| Age | Commit message (Collapse) | Author |
|---|
|
When the 'powersave' option under 'system console' was defined but no actual
serial console device this cause the following error during migration:
Loading configuration from 'config.boot'
Traceback (most recent call last):
File "/opt/vyatta/etc/config-migrate/migrate/system/16-to-17", line 45, in <module>
for device in config.list_nodes(base + ['device']):
File "/usr/lib/python3/dist-packages/vyos/configtree.py", line 236, in list_nodes
raise ConfigTreeError("Path [{}] doesn't exist".format(path_str))
vyos.configtree.ConfigTreeError: Path [b'system console device'] doesn't exist
|
|
|
|
Boolean nodes have been removed b/c a boolean value makes less sense. The same
behavior can be achieved with the presence or absence of a node. Unfortunately
the 'autonomous-flag' node has been a negated one which did not migrate
it to 'no-autonomous-flag' if it was set to false previously.
|
|
StartLimitIntervalSec is part of the [Unit] definition and not the [Service]
definition [1]. This caused the following warning message:
systemd[1]: /lib/systemd/system/dhcp6c@.service:12: Unknown lvalue
'StartLimitIntervalSec' in section 'Service', ignoring
This error has been introduced via commit 992d356 ("dhcpv6-pd: T421: workaround
for non existing interfaces").
[1]: https://www.freedesktop.org/software/systemd/man/systemd.unit.html
|
|
When deleting a peth interface the interface name was not added to the
configuration dict, which lead to referencing non existent keys.
|
|
|
|
|
|
|
|
A user can define a port under the SSH node per device. WHen connecting to that
port and authenticating using regular credentials we will immediately drop to
the serial console. This is the same as executing "connect serial-proxy <name>".
|
|
|
|
For more examples on the new get_config_dict() approach migrate this
implementation as it is not yet in production use. Also this serves as proof of
concept code for further migrations.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
radvd[31898]: AdvValidLifeTime must be greater than AdvPreferredLifetime in
radvd.conf, line 19
This happens with the following configuration:
vyos@vyos# show service router-advert
interface eth0.20 {
name-server 2001:4860:4860::8888
prefix ::/64 {
valid-lifetime 7200
}
}
A validator is added to solve this issue and radvd will run again.
|
|
|
|
|
|
l2tp: T2602: Delete excess characters
|
|
For an unknown reason snmpd not always starts after reboot.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Only IP prefixes are allowed to be added by the CLI thus we can drop the
same check inside the Python script to validate the prefix.
|
|
|
|
Commit 5deb12c509be ("ssh: T2321: add VRF support") restructured the Port
assignment (cleanup from the early days) but it accesses a string with methods
used for a list, resulting in the funny default port 2.
|
|
tested using:
set nat destination rule 399 description 'Redirect DNS iot VLAN'
set nat destination rule 399 destination address '!192.168.67.243-192.168.67.244'
set nat destination rule 399 destination port '53'
set nat destination rule 399 inbound-interface bond10.204
set nat destination rule 399 log
set nat destination rule 399 protocol 'tcp_udp'
set nat destination rule 399 translation address '192.168.67.243'
set nat destination rule 399 translation port '53'
set nat destination rule 400 description 'Redirect DNS lan VLAN'
set nat destination rule 400 destination address '!192.168.67.243-192.168.67.244'
set nat destination rule 400 destination port '53'
set nat destination rule 400 inbound-interface bond10.204
set nat destination rule 400 log
set nat destination rule 400 protocol 'tcp_udp'
set nat destination rule 400 translation address '192.168.67.243'
set nat destination rule 400 translation port '53'
set nat destination rule 401 description 'Redirect DNS guest VLAN'
set nat destination rule 401 destination address '!192.168.67.243-192.168.67.244'
set nat destination rule 401 destination port '53'
set nat destination rule 401 inbound-interface bond10.204
set nat destination rule 401 log
set nat destination rule 401 protocol 'tcp_udp'
set nat destination rule 401 translation address '192.168.67.243'
set nat destination rule 401 translation port '53'
|
|
|
|
|
|
|
|
|
|
|
|
Only start console if it exists on the running system. If a user detaches a
USB serial console and reboots - it should not fail!
|
|
During testing it was discovered that there is a well known problem (we had for
ethernet interfaces) also in the serial port world. They will be enumerated and
mapped to /dev/ttyUSBxxx differently from boot to boot. This is especially
painful on my development APU4 board which also has a Sierra Wireless MC7710
LTE module installed.
The serial port will toggle between ttyUSB2 and ttyUSB5 depending on the
amount of serial port extenders attached (FT4232H).
The shipped udev rule (/usr/lib/udev/rules.d/60-serial.rules) partly solves
this by enumerating the devices into /dev/serial/by-id folder with their name
and serial number - it's a very good idea but I've found that not all of the
FT4232H dongles have a serial number programmed - this leads to the situation
that when you plug in two cables with both having serial number 0 - only one
device symlink will appear - the previous one is always overwritten by the
latter one.
Derive /usr/lib/udev/rules.d/60-serial.rules and create a /dev/serial/by-bus
directory and group devices by attached USB root port.
|
|
Support for Hayes modems has been long gone (1.2.x) and nobody cared. It was
removed in commit d582bbaf3 ("update console settings for systemd") of
vyatta-cfg-system.
So as there have been zero complaints - cleanup the CLI.
|
|
The current implementation only works once the system has been fully booted
up and the config nodes have been process. So there is no "early" kernel
debugging. It is started with priority 400 (after all network stuff) - thus it
has a questionable at all for Kernel debugging.
It would only make sense if the entire system is changed to supply the config
stuff to the Kernel commandline and then send it to a dedicated MAC address
target as network will be initialized late.
As there are zero Phabricator tasks available and we do not know any user using
this - the "feature" will be removed.
|
|
Migrate the serial console subsystem to XML and Python.
|
|
|
|
Instead of using "show version" as catch-all command for information rather
add "show system cpu" op-mode command which is analogous to "show system memory"
which deals with RAM.
|
|
* 'udev' of github.com:c-po/vyos-1x:
usb: op-mode: T2560: display USB interface information
pppoe: op-mode: T2488: retrieve log info from journalctl
wwan: op-mode: T2488: retrieve log info from journalctl
wwan: T2241: interface is not bond- or bridgeable
wwan: T2488: remove generation of dedicated logfile
wwan: T2529: migrate device from ttyUSB to usbXbY.YpZ.Z
udev: T2490: add persistent USB device files
|
|
|
