| Age | Commit message (Collapse) | Author |
|---|
|
|
|
nat: T538: Add static NAT one-to-one
|
|
Remove `default_action` from template "nftables-policy" as XML
policy route does not use it
Set default action 'accept' for policy route, as default action
'drop' must be used only for firewall and not related to the
policy route
|
|
|
|
nat66: T4631: Add port and protocol to nat66 conf
|
|
|
|
|
|
Ability to configure src/dst/translation port and protocol for
SNAT and DNAT IPv6
|
|
From the doc miniupnpd
IP/mask format must be nnn.nnn.nnn.nnn/nn
Comment out invalid option "anchor"
|
|
Ability to set static NAT (one-to-one) in one rule
set nat static rule 10 destination address '203.0.113.0/24'
set nat static rule 10 inbound-interface 'eth0'
set nat static rule 10 translation address '192.0.2.0/24'
It will be enough for PREROUTING and POSTROUTING rules
Use a separate table 'vyos_static_nat' as SRC/DST rules and
STATIC rules can have the same rule number
|
|
|
|
set vpn openconnect network-settings split-dns <domain>
|
|
|
|
Fix template for configuration DMVPN IKE profile
dead-peer-detection delay and dead-peer-detecion timeout options
|
|
|
|
* https://github.com/Cheeze-It/vyos-1x:
bgp: T4257: Changing BGP "local-as" to "system-as"
|
|
|
|
nat66: T4586: Add SNAT destination prefix and DNAT address
|
|
T4480: webproxy: Add safe-ports and ssl-safe-ports for acl squid config
|
|
Ability to configure SNAT destination prefix and
DNAT source address
Add option "!" - not address/prefix for NAT66
|
|
|
|
bgp: T4257: Changing BGP "local-as" to "system-as"
This change is to change the global BGP name for the node "local-as" to "system-as"
This is needed so that there's less ambiguity with the local-as feature per neighbor.
bgp: T4257: Changing BGP "local-as" to "system-as"
bgp: T4257: Changing BGP "local-as" to "system-as"
This change is to change the global BGP name for the node "local-as" to "system-as"
This is needed so that there's less ambiguity with the local-as feature per neighbor.
|
|
hosts/networks that should be ignored.
|
|
|
|
T4550: router-advert: Add deprecate-prefix & decrement-lifetimes options
|
|
|
|
DeprecatePrefix and DecrementLifetimes options in radvd is useful in a DHCPv6-PD environment to accommodate prefix changes from ISP's delegating router. Though there is currently no integration between the DHCP PD client (wide-dhcpv6-client) and radvd, it could be a good start point to have the 2 options configurable by the user.
https://phabricator.vyos.net/T4550
- deprecate-prefix: Upon shutdown, deprecate the prefix. This is useful
in a DHCPv6 PD environment: When ISP re-assigns a new prefix,
deprecate the old prefix that was advertised.
- decrement-lifetimes: Decrement the values of the preferred and valid
lifetimes for the prefix over time. This is also useful in a DHCPv6
PD environment to keep the advertised prefix's lifetimes in sync with
the prefix from delegating router.
|
|
|
|
Fix conflicts
|
|
Fix for IPv6 netflow_plugin name
When we use IPv6 uacctd.conf doesnt expect coluns in the plugin
name. Replace dots and colons to dash.
|
|
As we have specific configuration for each plugin:
set service monitoring telegraf xxx
- azure-data-explorer
- prometheus-client
- splunk
We should to move configuration that related to influxdb under
influxdb node
Replace:
set service monitoring telegraf
- authentication xxx
- bucket xxx
- port xxx
- url
To:
set service monitoring telegraf influxdb xxx
|
|
After discussion with @zsdc this was decided the better long term fix
* Removes hourly logrotate cron in favour of systemd timer override
|
|
|
|
dns: T4509: Add dns64-prefix option
|
|
rfc6147: DNS Extensions for Network Address Translation
from IPv6 Clients to IPv4 Servers
set service dns forwarding dns64-prefix 2001:db8:aabb::/96
|
|
When clients only use DHCP for interface addressing we can not bind NTPd to
an address - as it will fail if the address changes. This commit adds support
to bind ntpd to a given interface in addition to a given address.
set system ntp interface <name>
|
|
Add rate-limit options: attribute, muptiplier and vendor
set service ipoe-server auth radius rate-limit attribute 'Mikrotik-Rate-Limit'
set service ipoe-server auth radius rate-limit enable
set service ipoe-server auth radius rate-limit multiplier '0.001'
set service ipoe-server auth radius rate-limit vendor 'Miktorik'
|
|
set service router-advert interface eth0 name-server-lifetime <value>
|
|
Commit a2ab95ff68b ("pppoe: T4384: replace default-route CLI option with common
CLI nodes already present for DHCP") had an issue as the PPPoE interface options
and also DHCP interface options did not honor the no-default-route option.
This has been fixed.
|
|
|
|
* Refactor nftables clean-up code
* Adds policy route test for using firewall groups
|
|
|
|
|
|
* 'sstp_port' of https://github.com/goodNETnick/vyos-1x:
sstp: T4444. Port number changing support
|
|
firewall: T970: Add firewall group domain-group
|
|
for ipv4
|
|
OWAMP is a command line client application and a policy daemon used
to determine one way latencies between hosts.
OWAMP session control uses traditional client-server communication
between a control-client and a server,
TWAMP (two-way active measurement protocol)
Add configuration and operation modes
set service sla owamp-server
set service sla twamp-server
run force owping 192.0.2.120
run force twping 192.0.2.190
|
|
|
|
prefix-len on both matches. Also change help properties of route-source node.
|
|
|
