| Age | Commit message (Collapse) | Author |
|---|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
(Capitalization fixes, more consice wording etc.)
|
|
This commit has a dependecy on https://github.com/FRRouting/frr/issues/8403,
thus support will be "commented out" by default.
|
|
|
|
|
|
The previously used regex allowed an address value of "dhcpfoo" which is invalid
and will raise an OSError. Harden the regex that it explicitly must be dhcp or
dhcpv6.
|
|
|
|
In this commit we add more address families within
BGP. This should bring VyOS the ability to enable
the rest of the capabilities within FRR.
Co-authored-by: Cheeze_It <none@none.com>
|
|
set vrf name red protocols bgp address-family l2vpn-evpn advertise ipv4 unicast
|
|
After commit 73557d68 ("bgp: T1711: remove ASN tagNode and move to 'local-as'")
when the BGP tag node was removed there is no need anymore for a script based
completion helper, we can rather rely on the build in "path" variant.
|
|
|
|
|
|
Port over the regex used in the old node.def code-base and make this limitation
also live on the new CLI interface.
|
|
|
|
|
|
Commit 548d9057e3e (vrf: T3344: move dynamic routing protocols under "vrf name
<name> protocols") temporary removed the possibility to specify the VNI for a
given VRF to to changing of the CLI configuration nodes.
As VNI is set inside zebra, we can re-use the now widely deployed frr python
library to configure and change the configuration without any interference to
other FRR daemons.
|
|
Sometimes a modem might give a local IP before it retrieves a WAN IP.
This can be an issue with failover routes,
since the default route will get overridden.
|
|
Every time when set configuration bgp, you need set AS number. There is very
less benefit in this system so the AS number is moved from a tagNode level down
to a leafNode with the name "local-as", same as on the neighbor or peer-group
level.
This changes the CLI configuration from:
set protocols bgp 100 neighbor 10.10.1.2 remote-as 200
to
set protocols bgp local-as 100
set protocols bgp neighbor 10.10.1.2 remote-as 200
|
|
As we and FRR do not support multiple FRR process instances, there is no need
to make this configurable for a user. We rather rely on a solid default "VyOS".
|
|
VRF support can be tested using:
set vrf name red table 1000
set vrf name red protocols isis domain FOOO
set vrf name red protocols isis net 49.0001.1921.6800.1002.00
set vrf name red protocols isis interface eth1
|
|
|
|
VyOS 1.2 (crux) rejected prefixes other then of site /64.
[ interfaces ethernet eth0 ipv6 address eui64 2006:ab00:abe1::2/127 ]
Error: Prefix lenght is 127. It must be 64.
Same should be done on VyOS 1.3 and newer
|
|
|
|
As the amount of include files now has reached a certain amount, it is getting
more and more crowsded, thuse introducing "per topic" subdirectories on the
filesystem to keep a clean structure makes sense.
|
|
As the amount of include files now has reached a certain amount, it is getting
more and more crowsded, thuse introducing "per topic" subdirectories on the
filesystem to keep a clean structure makes sense.
|
|
As the amount of include files now has reached a certain amount, it is getting
more and more crowsded, thuse introducing "per topic" subdirectories on the
filesystem to keep a clean structure makes sense.
|
|
As the amount of include files now has reached a certain amount, it is getting
more and more crowsded, thuse introducing "per topic" subdirectories on the
filesystem to keep a clean structure makes sense.
|
|
conf-mode: T2425: Add XML for policy-lists
|
|
When including XML files they all contained a comment from where the snipped
had actually been included from. The comment had been "included start" and
"included end" instead of "include start" and "include end".
This commit corrects the glitch.
|
|
|
|
The following VyOS CLI config
vrf red {
bgp 100 {
neighbor 1.1.1.1 {
peer-group foo
}
peer-group foo {
passive
password bar
remote-as 200
}
}
}
Will generaste the FRR configuration:
!
router bgp 100 vrf red
no bgp ebgp-requires-policy
no bgp network import-check
neighbor foo peer-group
neighbor foo remote-as 200
neighbor foo password bar
neighbor foo passive
neighbor 1.1.1.1 peer-group foo
!
|
|
As the amount of include files now has reached a certain amount, this also
introduces "per topic" subdirectories on the filesystem to keep a clean
structure.
This commit is related to the change in the OSPF structure done in 952c52ef01
("vrf: ospf: T2271: re-arrange xml include building blocks").
|
|
|
|
|
|
In order to fully re-use the XML based OSPF CLI definition for per-VRF routing,
the file structure needs to be reorganized and the common OSPF definition is
moved to its dedicated ospf-common-config.xml.i file, which can then be fully
re-included at the VRF level.
As the amount of include files now has reached a certain amount, this also
introduces "per topic" subdirectories on the filesystem to keep a clean
structure.
|
|
set protocols bgp 65010 address-family l2vpn-evpn vni 100 route-target both 516:10516
set protocols bgp 65010 address-family l2vpn-evpn vni 100 rd 192.168.0.1:514
Todo: add verify() step to check if at least one evpn enabled BGP neighbor
exits, else FRR will error out with: This command is only supported under EVPN VRF
|
|
|
|
* set protocols bgp ASN address-family ipv4-unicast maximum-paths
* set protocols bgp ASN address-family ipv4-unicast maximum-paths-ibgp
* set protocols bgp ASN address-family ipv6-unicast maximum-paths
* set protocols bgp ASN address-family ipv6-unicast maximum-paths-ibgp
|
|
VyOS 1.2 had a default ttl of 16 hardcoded to the node.def file [1], so until
this is handled via a migration script we have to obey that particular
setting.
[1]: https://github.com/vyos/vyatta-cfg-system/blob/crux/templates/interfaces/vxlan/node.def#L23
|
|
|
|
dhcp: T3300: add DHCP default route distance
|
|
|
