| Age | Commit message (Collapse) | Author |
|---|
|
In order to fully re-use the XML based OSPF CLI definition for per-VRF routing,
the file structure needs to be reorganized and the common OSPF definition is
moved to its dedicated ospf-common-config.xml.i file, which can then be fully
re-included at the VRF level.
As the amount of include files now has reached a certain amount, this also
introduces "per topic" subdirectories on the filesystem to keep a clean
structure.
|
|
set protocols bgp 65010 address-family l2vpn-evpn vni 100 route-target both 516:10516
set protocols bgp 65010 address-family l2vpn-evpn vni 100 rd 192.168.0.1:514
Todo: add verify() step to check if at least one evpn enabled BGP neighbor
exits, else FRR will error out with: This command is only supported under EVPN VRF
|
|
|
|
* set protocols bgp ASN address-family ipv4-unicast maximum-paths
* set protocols bgp ASN address-family ipv4-unicast maximum-paths-ibgp
* set protocols bgp ASN address-family ipv6-unicast maximum-paths
* set protocols bgp ASN address-family ipv6-unicast maximum-paths-ibgp
|
|
VyOS 1.2 had a default ttl of 16 hardcoded to the node.def file [1], so until
this is handled via a migration script we have to obey that particular
setting.
[1]: https://github.com/vyos/vyatta-cfg-system/blob/crux/templates/interfaces/vxlan/node.def#L23
|
|
|
|
dhcp: T3300: add DHCP default route distance
|
|
|
|
|
|
Streamline the CLI configuration where we try to use remote on other interfaces
like vxlan, geneve.
|
|
Streamline the CLI configuration where we try to use source-address when
creating connections which are especially sourced from a discrete address.
|
|
A VXLAN tunnel may now get a TTL, TOS, Flowlabel option specified. It is also
possible to disable learning of unknown addresses into the forwarding database.
|
|
|
|
As thought in the beginning the dhcp-interface route option can not be
superseeded by the interface option. When a route is installed for a DHCP
interface, that interface is usually a broadcast interface which can not be
used for plain interface-based routes.
The old Vyatta logic was migrated to Python where the current received
next-hop address from the DHCP interface is installed as next-hop address.
|
|
VXLAN will get tos, ttl and flowlabel options thus make individual parameter
settings reusable by splitting tunnel-parameters-ip.xml.i into individual files.
|
|
|
|
bfd: T3310: migrate to get_config_dict() and FRR reload
|
|
|
|
|
|
When moving from Quagga to FRR the BGP address-family was extended by an
invalid peer-group statement. FRR always moved a configured peer-group
from the AFI level down to the neighbor level.
With the migration to FRR reload we must take care about this by ourselves.
|
|
|
|
* protocols bgp 65000 neighbor 192.0.2.1 address-family ipv4-unicast addpath-tx-all
* protocols bgp 65000 neighbor 192.0.2.1 address-family ipv4-unicast addpath-tx-per-as
* protocols bgp 65000 neighbor 2001:db8::1 address-family ipv6-unicast addpath-tx-all
* protocols bgp 65000 neighbor 2001:db8::1 address-family ipv6-unicast addpath-tx-per-as
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
* 't2450-vrf' of github.com:c-po/vyos-1x:
xml: add new common "interface-name" validator
xml: include: accel: add missing file include comments
smoketest: static: improve static route testing
route: static: T2450: provide full protocol support in XML and Python with new CLI
vrf: T2450: provide full protocol support in XML and Python with new CLI
migrator: ospf: T3267: cleanup empty interface "ip" nodes
|
|
|
|
|
|
new CLI
|
|
|
|
Before 94f886ab ("tunnel: T3173: path MTU discov..."), TTL used the default value
of 255, so c7d08654 ("tunnel: T3030: Modify the comm...") used the default value
of 255. Later, due to the introduction of the PMTU option, the default value was
changed to 0. Continuing to use the default value of 255 will cause the smoke test
to fail, Therefore, the new definition of TTL is migrated
|
|
In 8413278c, we left out a parameter in the tunnel
that caused the tunnel smoke test to fail.
Now, let's add it
|
|
tunnel: T3030: Add erspan protocol support
|
|
|
|
Added "set protocols ospf interface eth1 hello-multiplier <n>" CLI command. This
is mutually exclusive to "set protocols ospf interface eth1 dead-interval <n>".
|
|
|
|
package type automatic detection)
|
|
|
|
|
|
interface"
For easier maintenance and operability move the interface specific protocol
setting of OSPF to the OSPF protocol section. This is now also in-line with IS-IS.
This means to migrate:
ethernet eth0 {
vif 202 {
ip {
ospf {
authentication {
md5 {
key-id 10 {
md5-key vyosvyos
}
}
}
dead-interval 40
hello-interval 10
priority 1
retransmit-interval 5
transmit-delay 1
}
}
}
}
to
protocols {
ospf {
interface eth0.201 {
authentication {
md5 {
key-id 10 {
md5-key vyosvyos
}
}
}
dead-interval 40
hello-interval 10
priority 1
retransmit-interval 5
transmit-delay 1
}
}
|
|
dhcpv6: T3240: support per-interface client DUIDs
|
