| Age | Commit message (Collapse) | Author |
|---|
|
This is a successor to commit a2ac9fac16e ("vyos.template: T2720: always enable
Jinja2 trim_blocks feature"). It only shifts the whitespaces / indents inside
the keepalived configuration file.
|
|
This option is mandatory and must be user configurable as it needs to match
on both sides.
|
|
|
|
|
|
vyos@vyos# show service dhcp-server
shared-network-name LAN {
subnet 10.0.0.0/24 {
default-router 10.0.0.1
dns-server 194.145.150.1
lease 88
range 0 {
start 10.0.0.100
stop 10.0.0.200
}
static-route 192.168.10.0/24 {
next-hop 10.0.0.2
}
static-route 192.168.20.0/24 {
router 10.0.0.2
}
}
}
|
|
Manually set peer id and use-x509-id are mutually exclusive!
|
|
squid: squidguard: T3810: Fix template for sourcre-group and rule
|
|
|
|
Move the two implementations to get the driver name of a NIC from ethernet.py
and ethtool.py to only ethtool.py.
(cherry picked from commit 07840977834816b69fa3b366817d90f44b5dc7a7)
|
|
In order to alter rpki configuration we must also process the route-map nodes
with/for bgpd.
|
|
Add support for OpenVPN client mode with only the CA certificate of the server
installed.
|
|
|
|
|
|
|
|
|
|
|
|
This commit also extends the smoketest to verify that the exception for this
error is raised.
|
|
|
|
We have "set system name-server <ipv4|ipv6>" to specify a name-server IP
address we wan't to use. We also have "set system name-servers-dhcp <interface>"
which does the same, but the name-server in question is retrieved via DHCP.
Both CLI nodes are combined under "set system name-server <ipv4|ipv6|interface>"
to keep things as they are in real life - we need a name-server.
(cherry picked from commit 2ecf7a9f9cbe9359457bd23b4a0c45f3763123c7)
|
|
Commit 5f1c1ae4 ("bgp: T3798: add support for neighbor local-as <n> replace-as")
added support for a new CLI option when the local-as is changed for a specified
neighbor or peer-group.
There was an error in the CLI / design as the "replace-as" option can only be
used when "no-prepend" is defined. Thus "no-prepend" became a <node> and
the new "replace-as" leafNode is now a child of "no-prepend".
|
|
This patch allows the use of `"` in ssh public-key options which
unlocks the ability to set the `from` option in a way that sshd will
accept to limit what hosts a user can connect from.
|
|
|
|
Keys are not allowed with ipip and sit tunnels
|
|
While migrating to get_config_dict() in commit e8a1c291b1 ("login: radius:
T3192: migrate to get_config_dict()") the user-name was not excluded
from mangling (no_tag_node_value_mangle=True).
This resulted in a username "vyos-user" from CLI to be actually created as
"vyos_user" on the system.
This commit also adds respective Smoketests to prevent this in the future.
|
|
The workaround is no longer required, as the issue was resolved in
get_config_dict() so if it is a <multi/> node, a list is always returned.
|
|
tunnel: T2920: Add checks tun with same source addr and keys
|
|
2 tunnels with the same local-address should has different keys
Check existing tunnels (source-address key) with new tunnel.
|
|
It makes no sense to have a parser for the ethtool values in ethtool.py
and ethernet.py - one instance ios more then enough!
|
|
Only update the RX/TX ring-buffer settings if they are different from the ones
currently programmed to the hardware. There is no need to write the same value
to the hardware again - this could cause traffic disruption on some NICs.
|
|
Not all interface drivers have the ability to change the speed and duplex
settings. Known drivers with this limitation are vmxnet3, virtio_net and
xen_netfront. If this driver is detected, an error will be presented to the
user.
|
|
Ethernet adapters have a discrete set of available speed and duplex settings.
Instead of passing every value down to ethtool and let it decide, we can do
this early in the VyOS verify() function for ethernet interfaces.
|
|
|
|
Check a port availability only if it was changed in current commit.
This should protect from fail-positive errors when other parameters
change for an interface.
|
|
The commit fixes the problem, when port availability check is
triggered even if a port for WireGuard interface is not defined
(randomized port, default behavior).
|
|
|
|
Add new CLI command:
* "set protocols ospf redistribute table <n>"
|
|
Mandatory FRR options for spf-delay-ietf did not get rendered in the Jinja2
template.
|
|
wireguard: T3763: Added check for listening port availability
|
|
`print` was removed or replaced to `ValueError`, where possible.
|
|
Extended CLI command: "set vpn ipsec remote-access connection rw pool" with a
"radius" option.
|
|
Each wireguard interface requires a unique port for in and out
connections. This commit adds the new `vyos.util` function -
`check_port_availability`, and uses it to be sure that a port
that is planned to be used for wireguard interface is truly
available and not used by any other services (not only other
wireguard interfaces).
|
|
|
|
After commit 209ce3d9 ("container: T3769: when container networks are used,
always bridge the networks") IP masquerading (NAT) was disabled. No need to
keep the haipin flag.
|
|
As VyOS is a network operation system with bridging and NATing available from
the VyOS CLI, it makes no sense to let podman do it's own sort of "NAT".
If one really want's to NAT into a container, use the VyOS CLI to do so. If you
wan't to bridge your networks, use the VyOS CLI to do so.
|
|
|
|
Volumes must have both a source and destination path specified. Also the
source path must exist on the current system.
|
|
A call to .items() was missing that triggered the following error:
ValueError: too many values to unpack (expected 2)
|
|
As VyOS CLI is the only truth for dealing with containers we do not need to
query if a container is running, exists or what so ever. We simply always
restart it if something changes and do not rely on the underlaying Linux
status.
If a users does container stuff under the hood - it will be overridden.
|
|
|
|
A container is limited to 256MB memory by default and will always restart on
failure.
|
