| Age | Commit message (Collapse) | Author |
|---|
|
|
|
dhcp: T2562: add "listen-address" CLI node for better DHCP relay support
|
|
mpls-conf: T915: Add LDP local label allocation control
|
|
|
|
Running ISC DHCP server as backend server for multiple pools served to relay
agents requires DHCPd to explicitly listen on give interfaces or a "transit"
subnet declaration facing the network where we receive the DHCPREQ messages on.
This implements a new "listen-address" CLI node, the given address is validated
if it is assigned to the system and upon success, a proper "subnet { }" statement
is added into dhcpd.conf
|
|
While rewriting the code to get_config_dict() in commit 84b7ade286 ("dhcp: T3100:
migrate server configuration to get_config_dict()") a regression was added not
properly joining strings when multiple search-somains had been given.
Wrong: domain-search "domain1, domain2";
Correct: domain-search "domain1", "domain2";
|
|
In this commit we added the ability to control the local label allocation
control for FECs. It allows for the router to not allocate a label for every
interface, just the interfaces that are desired by the operator.
|
|
|
|
IPv6 enable can be considered once the ipv6 node is present!
|
|
isis: T1316: Fix isis delete section. Use an updated frr framework
|
|
|
|
Commit c87ad948999 ("vyos.template: T2720: fix remaining in-line time_block
syntax") did not take into account when there is an if/endif statement on one
line, the following new-line will be discarded.
|
|
|
|
|
|
|
|
- Upstream interfaces require a DHCPv6 server to be configured
- Listen interface must have a a global unicast address assigned, else
ISC dhcrelay won't start.
|
|
|
|
|
|
set system ntp server <server> pool
|
|
|
|
|
|
The NAT system consists out of nested tag nodes which makes manual parsing very
hard. This is a perfect candidate for migrating this to get_config_dict() as
there is already a smoketest in place.
In addition this should make it easier to add features like static nat/hairpin.
|
|
Commit a2ac9fac ("vyos.template: T2720: always enable Jinja2 trim_blocks
feature") globally enabled the trim_blocks feature. Some templates still used
in-line trim_blocks "{%"- or "-%}" which caused miss-placed line endings.
This is fixed by removing all in-line trim_block statememnts of Jinja2 templates.
|
|
After commit a2ac9fac16eeb626d3969092fecf463650750640 remove no longer
required template trim block statements.
|
|
|
|
Trimming blocks manually is not needed as the renderer is already called with
the 'trim_blocks' option.
|
|
When rendering the configs "ifconfig" statement wrong IP addresses have been
used for the "tun" operating mode. This has been corrected.
|
|
mpls-conf: T915: Refactored template, handler, added global features
|
|
global features
So this is a big update.
The first thing that was done was a refactor to the FRR LDP template, MPLS handler, and XML conf tree MPLS global additions.
The refactors should work and I did test them in my lab. It seems that everything does work as needed so far in my testing.
There is something here that is considered configuration breaking from the old setup though. In the old setup the MPLS interface operation (as in the interfaces accepting MPLS labels and processing them) was tied with LDP. What this means is that MPLS processing was enabled at the same time as LDP interfaces were configured. We do not want this behavior for the future as there's other MPLS underlay technologies like SR and RSVP. If someone wants to enable SR or RSVP without enabling LDP then they now can. Before, they couldn't. The other additions are global changes to MPLS TTL propagation and MPLS max TTL enforcement. They have now been added.
Lastly, there is an frr-reload bug that Runar Borge found with this. We have found that when totally deleting LDP that there has to be 3 commits done. This is because frr-reload doesn't properly do what it needs to do in 1 operation so we had to do 3. This will only affect people that are doing an entire LDP clear using "delete protocols mpls ldp." Otherwise it isn't seen.
Anyway, this refactor now works with the FRR daemon directly for all changes. This also makes it much easier for adding stuff in the future.
Thank you
|
|
The Jinja2 template contained a lot of redundant paths which only differed in
either the address-family or neighbor vs. peer-group. This paths have been
combined into for loops and a macro for generating a neighbor statement as
peer-groups and regular neighbors share ~95% of the config.
|
|
|
|
|
|
|
|
This reverts commit 806f35b5856c3f8dae634718a6a9e82cc90bb63a.
Unfortunately this did not work our in the attempt to bridge a station to a
bridge "brX" interface. Also adjusting the wireless interface during operation
cause several exceptions and the feature is removed again as it was never in any
production system.
|
|
setting this to udp will allow both IPv4 and IPv6 connections. According to the
MAN page: proto indicates the protocol to use when connecting with the remote,
and may be "tcp" or "udp". For forcing IPv4 or IPv6 connection suffix tcp or
udp with 4/6 like udp4/udp6/tcp4/tcp6.
|
|
Make the entire template code more human readable by denesting it, as there can
only be one ISIS daemon instance in FRR.
|
|
t1616-isis
* 'T1316_october' of https://github.com/sever-sever/vyos-1x:
isis: T1316: October steps
|
|
|
|
We had two places were the is_ip, is_ipv4 and is_ipv6 helpers had been defined.
All places now have been converged into vyos.template as they are used both
in the Jinja2 templates and also in our scripts.
|
|
|
|
|
|
This commit has to do with the addition of miscellaneous MPLS parameters, as well as miscellaneous LDP parameters. Per c-po, for miscellaneous options and whatnot that do not fit anywhere we will put them into a specific "parameters" node.
I also did some global linux configuration changes here. We make changes to kernel options "net.mpls.ip_ttl_propagate" and "net.mpls.default_ttl" which should allow the behavior of VyOS to have the same as routers from the big vendors.
I added two LDP options for cisco interoperation TLV and for a dual stack preference.
Lastly, I went through and changes some of the help/description fields in the definitions page because I just felt they weren't uniform and the words seemed to not properly explain what they were doing. I also did some code clean up (or tried to...) with comments and whatnot.
|
|
The commit has to do with the addition of targeted LDP neighbors and parameters being added. FRR allows for this functionality and I just wanted to add it.
We have basically 4 options that are added. Enabling targeted LDP functionality, the targeted neighbor, the hello interval of targeted sessions, and the hold time of targeted sessions. Both IPv4 and IPv6 has been coded in.
|
|
Some might want to have an IP address handed out by a DHCP server but not want
a default route to be installed. This can be done using the CLI command:
"set interfaces ethernet eth2 dhcp-options no-default-route"
|
|
|
|
The commit has to do with the addition of session hold time parameter for LDP neighbors. This allows for being able to change said hold time on a static neighbor.
The way that this works is to have it either delegated to a value (15-65535), or to just be default to whatever FRR stipulates or per the other session configuration values.
I opted to remove the "-ipv4-" only because we know it's an IPv4 session that one has to create first. I figure it's redundant to add it there so I removed it.
|
|
The commit has to do with the addition of TTL security for LDP neighbors. The code was 90% done by Viascheslav. I modified it a little bit to get it to properly work.
We added more parameters to the neighbors dynamic loop. Once this is merged then we should be able to add more for the dynamic neighbor statements.
The way that this works is to have either TTL disabled, or to add the amount of hops accepted for the neighbor.
|
|
* 'wifi-wpa3' of github.com:c-po/vyos-1x:
wireless: T3042: move wifi-regulatory-domain into individual interface definition
wireless: T2653: reset wireless priority to crux state
wireless: T3034: add WPA3 support
wireless: T3043: rename "wpa mode both" to "wpa+wpa2"
ifconfig: T2985: fix wireless-bridge creation
|
|
definition
|
|
mpls-conf: T915: Separate IPv4 and IPv6 hello timers, add IPv6 timers
|
