| Age | Commit message (Collapse) | Author |
|---|
|
Enable PPPoE control-plane integration with VPP, add configurable
option:
- set service pppoe-server interface eth1 vpp-cp
```
interface=eth1,vpp-cp=true
```
|
|
T7678: Move "vpp settings host-resources" to "system option resource-limits"
|
|
|
|
kea: T6211: add VRF support for KEA dhcp server
|
|
haproxy: T7715: Add rule matching on subdomains
|
|
|
|
|
|
|
|
current configuration
|
|
|
|
It will be configured in section "system option host-resources"
|
|
|
|
T7697: Merge vyos-vpp repo into vyos-1x
|
|
vxlan: T7468: add VLAN-to-VNI mapping description
|
|
|
|
|
|
Added ability for user-defined MAC address for dummy interfaces.
|
|
* VPP: T7175
Added conf mode CLI for VPP sflow plugin and updated VPP template to include plugin.
* VPP: T7175: Conf mode CLI and startup template.
* T7175: VPP fix sFlow verify use vpp enstead of enable_vpp
* T7175: VPP add sFlow smoketest
* T7175: VPP remove unused config_changed variable
---------
Co-authored-by: Viacheslav <v.gletenko@vyos.io>
|
|
Multiple styles were used - streamline this to make it look more professional.
|
|
|
|
In case when there is no local/remote prefix configured in a tunnel settings,
a protocol configured for such tunnel is ignored.
The correct way to generate the configuration is to set the prefix
to `dynamic` if it was not set. The correct config for the described case is:
```
local_ts = dynamic[gre/]
remote_ts = dynamic[gre/]
```
|
|
|
|
|
|
* T7658: Increase max-map-count interval and default value to linux default
Also input a warning instead of ConfigError in case of "host-resources max-map-count" didn't pass the verification
* T7656: Clarify warning message for max-map-count option verification
|
|
ipsec: T7504: Added IKEv2 retransmission options
|
|
Added IKEv2 retransmission options (base, tries, timeout).
|
|
T7595: Support PROXY protocol for haproxy
|
|
|
|
|
|
Some systems have default page-size 4K and it may cause an error
|
|
|
|
* T7424: Refactor and extend resource usage verification on commit for VPP CLI
T7424: Fix ruff errors
* T7424: Implement check for smoke tests runtime; reduce resource requirements for test environments
T7424: Fix errors in calculating the skipped and reserved CPU cores; Adjust default main heap size value.
* T7424: Refactor the CPU checks logic; Add total CPU usage check
T7424: Fix CPU reserve and skip cores calculations; Add total CPU usage check
T7424: Refactor smoketests to reflect new logic
* T7424: Refactor the CPU and memory checks logic
---------
Co-authored-by: oniko94 <onikolaiev94@outlook.com>
|
|
|
|
firewall: T6951: Add a configuration command for ethertypes that bridge firewalls should always accept
|
|
firewalls should always accept
|
|
journald
|
|
T7432: RPKI VRF Support
|
|
conntrack: T7208: nf_conntrack_buckets defaults and behavior
|
|
Previously, we used a lower limit of 1 and a default value of 32768 for the
nf_conntrack_buckets (conntrack hash-size) sysctl option. However, the Linux
kernel enforces an internal minimum of 1024. A configuration migrator will now
adjust the lower limit to 1024 if necessary.
The former default value of 32768 was passed as a kernel module option, which
only took effect after the second system reboot. This was due to the option being
rendered but not applied during the first boot. This behavior has been changed so
that the value is now configurable at runtime and takes effect immediately.
Additionally, since VyOS 1.4 increased the hardware requirements to 4GB of RAM,
we now align the default value of nf_conntrack_buckets with the kernel's
default for systems with more than 1GB of RAM to 65536 entries. Previously, we
only supported half that amount.
|
|
|
|
Allow accepting invalid packets for ethernet types `8021q` and `8021ad`
in addition to ARP and UDP types so that stateful bridge firewall works
for VLAN-aware bridges in addition to regular bridges.
|
|
T6013: Add support for AuthorizedPrincipalsFile to trusted_user_ca_key
|
|
* zebra: T7349: Added importing routes from non to the kernel routing table
Added importing routes from non to the kernel routing table.
---------
Co-authored-by: Christian Breunig <christian@breunig.cc>
|
|
The current implementation for SSH CA based authentication uses "set service
ssh trusted-user-ca-key ca-certificate <foo>" to define an X.509 certificate
from "set pki ca <foo> ..." - fun fact, native OpenSSH does not support X.509
certificates and only runs with OpenSSH ssh-keygen generated RSA or EC keys.
This commit changes the bahavior to support antive certificates generated using
ssh-keygen and loaded to our PKI tree. As the previous implementation
did not work at all, no migrations cript is used.
|
|
We already support using per-user SSH public keys for system authentication.
Instead of introducing a new CLI path to configure per-user principal names,
we should continue using the existing CLI location and store the principal
names alongside the corresponding SSH public keys.
set system login user <name> principal <principal>
The certificate used for SSH authentication contains an embedded principal
name, which is defined under this CLI node. Only users with matching principal
names are permitted to log in.
|
|
Thisc omplements commit e7cab89f9f81 ("T6013: Add support for configuring
TrustedUserCAKeys in SSH service with local and remote CA keys"). It introduces
a new CLI node per user to support defining the authorized principals used by
any given PKI certificate. It is now possible to associate SSH login users with
their respective principals.
Authored-by: Takeru Hayasaka <hayatake396@gmail.com>
|
|
|
|
accel-ppp: T7471: Changed CoA port completion help to standard template
|
|
Bridge: T7430: Add BPDU Guard and Root Guard support
|
|
Changed CoA port completion help to standard template.
|
