| Age | Commit message (Collapse) | Author |
|---|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
equipment
According to the consensus, the specific behavior of a VLAN aware bridge should conform
to the behavior of professional equipment. This commit makes a significant change to the
behavior of VLAN aware bridge, and has the following behaviors:
1. Disable `vif 1` configuration
2. When the VLAN aware bridge is enabled, the parent interface is always VLAN 1
3. When `native-vlan` is not configured, the default behavior of the device is `native-vlan 1`
4. The VLAN ids forwarded by the bridge are determined by `vif`
5. It has an `enable-vlan` node to enable VLAN awareness
6. VLAN configuration is allowed only when VLAN aware bridge is activated
|
|
In the implementation of T3042, it will cause two problems:
1. Even if VLAN awareness is not enabled, the VLAN settings of the
vlan filter will be modified. When the bridge member has a WLAN interface,
the error is exposed, so repair it here. You should not modify the
related settings when the VLAN awareness mode is not enabled
2. Even if VLAN awareness is not enabled, the VLAN settings of the
vlan filter will be modified. When the bridge member has a WLAN interface,
due to special settings, the bridge mode cannot be entered and the settings
cannot be completed directly. Therefore, the WLAN interface should be rejected
Enter the bridge with VLAN awareness
|
|
|
|
Renamed using snippet below:
----------------------------
for file in $(find . -name "*.py")
do
sed -i "s/vyos_dict_search/dict_search/" $file
done
|
|
The current implementation for bridge based interfaces has an issue which is
caused by priority inheritance. We always assumed that the bridge interface will
be created last, but this may not be true in all cases, where some interfaces
will be created "on demand" - e.g. OpenVPN or late (VXLAN, GENEVE).
As we already have a bunch of verify steps in place we should not see a bridge
interface leak to the underlaying infrastructure code. This means, whenever an
interface will be member of a bridge, and the bridge does yet not exist, we will
create it in advance in the interface context, as the bridge code will be run
in the same commit but maybe sooner or later.
This will also be the solution for T2924.
|
|
|
|
Using an MTU less then the required 1280 bytes (as per RFC) on an interface
where IPv6 is not explicitly disabled by:
- set interfaces ethernet eth1 ipv6 address no-default-link-local
- not having any other IPv6 address configured
Will now trigger a commit error via verify() instead of raising
FileNotFoundError!
|
|
As we already check that a bond/bridge member interface is not a member of any
other bridge or bond, the check must be extended. We also need to ensure that
the bond member interface is not used as a source-interface to pppoe, macsec,
tunnel, pseudo-ethernet, vxlan interfaces.
|
|
|
|
|
|
Further reduce the boiler-plate code to determine interface tag node or not.
It can be passed into get_interface_dict() if explicitly required - else it
is taken from the environment.
|
|
This can be used to see if a tagNode has been changed. It will return a list
of changed nodes.
|
|
The current VyOS CLI parser code written in Python contains a ton of duplicates
which I can also hold myself accountable for - or maybe mainly me - depends on
the angle of judge.
While providing a new update() method in vyos.ifconfig.interfaces() this is
extended for bridge interfaces in the derived bridge class.
Signed-off-by: Christian Poessinger <christian@poessinger.com>
|
|
airbag :T2088: make airbag explicit
|
|
airbag must now be explicitly installed.
the patch also allow to fully disables the installation of the logging
code at setup (and not just installing and doing nothing)
|
|
Some ISPs (e.g. Comcast) only delegate a /64 by default. You have to explicitly
"ask" for a bigger (e.g. /60) prefix. This commit adds a CLI node to request
a specific prefix length in the range 32 - 64.
dhcpv6-options {
prefix-delegation {
length 60
}
}
|
|
Rename the CLI nodes for prefix delegation from "dhcpv6-options delegate
<interface>" to "dhcpv6-options prefix-delegation interface <interface>".
The change is required to add the possibility to request for specific prefix
sized via the CLI. That option was not possible with the old configuration
tree.
|
|
Add support for prefix delegation when receiving the prefix via ethernet,
bridge, bond, wireless.
|
|
This is to remove the amount of duplicated entries in dictionaries. It's one
more part to move to a unified interface management.
|
|
To make SLAAC and DHCPv6 work when forwarding=1, accept_ra must be 2
(default for accept_ra is 1).
|
|
We've already verified that all member interfaces don't have any
addresses configured, so it should be safe to simply call 'ip addr flush' on
them to flush the remaining addresses (e.g. IPv6 link-local)
|
|
|
|
- use is_member function instead of checking config directly
- rearrange to join 2 for loops into one
- make error output more user friendly
- replace .format with f-strings
- split into lines less than ~80 characters long
|
|
Was previously moved out of this script.
|
|
Any remaining addresses of an interface (e.g. IPv6 link-local) will be flushed
when adding a member.
A direct call to ip is necessary for interfaces not under the Interface class
(e.g. vlan vif*)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Break the code between v4 and v6, remove need for getter/setter
as they are just exposing the underlying dict.
Move FixedDict from tunnel code and expose it to other part so
it can be used to prevent accidental change to the dhcp option if
no default exists already.
|
|
Interfaces enslaved to a bridge are not allowed to be deleted. If an interface
is deleted from the config but it is still enslaved to a bridge will cause a
configuration error on the subsequent boot.
|
|
|
|
Autoconfigure addresses using Prefix Information in Router Advertisements.
|
|
|
|
... to new XML and Python based frontend/backend.
|
|
The Interface get_state/set_state were not clear about
if they edited the admin or operational state.
functions are now using admin_state and oper_state
for clarity.
|
|
|
|
|
|
|
|
os.environ['VYOS_TAGNODE_VALUE']
This has been only a theoretical problem but then the error condition was
triggered - only an error has been printed instead of raising an Exception.
|
|
Provide an XML/Python abstraction to
* ip disable-arp-filter
* ip enable-arp-accept
* ip enable-arp-announce
* ip enable-arp-ignore
The old implementation can co-exist until the last interfaces have been
migrated.
|
