| Age | Commit message (Collapse) | Author |
|---|
|
syslog: T7270: fix typos in rsyslog.conf
|
|
If a router has not formed an LDP neighbor adjacency yet, it
answers all received LDP Hello packets from non-neighbors with
new Hello packets.
This leads to flooding LDP packets to all routers for each LDP
incoming packet.
Add configuration option to disable this behavior
```
set protocols mpls ldp interface eth0 disable-establish-hello
```
|
|
|
|
|
|
|
|
|
|
* bgp: T7157: Allow using route-maps for VRF route leaking in BGP
Added the possibility of using route-map in route leaking.
* Improve the constraint error message
---------
Co-authored-by: Daniil Baturin <daniil@baturin.org>
|
|
|
|
|
|
T7050 revealed an issue in the CI system where VyOS CLI was rendering a
configuration for wide-dhcpv6-client that was not working due to a missing
patch of the wide-dhcpv6-client source code.
This can be prevented by checking the daemon logs after startup for any config
linguistic (Yacc/Bison) issues.
|
|
|
|
Changed priority for VPP interfaces: all VPP interfaces must be configured after Ethernet interfaces
|
|
|
|
|
|
Otherwise rsyslog will report an error:
omfwd: could not get addrinfo for hostname '[2001:db8::2]':'514': System error
|
|
New CLI command
set system syslog marker disable
|
|
T7200: Reduce memory size usage for vpp smoke tests
|
|
T6948: Keep DHCP server leases in sync with hostd records
|
|
T7118: Added the ability to redistribute NHRP routes to other protocols
|
|
policy: T7158: Added match source-vrf to route-map
|
|
* wlb: T7196: Migrate interface wildcards to nftables format
* wlb: T7196: Fix exclude/interface verify check
* wlb: T7196: Extra sanity check on ipv4 address function
|
|
Added match source-vrf to route-map
|
|
Added the ability to redistribute NHRP routes to:
OSPF
BGP
Babel
RIP
IS-IS
|
|
add more memory validation
|
|
Allow to configure VPP loopback interface as BVI interface
In the VPP a bridge-domain is the L2 bridge and does not have
its own interface
Loopback is required if we want to ping from/to the bridge.
```
set vpp interfaces bridge br10 member interface lo23 bvi
```
|
|
lldp: T7165: add support to enable only rx/tx on specific interfaces
|
|
LLDP is a stateless protocol which does not necessitate sending to receive
advertisements. There are multiple scenarios such as provider peering links in
which it is advantageous to receive LLDP but not disclose internal information
to the provider.
Add new CLI command:
* set service lldp interface <name> mode [disable|rx-tx|rx|tx]
The default is unchanged and will be rx-tx.
Furthermore if an interface has an explicit LLDP disable configured under
"set service lldp interface <name> disable" this will be migrated to
"set service lldp interface <name> mode disable"
|
|
T7190: Add haproxy default timeout options configurable
|
|
bond: T7191: fix error message when member interface is used multiple times
|
|
Skip the bonding test as CI stucks on it
But this test works fine in the local VM
|
|
Add the ability to configurate default timeout and frontend
client timeout
```
set load-balancing haproxy service web timeout client '600'
set load-balancing haproxy timeout check '4'
set load-balancing haproxy timeout client '600'
set load-balancing haproxy timeout connect '12'
set load-balancing haproxy timeout server '120'
```
|
|
When configuring
set interfaces bridge br10 member interface eth1
set interfaces bridge br20 member interface eth1
commit
Checking the interface assignment afterwards shows
242: br20: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000
link/ether 62:34:3a:8a:fe:49 brd ff:ff:ff:ff:ff:ff
[edit]
3: eth1: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel master br20 state UP mode DEFAULT group default qlen 1000
link/ether 00:50:56:b3:cd:ba brd ff:ff:ff:ff:ff:ff
altname enp0s19
altname ens19
The later addition wins and the CLI reports eth1 is assigned to br20 "master
br20". A member interface can not be used multiple times.
|
|
Sharing the same physical interface among multiple bond interfaces causes
information to be lost within the error message
set interfaces bonding bond10 member interface eth1
set interfaces bonding bond10 member interface eth2
set interfaces bonding bond20 member interface eth1
set interfaces bonding bond20 member interface eth2
commit
Results in:
[ interfaces bonding bond10 ]
Can not add interface "eth1" to bond, it is already a member of bond
"b"!
[[interfaces bonding bond10]] failed
[ interfaces bonding bond20 ]
Can not add interface "eth1" to bond, it is already a member of bond
"b"!
It should infact output the full name of the bond interface.
|
|
|
|
Add required IP addresses on the interface eth1 which is a source
of a tunnel
|
|
T7077: Verify VPP memory default-hugepage-size
T7079: Verify VPP memory main-heap-page-size
T7080: Verify VPP statseg page-size
get available hugepage sizes
align memory main-heap-size by page size
validate host_resources max_map_count
|
|
|
|
T5810: Add support for RPKI source ip
|
|
firewall: T7177: Update interface-name constraint to allow "pod-" interface names
|
|
|
|
support pod interfaces from containers
|
|
|
|
bgp: T7163: add CLI route-map and metric support for "redistribute table"
|
|
wlb: T4470: Migrate WAN Load Balancer to XML/Python
|
|
|
|
The test `test_dhcp_hostsd_lease_sync` validates
DHCP server leases in sync with hostd records.
Since the DHCP server running in smoketest environment
might not have actual clients to lease IP addresses,
we simulate the lease creation and deletion using kea
helper functions (`kea_add_lease` and `kea_delete_lease`).
|
|
|
|
|
|
|
|
* set protocols bgp address-family <ipv4-unicast|ipv6-unicast> redistribute
table <n> [metric <n>] [route-map <name>]
|
