
Setting a timeout allows VRRP health-check scripts to run longer than the set interval.
Without timeout, keepalived considers the script as failed after interval seconds.
With timeout set higher than interval, the script has more time to complete
before being marked as failed and transitioning VRRP to FAULT state.
|
|
vpp: T8460: Use isolated cpus for VPP cpu-cores
|
|
VPP CPU core assignment now uses kernel-isolated CPUs (from /sys/devices/system/cpu/isolated) with explicit corelist-workers instead of computing offsets from available cores with skip-cores/workers. Added validation that enough CPUs are actually isolated before VPP starts, and that isolate-cpus config only references existing CPU IDs. Moved smoketest for kernel option 'isolate-cpus' to test_vpp.py
|
|
|
|
Internal typo/cosmitic bug, no functional changes
|
|
T8448: add an option to enable SNMP traps in VRRP
|
|
Allow to configure Keepalived VRRP traps
- set high-availability vrrp snmp trap
|
|
|
|
T8229: Fix handling of endpoint in Telegraf Loki template
|
|
bgp: T7338: Add support for "parameters as-notation <asdot|asdot+>"
|
|
|
|
We explicitly omit the "plain" option, as it is the implicit default in FRR
We also do not want to add "plain" as VyOS default value and emit it by default
as this makes the config a bit ugly (frr puts it in the router line so you get
"router bgp <AS> as-notation plain").
Additionally, setting plain as default value and emitting it by default would
break pretty much all BGP tests, as they commonly do
self.getFRRconfig(f'router bgp {ASN}', stop_section='^exit')
and getFRRConfig does a "^<content>$" match, which breaks when you add the
"as-notation plain"
|
|
Fix typos and mistakes
No functional changes
|
|
T8410: Fix typos and mistakes for operational and configuration commands
|
|
Commit 5c800be95 ("T8405: fix noipv6 emitted when dhcpv6-options configured
without ipv6 node") added a superfluous +, most likely due to a rebase or
merge error.
|
|
Fix typos and mistakes in the commands and comments
No functional changes
|
|
When a PPPoE interface has dhcpv6-options (e.g. prefix delegation)
configured but no explicit ipv6 node, the Jinja template writes
noipv6 into the PPP peer configuration. This prevents IPv6CP
negotiation, causing the ISP to silently ignore all DHCPv6 traffic.
Fix the peer template to also check for dhcpv6_options before emitting
noipv6, and add dhcpv6-options and ipv6 to the list of config nodes
that trigger a PPPoE session restart so the change takes effect
without manual disconnect/reconnect.
|
|
T8386: fix locat_ts rendering in remote_access.j2
|
|
|
|
|
|
|
|
|
|
section
|
|
Co-Authored-by: Christian Breunig <christian@breunig.cc>
|
|
|
|
ospf: T7679: fix plaintext authentication on specific interface
|
|
|
|
|
|
Replace single '=' with '==' in GRUB shell conditionals for
string comparisons
|
|
T8120: Add support AMA console for ARM devices
|
|
IPv6 wildcard prefix derivation and includes validation and smoketests.
Included changes:
- Add `base-interface` under:
- `service router-advert interface <lan-if> prefix ::/64 base-interface <wan-if>`
- Render `Base6Interface <wan-if>;` in `radvd.conf` when configured.
- Add validation guard:
- `base-interface` is only allowed with wildcard prefix `::/64`.
- Extend smoketests:
- Positive case: `::/64` + `base-interface` commits and renders correctly.
- Negative case: non-`::/64` prefix with `base-interface` fails commit.
|
|
|
|
srv6: T6977: add srv6 encapsulation source-address
|
|
Remove `dpdk-options` under `set vpp settings interface <ethN>`
and move its child options to the interface level:
- `num-rx-desc`
- `num-rx-queues`
- `num-tx-desc`
- `num-tx-queues`
Also remove `set vpp settings interface <ethN> dpdk-options promisc`.
|
|
Co-authored-by: Copilot <175728472+Copilot@users.noreply.github.com>
|
|
|
|
syslog: T8272: remove dead code from previous "file" logging support
|
|
Commit 395e3cb72 ("syslog: T6989: remove 'file' logging destination") removed
CLI support for custom file based logging targets. The code about logrotate
was not removed and just stayed "dead".
Dead code is removed by this commit.
|
|
vpp: T8268: Unify CPU settings into a single 'cpu-cores' node under 'resource-allocation'
|
|
'resource-allocation'
Replace legacy VPP CPU settings (main-core, skip-cores, workers, corelist-workers) with a single resource-allocation cpu-cores option.
CPU assignment is now handled automatically: two cores are reserved for the system, the VPP main thread is placed on the first available core, and the remaining allocated cores are used as workers.
This simplifies configuration and ensures consistent CPU allocation.
|
|
lcd: T8213: add support for MTC S16209x
|
|
|
|
Instead of `vpp settings unix poll-sleep-usec`
use `vpp settings poll-sleep-usec`.
|
|
Implementation has been tested using a virtual serial pipe as I (Christian
Breunig) did not find my hardware LCD display. You can easily do this via:
$ sudo socat -d -d PTY,link=/dev/ttyS99,raw,echo=0 PTY,link=/tmp/serial,raw,echo=0
$ sudo cat /tmp/serial
You will get a lot of control characters, but real information like the OS
Kernel version will scroll through.
Co-authored-by: Christian Breunig <christian@breunig.cc>
|
|
|
|
This commit changes logging settings naming:
- before: `set vpp settings logging default-log-level <alert>`
- after: `set vpp settings logging default-level <alert>`
|
