Age | Commit message (Collapse) | Author |
|
that was replaced with Humps in all sciprts
|
|
T5158: Refactoring the commad sh interfaces counters
|
|
For more detailed information it's necessary to add information about drops and error counters.
|
|
T5215: add a built-in ping check for VRRP groups
|
|
|
|
Add RADIUS accounting-interim-interval option for PPTP-server
Specifies interval in seconds to send accounting information
(may be overridden by radius Acct-Interim-Interval attribute)
set vpn pptp remote-access authentication radius accounting-interim-interval '52'
|
|
Add RADIUS accounting-interim-interval option for L2TP-server
Specifies interval in seconds to send accounting information
(may be overridden by radius Acct-Interim-Interval attribute)
set vpn l2tp remote-access authentication radius accounting-interim-interval '120'
|
|
cloud-init: T5190: Added Cloud-init pre-configurator
|
|
T5060: Add disable option for high-availability
|
|
syslog: T2778: T2769: refactoring and VRF support
|
|
|
|
Allow syslog messages to be sent through a VRF (e.g. management).
|
|
|
|
Add 'maintenance mode' (option disable) for high-availability
set high-availability disable
|
|
dns: T5144: Improve dynamic DNS validations and completions
|
|
Use 'vyos-wan-load-balance.service' for load-balancing instead of
old start and stop 'vyatta-wanloadbalance.init' script
|
|
Add 'vyos-wan-load-balance.service' systemd unit for
'loadbalancing wan' instead of old vyatta-wanloadbalance.init script
|
|
|
|
|
|
|
|
Added a new service that starts before Cloud-init, waits for all network
interfaces initialization, and if requested by config, checks which interfaces
can get configuration via DHCP server and creates a corresponding Cloud-init
network configuration.
This protects from two situations:
* when Cloud-init tries to get meta-data via eth0 (default and fallback variant
for any data source which depends on network), but the real network is connected
to another interface
* when Cloud-init starts simultaneously with udev and initializes the first
interface to get meta-data before it is renamed to eth0 by udev
|
|
T5171: Use XML for loadbalancing wan instead of old templates
|
|
|
|
Use XML and python3 for 'load-balancing wan'
Use Jinja2 templates instead of old vyatta-wanloadbalance.pl to
generate configuration '/run/load-balance/wlb.conf' wich used by
/opt/vyatta/sbin/wan_lb
|
|
|
|
Without the change users might get confused as the setting is specified
on the VyOS CLI but never makes it to FRR due to an internal FRR check.
|
|
When we delete vrf vni there is a dictionary
{'only_vrf': 'red', 'new_frr_config': '!\n'}
|
|
conntrack-sync: T4888: rewrite the op mode script in the new format
|
|
Add verify() section to check if l3vni was removed in addition to the BGP
process under any given VRF.
|
|
|
|
|
|
|
|
FastAPI v0.92.0 (starlette v0.24.0) sets default attribute
Request._form; check for value == None instead of existence when
overriding Request class.
|
|
|
|
T1237: Failover route add policy for targets checking
|
|
dns: T5144: Make dns dynamic status output legacy format compatible
|
|
We must only search and replace for "vrf red" or "vrf green" - the regex
used infact matched on all VRFs which is wrong. This would remove all VRF VNI
configurations when only changing a single VRf.
|
|
ipsec: T5042: Rewritten 'show vpn ipsec remote-access' command
|
|
|
|
Add policy (any-available|all-available) for target checking for failover route
set protocols failover route 192.0.2.55/32 next-hop 192.168.122.1 check policy 'any-available'
set protocols failover route 192.0.2.55/32 next-hop 192.168.122.1 check target '192.168.122.1'
set protocols failover route 192.0.2.55/32 next-hop 192.168.122.1 check target '192.168.122.11'
It depends if we need that all targets must be alive on just one target.
|
|
Apply validations and completions to dynamic DNS protocols supported.
This also opens up additional protocols supported by ddclient 3.10.
Additional details:
- Validation and constraint have been added for interface names as well.
- While at it, the help texts got some copyedit and rewording.
|
|
pki: T3642: Fix show command if no CA certs are present
|
|
op-mode: T5159: dhcpv6 incorrect warning message
|
|
The operational command "show dhcpv6 server leases" shows a warning message e
ven if dhcpv6 setting are configured and ipv6 address
got assigned to clients.
|
|
|
|
Adjust the output of dynamic dns status to be compatible with both
legacy and new ddclient cache format. This is necessary because the
legacy format is still used by some of the dyndns2 family of protocols.
This is a follow-up to commit 3f3621b6874354.
|
|
Split script to small functions for flexible output reports.
Improve header for commands.
Each funciton easily can be modified or extended.
Remove splitting command/output via percent symbol.
Remove old commands and directiories like /etc/rc.local, iptables,
brctl, etc.
Remove ethtool operation for subinterfaces.
Extend ethtool debug output.
Add correct nftables command.
|
|
Now 'show vpn ipsec remote-access' shows only IKEv2 Remote access
VPN IPSec connections.
Added option 'summary' that shows a summary table for
these connections.
Added option 'detail' that shows only RA SAs output of 'swanctl -l'
Added options 'username' and 'connection-id' that filters output.
Fixed output 'show vpn ipsec sa detail', the previous was
'show vpn ipsec sa verbose'.
|
|
With commit 0ea3e1420 ("container: T5082: switch to netavark network stack")
moving to a new network stack we should also enable the new DNS plugin provided
by default.
TODO: add CLI nodes to manually disable DNS and/or supply external DNS servers
to the container.
|
|
If the name of the network + the length of the podman- prefix exceeds
the maximum supported length of netavark we get an error:
Error: netavark: get bridge interface: Netlink error: Numerical result out of
range (os error 34)
|