| Age | Commit message (Collapse) | Author |
|---|
|
Introduced in commit 818a75c024e ("ifconfig: T2653: get_mtu() should return
int() for easier comparison") where the variable used in the formatted string
has not been adjusted.
|
|
|
|
|
|
|
|
Using an MTU less then the required 1280 bytes (as per RFC) on an interface
where IPv6 is not explicitly disabled by:
- set interfaces ethernet eth1 ipv6 address no-default-link-local
- not having any other IPv6 address configured
Will now trigger a commit error via verify() instead of raising
FileNotFoundError!
|
|
|
|
Check the hardware if MTU value is supported at all.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
As we already check that a bond/bridge member interface is not a member of any
other bridge or bond, the check must be extended. We also need to ensure that
the bond member interface is not used as a source-interface to pppoe, macsec,
tunnel, pseudo-ethernet, vxlan interfaces.
|
|
|
|
Add verify() step to ensure the macsec source-interface is not already part
of a bridge interface. This should probably also be checked for bond interfaces.
|
|
Base MTU for MACsec is 1468 bytes (encryption headers), but we leave room for
802.1ad and 802.1q VLAN tags, thus the limit is lowered to 1460 bytes to not
make the user juggle with the MTU bytes if he enables VLAN support later on,
which is yet to come.
|
|
A lot of derived classes from Interface implemented their own get_config()
method which more or less was the same everywhere. We also hat different
qualifiers like @staticmethod or @classmethod.
This is now changed to only have the @classmethod in Interface base class which
will return the necessary dictionary keys for the required interfaces. This
change is a mid reduction in lines of code which is always a very nice thing!
|
|
Both PPPoE and WWAN interfaces are dialer interfaces handled by ppp, but use
different CLI nodes for the same functionality. PPPoE has "connect-on-demand"
to initiate an "on-demand" dialing and WWAN uses "ondemand" for this purpose.
Rename WWAN "ondemand" node to "connect-on-demand".
|
|
In the past we had to provide the ethertype value used for the VLAN
protocol (0x88A8 -> 802.1ad or 0x8100 -> 802.1q).
This should be changed to a more user friendly CLI node (protocol over
ethertype) and 802.1ad over it's raw value 0x88A8. There is no need in
presenting RAW information from the ethernet header to the user. Also iproute2
calls it protocol which makes way more sense over the "raw" value.
|
|
Despite the fact that running verify on Config() is "bad" and "not as intended"
the level of the configuration must match the keys that are checked by exits().
Re-set proper Config() level before querying the system nodes.
|
|
... an error would be presented: jinja2.exceptions.TemplateSyntaxError:
expected token 'end of statement block', got 'mhz_incapable', thus we simply
rename the key before rendering the template.
|
|
|
|
|
|
Removing a member from a bond/LACP will turn the physical interface always in
admin-down state. This is invalid, the interface should be placed into the state
configured on the VyOS CLI.
Smoketest on bond interfaces is extended to check this behavior.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Now that b40c52682a256 ("config: T2636: get_config_dict() returns a list on
multi node by default") is implemented the workarounds can be removed.
|
|
|
|
|
|
(https://github.com/Jacajack/mkjson.git)
|
|
|
|
Depending on the underlaying Kernel version load the corresponding Kernel
module.
|
|
rip: T2833: Fix distribute-list filter
|
|
|
|
|
|
|
|
|
|
|
|
Commit b082a6fb21 ("lcd: T2564: flatten CLI interface") by accident replaced
the template for hostapd which an LCD configuration during implementation of
T2564.
This has been corrected by restoring the content of the service configuration
from commit 8efb8ba1e (one commit earlier).
|
|
The current CLI did not support multiple prefix-delegations per interface. Some
ISPs only send one /64 to a client per prefix-delegation request, but they
allow the customer to request multiple prefixes.
The 'dhcpv6-options prefix-delegation' node has been renamed and converted to a
tag node named 'dhcpv6-options pd'. The tag node specifies a PD request (>=0).
In the past the user needed to know what prefix will be assigned and required
to calculate the sla-len by himself. The 'sla-len' node was dropped and is now
calculated in the background from the 'dhcpv6-options pd 0 length' node.
It is no longer mandatory to supply the 'sla-id' node, if sla-id is not
specified it is 'guessed' by counting upwards.
Example configuration:
----------------------
ethernet eth1 {
address dhcpv6
dhcpv6-options {
pd 0 {
length 56
interface eth2 {
address 1
}
}
}
}
This will request a /56 assignment from the ISP and will delegate a /64 network
to interface eth2. VyOS will use the interface address ::1 on the delegate
interface (eth2) as its local address.
|
