| Age | Commit message (Collapse) | Author |
|---|
|
Now both files and directories are supported.
|
|
If the unreachable routes for IPv4 and IPv6 are not deleted, there will be an
error when creating the same VRF again after removal.
Error changing VRF: Command '['sudo', 'ip', '-4', 'route', 'del', 'vrf',
'Blue', 'unreachable', 'default', 'metric', '4278198272']' returned
non-zero exit status 2.
|
|
|
|
This is a low level requirement for supporting l2vpn evpn.
|
|
wireless: T2211: bugfix: vht_oper_chwidth was not set in hostapd config
|
|
openvpn: T2222: set 'multihome' option when local-host is unset
|
|
When any defaults are set, VHT capabilities are automatically assumed
for all WiFi modes which does not match the reality. Therefore we must
leave this undefined by default.
|
|
When operating in certain modes, channel width must be configured for
WiFi interfaces. The hostapd config does this in two separate lines
which must both be configured:
vht_oper_chwidth=(0|1|2|3)
vht_capab+=[VHT160] for 160MHz in one block or
vht_capab+=[VHT160-80PLUS80] for 160MHz as 2x 80MHz in two separate
blocks.
|
|
Commits to
"interfaces wireless wlanX capabilities vht link-adaptation (unsolicited|both)"
always failed.
|
|
If configured with protocol udp and no local-host, openvpn needs
the 'multihome' option to correctly work on all addresses.
|
|
Commit b250b233ec1 ("pppoe: T1318: move Jinja2 templates to data/templates
folder") actually placed the pre-up configuration script into the ip-up
folder.
|
|
As PPPoE interfaces should be part of a VRF it is required that the default
can also be set into the specified VRF. The default way of PPP by setting the
"defaultroute" option does not take a VRF into account. In this case PPP
installs a Kernel route forwarding all default traffic over this interface.
This change installs a static route with metric 1 instead into the routing
table via FRR. This is not the same as a Kernel route in terms of metric 1
compared to 0 but it should do the trick.
|
|
|
|
This makes the actual code which generates the configs much more human
readable.
|
|
|
|
This makes the actual code which generates the configs much more human
readable.
|
|
A ip-pre-up script is better the ip-up as this is done before any addresses
have been added and any traffic flows.
|
|
VRRP: T1820: Added transition-script support for sync-groups
|
|
|
|
|
|
|
|
Commit 6a0c6783d8b2 ("pppoe: migrate alias and vrf script from pre-up to up")
changed the name of the ip-up script template but the template definition has
been forgotten.
This caused:
NameError: name 'config_pppoe_ip_up_tmpl' is not defined
|
|
As the pre-up script is only run once when the interface is brought up but
not when the interface maybe only comes up 20 seconds later due to the remote
site some actions can not be performed as placing the interface e.g. into a VRF
instance.
TODO: also move the backup default route parts to this new script.
|
|
As the pre-up script is only run once when the interface is brought up but
not when the interface maybe only comes up 20 seconds later due to the remote
site some actions can not be performed as placing the interface e.g. into a VRF
instance.
|
|
Commit d2cf287 ("vyos.util: add chown_file and chmod_x_file helpers") added
common helper functions to chown or chmod +x a file. Make use of those helpers.
|
|
Commit d2cf287 ("vyos.util: add chown_file and chmod_x_file helpers") added
common helper functions to chown or chmod +x a file. Make use of those
helpers.
|
|
|
|
|
|
Note: if transition-scripts configured for both vrrp instance and sync group, which are it a member of, both scripts will be executed.
|
|
In old implementation, all notify scripts are configured directly inside a keepalived.conf. This way is not recommended even by keepalived as scripts execution is not tracked and they may be running not in order and killed before the actual work will be finished. We have observed such situations in very rare cases during tests.
New implementation use FIFO pipe, to which keepalived send any state changes. And these notifications are read by a daemon, saved in a queue and processed one by one, which eliminates the situation when the scripts creating inconsistent config or environment.
|
|
By default, the HTTP API will be proxied by any nginx virtual server.
Allow specifying a subset of servers to act as proxy.
|
|
A user reported a PHY that provides two consecutive MAC addresses, this case has
been added as I was not aware of such cards. As we manipulate the MAC address
anyways its safe to take only the first one.
|
|
The list of VRFs to remove has been converted to a dict. The deletion of a VRF
was no longer triggered as the logic still thought it is a list.
|
|
OpenVPN, WIFI, SSTP all had the same boiler plate copied about checking if a
process associated with a pidfile is running or not. This has been migrated to
the common library function vyos.util.process_running().
|
|
|
|
|
|
|
|
|
|
The creation of this directory has been done in the past using vyatta-
wirelessmodem and after it's replacement in vyos-1x the directory has not been
deployed anymore. Thos when rendering the PPPoE configuration the directory will
be created on deemand.
|
|
ifconfig: T2057: Do not set empty hw_id mac
|
|
|
|
|
|
|
|
|
|
set_mac is validating the mac address passed, therefore passing
empty string will cause it to fail. if the hardware id could
not be found then it should not be attempted to be set
|
|
|
|
Autoconfigure addresses using Prefix Information in Router Advertisements.
|
|
|
|
... to new XML and Python based frontend/backend.
|
|
ifconfig: T2057: explicity name state functions
|
