Age | Commit message (Collapse) | Author |
|
syslog: T2778: T2769: refactoring and VRF support
|
|
Add RADIUS accounting-interim-interval option for PPPoE/IPoE/SSTP
servers.
Specifies interval in seconds to send accounting information
(may be overridden by radius Acct-Interim-Interval attribute)
set service pppoe-server authentication radius accounting-interim-interval '60'
|
|
Allow syslog messages to be sent through a VRF (e.g. management).
|
|
|
|
|
|
dns: T5144: Improve dynamic DNS validations and completions
|
|
* Re-use XML building blocks when poossible
* Use XML constraints when possible (password)
* Capitalize protocols (HTTP) in <help> strings
|
|
|
|
|
|
|
|
|
|
|
|
Remove superfluous quotes on resource types.
|
|
T5171: Use XML for loadbalancing wan instead of old templates
|
|
Use XML and python3 for 'load-balancing wan'
Use Jinja2 templates instead of old vyatta-wanloadbalance.pl to
generate configuration '/run/load-balance/wlb.conf' wich used by
/opt/vyatta/sbin/wan_lb
|
|
Ability to match 'source-protocol' for the route-map filters
set policy route-map foo rule 10 action 'permit'
set policy route-map foo rule 10 match protocol 'bgp'
|
|
|
|
|
|
This reverts commit bfe57cf80f4c71236f0885408d704a69575f0b30.
|
|
T1237: Failover route add policy for targets checking
|
|
|
|
Add policy (any-available|all-available) for target checking for failover route
set protocols failover route 192.0.2.55/32 next-hop 192.168.122.1 check policy 'any-available'
set protocols failover route 192.0.2.55/32 next-hop 192.168.122.1 check target '192.168.122.1'
set protocols failover route 192.0.2.55/32 next-hop 192.168.122.1 check target '192.168.122.11'
It depends if we need that all targets must be alive on just one target.
|
|
Apply validations and completions to dynamic DNS protocols supported.
This also opens up additional protocols supported by ddclient 3.10.
Additional details:
- Validation and constraint have been added for interface names as well.
- While at it, the help texts got some copyedit and rewording.
|
|
|
|
T5150: implementation of new Kernel/Zebra route-map support
|
|
The (v)bash completion helpers trigger on the "txt" keyword for the valueHelp
strings when asking for the tab completion helper.
Replace text -> txt
|
|
|
|
|
|
|
|
It is possible to install a route-map which filters the routes between routing
daemons and the OS kernel (zebra)
As of now this can be done by e.g.
* set protocols ospf route-map foo
* set protocols ospfv3 route-map foo
* set protocols bgp route-map foo
Which in turn will install the following lines into FRR
* ip protocol ospf route-map foo
* ipv6 protocol ospf6 route-map foo
* ip protocol bgp route-map foo
The current state of the VyOS CLI is incomplete as there is no way to:
* Install a filter for BGP IPv6 routes
* Install a filter for static routes
* Install a filter for connected routes
Thus the CLI should be redesigned to close match what FRR does for both the
default and any other VRF
* set system ip protocol ospf route-map foo
* set system ipv6 protocol ospfv3 route-map foo
* set system ip protocol bgp route-map foo
* set system ipv6 protocol bgp route-map foo
The configuration can be migrated accordingly. This commit does not come with
the migrator, it will be comitted later.
|
|
dns: T5143: Apply constraint for domain name in DNS forwarding
|
|
|
|
T5081: ISIS and OSPF syncronization with IGP-LDP sync
|
|
Initially the option 'rate-limit' was implemented with the
wrong place in the CLI:
set vpn pptp remote-access authentication rate-limit <xxx>
Expected under 'radius' section:
set vpn pptp remote-access authentication radius rate-limit <xxx>
Configuration for 'rate-limit' (Jinja2 template) never worked for
pptp, fix it.
|
|
There is only one target for checking ICMP/ARP
Extend it for checking multiple targets
set protocols failover route 192.0.2.55/32 next-hop 192.168.122.1 check target '203.0.113.1'
set protocols failover route 192.0.2.55/32 next-hop 192.168.122.1 check target '203.0.113.11'
The route will be installed only if all targets are 'alive'
|
|
|
|
maxsyslogins
maximum number of all logins on system; user is not
allowed to log-in if total number of all user logins is
greater than specified number (this limit does not apply
to user with uid=0)
set system login max-login-session 2
|
|
This will prevent arbitrary strings from being entered as domain names.
Additionally, reuse the fqdn validator instead of a custom regex.
|
|
IKE lifetime should starting from 0 for disabling rekeying
|
|
Container networks now can be bound to a specific VRF instance.
set vrf name <foo> table <xxx>
set container network <name> vrf <foo>
|
|
Remove redundant XML CLI node definitions for the common description node by
referencing the common building block.
|
|
We now support assigning discrete IPv6 addresses to a container.
|
|
|
|
|
|
|
|
|
|
include at least one wildcarded interface
|
|
|
|
|
|
This would allow using custom ports in name server operating on non-
default port for forwarding zones.
This is a follow-up to T5113 for sake of completeness and having
consistent treatment of all name servers configured in PowerDNS recursor.
Additionally, migrate `service dns forwarding domain example.com server`
to `service dns forwarding domain foo3.com name-server` for consistency
and reusability.
|