| Age | Commit message (Collapse) | Author |
|---|
|
* T5195: move run, cmd, call, rc_cmd helper to vyos.utils.process
* T5195: use read_file and write_file implementation from vyos.utils.file
Changed code automatically using:
find . -type f -not -path '*/\.*' -exec sed -i 's/^from vyos.util import read_file$/from vyos.utils.file import read_file/g' {} +
find . -type f -not -path '*/\.*' -exec sed -i 's/^from vyos.util import write_file$/from vyos.utils.file import write_file/g' {} +
* T5195: move chmod* helpers to vyos.utils.permission
* T5195: use colon_separated_to_dict from vyos.utils.dict
* T5195: move is_systemd_service_* to vyos.utils.process
* T5195: fix boot issues with missing imports
* T5195: move dict_search_* helpers to vyos.utils.dict
* T5195: move network helpers to vyos.utils.network
* T5195: move commit_* helpers to vyos.utils.commit
* T5195: move user I/O helpers to vyos.utils.io
|
|
In cases with multiple named IP pools, it is required the option 'next'
to be sure that if IP addresses ended in one pool, then they would
begin to be allocated from the next named pool.
For accel-ppp it requires specific order as pool must be defined
before we can use it with the 'next-option'
set service ipoe-server client-ip-pool name first-pool subnet '192.0.2.0/25'
set service ipoe-server client-ip-pool name first-pool next-pool 'second-pool'
set service ipoe-server client-ip-pool name second-pool subnet '203.0.113.0/25'
[ip-pool]
203.0.113.0/25,name=second-pool
192.0.2.0/25,name=first-pool,next=second-pool
|
|
As we don't have global option 'gateway-address' for ipoe-server
we cannot use general configverify.verify_accel_ppp_base_service
Add verify radius setting for configuration mode 'radius'
Radius authentication required at least one RADIUS server
|
|
IPoE-server 'interface ethX vlan xxx' (aka vlan-mon) must not be
used with 'interface ethX client-subnet'
So instead of shared pool accel-ppp uses the same pool for each
dynamically added VLAN
eth1 client-subnet '192.0.2.0/24'
eth1 vlan '2000-2021'
It cause this issue:
eth1.2000 range 192.0.2.0/24 (the first client gets address from 192.0.2.2)
eth2.2001 range 192.0.2.0/24 (the first client gets address from 192.0.2.2)
Only named pools with vlan option must be used.
|
|
In addition to the rewrite to make use of get_config_dict() the CLI is
slightly adjusted as specified in T4703.
* Rename vlan-id and vlan-range to simply vlan
* Rename network-mode to simply mode
* Re-use existing common Jinja2 template for Accel-PPP which are shared
with PPPoE and SSTP server.
* Retrieve default values via defaultValue XML node
|
|
Add rate-limit options: attribute, muptiplier and vendor
set service ipoe-server auth radius rate-limit attribute 'Mikrotik-Rate-Limit'
set service ipoe-server auth radius rate-limit enable
set service ipoe-server auth radius rate-limit multiplier '0.001'
set service ipoe-server auth radius rate-limit vendor 'Miktorik'
|
|
|
|
Add new feature to allow to use named pools
Can be used also with Radius attribute 'Framed-Pool'
set service ipoe-server client-ip-pool name POOL1 gateway-address '192.0.2.1'
set service ipoe-server client-ip-pool name POOL1 subnet '192.0.2.0/24'
|
|
|
|
We had two places were the is_ip, is_ipv4 and is_ipv6 helpers had been defined.
All places now have been converged into vyos.template as they are used both
in the Jinja2 templates and also in our scripts.
|
|
|
|
|
|
Make the port used for RADIUS accounting user configurable. This is now
valid for the following services which are based on Accel-PPP:
* ipoe-server
* pppoe-server
* l2tp
* pptp
* sstp
|
|
|
|
airbag must now be explicitly installed.
the patch also allow to fully disables the installation of the logging
code at setup (and not just installing and doing nothing)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
implementations
|
|
|
